Smart Home Rowing Machine Model: SRM2000 FCC ID: 2AWJJ-RM2000 Item# M1S1 Last Modified: June 5, 2020 Email: support@sharevgo.
M1S1 ShareVgo Smart Home Rowing Machine Before You Begin Welcome to the ShareVgo community. Before beginning assembly, take a few moments to familiarize yourself with important information on how to use our ShareVgo Smart Rowing Machine safely so that you and your loved ones do not get hurt. Let’s review the safety notes and warnings now. If you have any questions, please contact support@sharevgo.
M1S1 ShareVgo Smart Home Rowing Machine FCC Statement and Important Labels CAUTION: The user is cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with Part 15 of the FCC Rules.
M1S1 ShareVgo Smart Home Rowing Machine Part Drawing 70 69 71 4
M1S1 ShareVgo Smart Home Rowing Machine Part List NO 1 2 NO 3 4 5 6 7 8 9 10 11 12A 12B 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33L 33R 34 35 Description Spec. Main Frame Front Base Tube Rear Base Tube Sliding Track Handlebar Washer Φ16*Φ8.5*1.5 Square Head Bolt M8*60 End Cap Φ50 Arc Washer Φ22*Φ8.5 Foam Grip 200 End Cap ∮28 Left Shroud A Left Shroud B Screw M4*20 Screw for Metal M4*20 Flange Nut M10*1.0 Hexagon Nut M10*1.
M1S1 ShareVgo Smart Home Rowing Machine Components For Assembly STEP 2 Components STEP 1 Components STEP 3 Components STEP 4 Components STEP 6 Components STEP2 STEP1 manual M8x55 M8x55 STEP4 STEP3 STEP5 #5 1PC #6 1PC 0 inch 0 cm 1 1 2 3 4 2 5 3 6 7 8 9 4 10 5 1 2 3 4 6 5 7 6 7 8 9 8 20 9 1 2 3 4 Hardware Pack & Manual 6
M1S1 ShareVgo Smart Home Rowing Machine Step 1 – Front Base Tube Assembly Attach the Front Base Tube, with two wheels (2) facing out, onto the Main Frame (1) and secure it by using 2 Bolts (7), and 2 Washers (9), and 2 Nuts (60). Tighten them using Allen Key (71). Wheel 71 Step 2 – Pedals Assembly Screw Bolts (32) into both the Rear Holes (A) at the main frame and tighten them with Wrench (71). Insert Bolts (32) through the Left Pedal (33L) and secure them to the Front Hole (B) of the main frame.
M1S1 ShareVgo Smart Home Rowing Machine Step 3 – Seat and Sliding Track Assembly Slide the Seat (53) onto the Sliding Track (4). Be sure to slide from the end that does not have the Rubber Stopper. 4 Insert the Pin (44) with the Stopper (35) through the hole near the end of the Sliding Track (4). Then attach the Rubber Stopper (35) to the other side and secure it with Screw (37). Tighten using both the Allen Key (69) and the Screwdriver (71).
M1S1 ShareVgo Smart Home Rowing Machine Step 5 – Connect Sliding Track to Main Frame Lift up the u-shaped open end of the Main Frame (1) and the front end of the Sliding Track (4). Insert the front end of the Sliding Track into the u-shaped open end of the Main Frame (1). 43 42 40 1 4 38 Lift the end of the Sliding Track (4) to 20-30 degree so that the Cylinder Block can go in the u-shaped opening of the Main Frame (1).
M1S1 ShareVgo Smart Home Rowing Machine Step 6 – Tablet Holder Assembly 6-2 6-1 - 49 6-1: Install 2 AAA batteries into the slot at the back of Monitor (49). 68 68 6-3 49 49 68 66 41 41 66 46 1 66 6-3: Attach Monitor (49) to the Monitor Plate (66) using the 4 Screws (68). Connect the two Sensor Wires (41) to the two Monitor Sensor Wires (49) and make sure it is properly connected.
M1S1 ShareVgo Smart Home Rowing Machine To Move or Fold Rowing Machine - To fold rowing machine for storage, 1. Unscrew and release Knob (43) and Washer (42). 2. Pull out the Safety Pin (39). 3. Lift up the Sliding Track (4) with one hand. 4. Insert Safety Pin (39) to Hole C. 5. Screw and tighten Knob (43) with Washer (42) into Hole D. CAUTION: To avoid slamming by Sliding Track, be sure to hold the Sliding Track when you insert or remove the Safety Pin (39) and Knob (43).
M1S1 ShareVgo Smart Home Rowing Machine Monitor Operation & Function Function buttons: MODE: 1. Press to select functions for display. 2. Press and hold 3-5 seconds to reset time, distance, and count values to zero. SET: 1. Press to set target functions for time, distance, and count. 2. Press and hold 3-5 seconds to reset time, distance, and count values to zero. RESET: 1. Press to reset the setting values to zero. 2. Press and hold 3-5 seconds to reset time, distance, and count values to zero.
M1S1 ShareVgo Smart Home Rowing Machine Connecting to Mobile Device STEP 1 - Get it assembled Make sure your equipment is assembled properly, batteries are installed, and the monitor with Bluetooth® is ON. STEP 2 - Get the app Download the ShareVgo Fitness app from Google Play or the App StoreTM on a compatible phone or tablet. STEP 3 - Set up Find QR code on the equipment you purchased. Follow the on-screen steps to register your equipment and sign-up an account.
M1S1 ShareVgo Smart Home Rowing Machine Maintenance and Storage Inspect all parts and make sure all nuts, bolts, and screws are completely tightened before each use. To clean, wipe this equipment with a damp cloth. DO NOT use abrasive cleaners or solvents. Store your equipment at a stable position, in clean and dry environment away from children.
M1S1 ShareVgo Smart Home Rowing Machine Product Warranty 90-day Limited Warranty ShareVgo, LLC. warrants that this product will be free from defects in materials and workmanship for a period of 90 days from date of purchase when purchase of the product is from an authorized retailer and is used for the purpose intended, under the conditions that it has been installed and operated in according to ShareVgo’s Owner’s Manual.
