October 2016 05-0857-200
Design © 2016 Xerox Corporation. All rights reserved. Xerox®, Xerox and Design® and DocuMate® are registered trademarks of Xerox Corporation in the United States and/or other countries. BR19347 Content © 2016 Visioneer, Inc. All rights reserved. The Visioneer brand name and OneTouch® logo are registered trademarks of Visioneer, Inc.
Table of Contents Safety ................................................................................................................................v Safety Introduction ................................................................................................................................v Operational Safety Information.......................................................................................................v Electrical Information..................................................
Xerox® DocuMate® 5445 / 5460 Table of Contents Using the Mixed Batch Card Guide ............................................................................................. 25 Detach or Attach the Mixed Batch Card Guide ......................................................... 26 Scanning from the Automatic Document Feeder (ADF) ................................................... 27 Scanning Thick Pages or Bound Documents...........................................................................
Safety Safety Introduction Notices and Safety Please read the following instructions carefully before operating the machine and refer to them as needed to ensure the continued safe operation of your machine. Your Xerox® product and supplies have been designed and tested to meet strict safety requirements. These include safety agency evaluation and certification, and compliance with electromagnetic regulations and established environmental standards.
Xerox® DocuMate® 5445 / 5460 Safety Note: Your Xerox® machine is equipped with an energy saving device to conserve power when the machine is not in use. The machine may be left on continuously. Do not do these: • Never use a ground adapter plug to connect the equipment to a power outlet that lacks a ground connection terminal. • Never attempt any maintenance function that is not specifically described in this documentation. • Never remove covers or guards that are fastened with screws.
Xerox® DocuMate® 5445 / 5460 Safety Electrical Supply • This product shall be operated from the type of electrical supply indicted on the product’s data plate label. If you are not sure that your electrical supply meets the requirements, please consult your local power company for advice. • Always connect equipment to a correctly grounded power outlet. If in doubt, have the outlet checked by a qualified electrician.
Xerox® DocuMate® 5445 / 5460 Safety 3. Do not use aerosol cleaners. The use of cleaners that are not approved may cause poor performance of the equipment, and could cause a dangerous condition. 4. Use supplies and cleaning materials only as directed in this manual. 5. Do not remove covers or guards that are fastened with screws. There are no parts behind these covers that you can maintain or service. 6.
Welcome Your new Xerox® scanner can quickly scan stacks of single-sided or double-sided pages and place their electronic images on your computer. What’s in the Box Before proceeding, check the contents of the box. If items are missing or damaged, contact the dealer where you purchased the scanner.
Xerox® DocuMate® 5445 / 5460 • DVD-ROM drive capable of reading Dual Layer DVDs • Universal Serial Bus (USB) port • Microsoft® Windows® operating system: – 32-bit Windows XP (Service Pack 3) – 32-bit or 64-bit Windows Vista (Service Pack 2) – 32-bit or 64-bit Windows 7 (Service Pack 1) – 32-bit or 64-bit Windows 8 / 8.
Welcome • • • • • Xerox® DocuMate® 5445 / 5460 Control sheets—automatically adjust the scan settings when scanning using the TWAIN interface. The file contains layouts for various ISO and U.S. paper sizes. The TWAIN scanning chapter contains instructions on using these sheets while scanning. Make sure you print the page size that matches the size of the pages in your document stack.
Xerox® DocuMate® 5445 / 5460 Welcome The Xerox® DocuMate® 5445 / 5460 Scanner Features 1 5 2 6 3 7 4 1. 8 Input Tray—Holds the documents in the Automatic Document Feeder for scanning. – Paper Guides—Slide to adjust to document width. 2. ADF Cover Release—Press to open the Automatic Document Feeder. 3. Automatic Document Feeder—Feeds documents through the scanner during scanning. 4. Output Tray—Holds documents after being scanned.
Xerox® DocuMate® 5445 / 5460 Welcome Control Panel 1 2 4 5 3 6 8 7 1. LED number—shows the OneTouch function that will be used for scanning. You can view the scan settings for that function in the OneTouch Properties window. When there is a hardware error, the LED number indicates what the hardware error code is. 2. LED function button—tap the button to cycle through the 9 OneTouch scanning options. 3.
Xerox® DocuMate® 5445 / 5460 6 Welcome User Guide
Scanner Setup Unpack the scanner Remove any tape from the scanner body. Use care while removing the tape, the tape holds fragile parts in place for shipping. Note: we recommend you remove the tape from the scanner in the order indicated in the illustrations below. Also remove any protective foam from the inside of the scanner while you are removing the packaging tape. 2 1 Press the ADF cover release button and open the scanner.
Xerox® DocuMate® 5445 / 5460 Scanner Setup Place the scanner on a level surface near the computer. • Keep clear space on every side of the scanner for the input and exit tray extensions, performing maintenance, and to have sufficient air flow for ventilation. Attach the Input Tray 1. Align the tabs on the input tray with the holes in the scanner body. 2. Slide the input tray into position.
Scanner Setup 3. Xerox® DocuMate® 5445 / 5460 Push firmly on the input tray until you hear it lock in place. Connect the Scanner Power Cord Note: Only use the power supply (PNLV6507Y) included with your scanner. Connecting any other type of power supply may damage your scanner, and will void its warranty. 1. Plug the power supply into the power port on the scanner. 2. Plug the power cord into the power supply and into a wall outlet.
Xerox® DocuMate® 5445 / 5460 10 Scanner Setup User Guide
Installation Please make sure of the following before you begin installation: • If you are prompted to reboot during installation, please select “No”. Finish installing the rest of the software, then close all open windows and reboot your computer. • The information in this guide may cover software not provided with the scanner you purchased. Please disregard any information about the software not applicable to your scanner.
Xerox® DocuMate® 5445 / 5460 2. Installation Insert the installation disc into your computer’s DVD-ROM drive. The disc automatically starts. 3. The Select Language window opens. Click the drop-down menu arrow and select the language to use. Click OK. The disc’s Main menu window opens. Note: If the disc does not start, check the following: – Make sure the disc drives door is completely shut. – Make sure the disc was inserted in the drive in the proper direction (label side up).
Installation Xerox® DocuMate® 5445 / 5460 4. On the Main menu, select Install software. 5. Make sure the boxes for Scanner Driver and Visioneer OneTouch are selected, as well as any other applications you want to install. Note: The software provided with your scanner may differ slightly from the list shown in the window. 6. Click Install now.
Xerox® DocuMate® 5445 / 5460 Installation Installing the Scanner Driver The scanner driver installation will start first. 1. The Welcome screen for the scanner driver Setup Wizard opens. Click Next. Note: there may be an option in the installation window to remove any current scanning profiles. You will see this prompt if you already have a previous version of the scanner driver installed. Select the option in the installation window only if you want the existing profiles removed. 2.
Installation 4. Xerox® DocuMate® 5445 / 5460 Stop when you see the “Complete the installation by connecting your hardware” window. Do not click OK yet. Leave the window open and proceed to the next section. Note: If you do not see this on-screen diagram for connecting the scanner, stop and follow the instructions below. Connect the USB Cable and Turn on the Power 1. Remove any tape from the USB cable. 2. Plug the USB cable into the USB port on the scanner then into a USB port on the computer.
Xerox® DocuMate® 5445 / 5460 3. Installation Turn on the scanner power. The status light comes on and flashes indicating that the scanner is receiving power. Your computer recognizes that a scanner has been plugged into the USB port and automatically loads the appropriate software to run the scanner. 4. When you’re certain that the software has completely loaded, return to the “Complete the installation by connecting your hardware” window. 5. Click OK to complete the installation process.
Installation 6. Xerox® DocuMate® 5445 / 5460 Click Close on the Installation Complete window to close and exit the driver installer. User Utility Installation The User Utility installation will automatically start after you close the TWAIN installation. The User Utility is a software diagnostic and maintenance software that you can use for monitoring your scanner hardware. 1. On the Xerox User Utility License Agreement window, read the license agreement.
Xerox® DocuMate® 5445 / 5460 Installation Installing the ISIS Driver 1. You will first be prompted to select a language for the ISIS driver. The language selection on this screen only applies to the ISIS scanning interface. Select the language you want to use then click on Next. 2. Click on Next in the ISIS Installation Welcome window. 3. Click on Install to begin the ISIS driver installation. 4. Click on Finish to close the ISIS installation complete window.
Xerox® DocuMate® 5445 / 5460 Installation Installing Additional Applications Your scanner includes free, additional applications as described in the table below. 1. Return to the disc’s Main menu and click Install software. 2. Select the additional applications you want to install, then click Install now. 3. Follow the instructions on the screen to install each of the additional applications. Software About the Software Nuance PaperPort® PaperPort is a document management software application.
Xerox® DocuMate® 5445 / 5460 Installation View the User Guides 1. Return to the disc’s Main menu and click on View user guides. 2. Click on View scanner documentation to access the scanner user guide and scanning guides for OneTouch and TWAIN.
Installation Xerox® DocuMate® 5445 / 5460 Register Your Scanner Registering your scanner is important as it provides you with access to our free telephone support service. Registration also gives you free access to software updates for your scanner. You will need an active network connection to register your scanner. If you do not have network access you can contact our customer service department to register the scanner.
Xerox® DocuMate® 5445 / 5460 Installation 22 User Guide
Loading Documents to Scan Always remove any staples or paper clips from documents before inserting them into the scanner. Staples and paper clips can jam the feed mechanism and scratch the internal components. Also remove any labels, stickers, or Post-It™ notes that may come off during the scanning process and get stuck in the scanner. Misuse as described here will void your scanner’s warranty. Please go to www.xeroxscanners.
Xerox® DocuMate® 5445 / 5460 – Loading Documents to Scan We recommend changing the Document handling speed to Delicate in the TWAIN interface when scanning thin paper of approximately 11 lbs (40 g/m2) or thinner. Additionally, we recommend using the slow paper feeding speed if you are scanning fragile documents. Note: The minimum custom item size is 1.9 x 2.13 inches (48 x 54 mm). This means that you cannot scan business cards size 3.5 x 2 inches in the landscape orientation.
Loading Documents to Scan Xerox® DocuMate® 5445 / 5460 • Extremely smooth, shiny, or highly textured paper may cause the paper feed rollers to slip across the page and cause the scanner to report a paper jam. • Carbonless copy paper may tear while being fed through the scanner and the pressure of the rollers may leave streaks on the page. The chemical coating on this paper will rub off on the rollers during the scan process, increasing the frequency of miss-feeds and paper jams.
Xerox® DocuMate® 5445 / 5460 Loading Documents to Scan Detach or Attach the Mixed Batch Card Guide The card guide is pre-installed in the scanner. After removing the shipping tape lift up on the card guide to remove it from the scanner. After you remove the card guide from the scanner you can attach it to the back of the input tray. Slide the paper guide into the tabs on the back of the input tray as indicated in the illustration below.
Loading Documents to Scan Xerox® DocuMate® 5445 / 5460 Scanning from the Automatic Document Feeder (ADF) Preparing Documents for Scanning • Fan the documents to make sure all pages in the stack are separated. • Bend and then flatten the document stack to make sure the horizontal edges are aligned to help prevent paper from skewing while being pulled through the scanner. • Pinch the ends to align the leading edges slantwise to help prevent multiple pages from being fed through at a single time.
Xerox® DocuMate® 5445 / 5460 • Loading Documents to Scan Place the documents face down in the input tray. Set the leading edge of the documents as shown in the illustration below. Important: the paper capacity for the input tray is 75 pages of standard 20 lb printer paper. You cannot place a full stack of pages in the scanner if the card guide is installed in the scanner. Please refer to page 26 for instructions on removing and storing the card guide.
Loading Documents to Scan Xerox® DocuMate® 5445 / 5460 1. Open the scanner. 2. Locate the paper thickness switch in the underside of the ADF door. 3. Pull the paper thickness switch up as indicated in the illustration below. When you pull the paper thickness switch the double feed prevention roller disengages and sits back into the scanner. 4. Close the ADF door. When you close the ADF door the double feed prevention roller will no longer touch the feed roller. 5.
Xerox® DocuMate® 5445 / 5460 Loading Documents to Scan Scanning Interfaces • OneTouch Control Panel—When you press the Start button on the scanner, the scanner starts scanning using the settings for the current LED number. The scanned image is then sent to a destination on your computer or network drive. OneTouch Button Panel—Use this scan option when you want to scan from the computer screen.
Loading Documents to Scan • Xerox® DocuMate® 5445 / 5460 TWAIN and WIA Interface—This option uses your scanner’s TWAIN interface to scan. Select scanning options before scanning, put the document in the scanner, then click the Scan button in the TWAIN interface window. Please see the TWAIN Scanning Guide on the installation disc for instructions. You can also click the Help button in the TWAIN interface to open the instructions in an Internet browser.
Xerox® DocuMate® 5445 / 5460 32 Loading Documents to Scan User Guide
Maintenance This section contains information about maintenance, troubleshooting, uninstalling, scanner specifications, and spare parts. Safety Precautions When servicing the scanner you should take the following precautions to ensure your safety and prevent damage to the scanner. Do These • Wear protective gloves when cleaning the scanner with Isopropyl rubbing alcohol. Rubbing alcohol may irritate sensitive skin. • Only perform scanner maintenance as described in this chapter.
Xerox® DocuMate® 5445/5460 Maintenance Hardware Properties You can use the scanner’s properties page to keep track of scanner maintenance, change some of the hardware options, configure the scanner interface behavior, and adjust application options that may be available for your scanner. To open the scanner hardware properties page: • Windows 7 and later—from the Windows Control Panel, open Hardware and Sound and then Devices and Printers.
Maintenance Xerox® DocuMate® 5445/5460 Power Settings Some features described herein may not be available for the current scanner. • Sleep mode—sleep mode is the low-power state when the scanner is not in use. You can adjust the amount of time you want the scanner to wait before it goes into low power. Click the green enter button to save any changes in the Sleep mode field. Click the red reset button to reset to the default timeout value.
Xerox® DocuMate® 5445/5460 Maintenance Driver Settings The options in this panel are for configuring how the TWAIN interface will behave in some scenarios. Please see the TWAIN scanning guide on the installation disc for instructions. Clearing Paper Jams Depending on the paper type, scanning results may be poor even when you scan documents that are in the list of acceptable document types on page 23.
Maintenance 2. Xerox® DocuMate® 5445/5460 Remove the jammed paper and close the cover. To reduce the number of paper jams, smooth and straighten the paper before scanning, adjust the guides to the paper size, and insert the paper evenly into the ADF. Note: If the paper jam occurs only at the exit area, remove the exit guides and then try scanning again. To detach the exit guides: 1. Close the trays. 2. Remove the input tray by carefully but firmly pulling it away from the scanner. 3.
Xerox® DocuMate® 5445/5460 4. Maintenance Carefully and firmly pull the exit guides away from the scanner. The exit guides are hard plastic arms that snap on to a bar in the exit path of the scanner. Be sure to pull the exit guides straight away from the scanner. Do not bend or twist the guides while trying to detach them as it will cause the plastic to crack and break. 5. Set the exit guides aside where you can find them. T WARNING: The exit guides are small enough to pose a choking hazard.
Maintenance Xerox® DocuMate® 5445/5460 To attach the exit guides: 1. Close the trays. Remove the input tray by carefully but firmly pulling it away from the scanner. Place the scanner on its back. 2. Locate notches in the underside of the exit path where the guides are going to be attached. 3. Align the exit guide clips to the bar and push firmly on the guides until they snap onto the bar. The exit guides are hard plastic arms that snap on to a bar in the exit path of the scanner.
Xerox® DocuMate® 5445/5460 Maintenance Cleaning the Inside of the Scanner Cleaning the inside of the scanner helps to keep your scanner operating at optimum performance. You should clean the inside of the scanner at least once a week or after 2,000 pages have been scanned. If you are getting frequent paper jams, multiple pages feeding at the same time, or you’re seeing lines in the scanned image, it is time to clean the scanner.
Maintenance • Xerox® DocuMate® 5445/5460 You will need a cotton swab. Cleaning the Sensors 1. Press the ADF cover release button and open the scanner. 2. The following illustration shows the location of the sensors in the scanner. 3. Carefully clean the sensors with a dry cotton swab. Cleaning the Rollers Preparation • You will need a roller cleaning paper for cleaning the rollers. Roller cleaning papers can be purchased from our website at www.xeroxscanners.
Xerox® DocuMate® 5445/5460 • Maintenance Use scissors to open the roller cleaning paper bag, cutting across the dotted line. Note: When cleaning the rollers, do not rub the roller cleaning paper vigorously back and forth across the roller, this will shred the roller cleaning paper and leave debris in the scanner. Safety Precautions • Keep the roller cleaning paper away from fire, heaters or any open flame or heat source as any form of alcohol is flammable.
Maintenance 2. Xerox® DocuMate® 5445/5460 The following illustration shows where the rollers are located in the scanner. Use a roller cleaning paper to clean all of the rollers indicated in the illustration. Note: Be careful when cleaning the rollers. All of the rollers, except the free rollers, are designed to rotate in one direction only. Do NOT force the roller to rotate in the opposite direction. Forcing the roller to rotate will damage it, and cause the scanner to feed pages incorrectly. 3.
Xerox® DocuMate® 5445/5460 Maintenance Replacing the Rollers The roller will wear out and is designed to be a user-replaceable part. A worn roller can cause documents to feed in skewed at an angle, or multiple pages to feed at the same time. Before replacing the roller you should clean it as excessive dust on the roller will make it appear worn and smooth. You cannot properly diagnose a worn roller until you have cleaned it. You should generally replace the roller between 160,000 and 200,000 scans.
Maintenance Xerox® DocuMate® 5445/5460 2. Remove the roller from the scanner. Angle it out and away from the gear in the scanner. 3. Insert the roller into the scanner. Align the gear on the roller with the gear in the scanner and angle the other side of the roller down into the scanner. 4. Close the roller cover. Press gently on both sides of the roller cover until it clicks into place.
Xerox® DocuMate® 5445/5460 5. Maintenance When you are done replacing the roller, manually rotate the roller in the direction it feeds the paper to verify that the roller is installed correctly. Replacing the Double Feed Prevention Roller 1. Locate the roller in the ADF door and pull open the roller cover. 2. Remove the roller from the scanner. Slide the roller straight out from the scanner.
Maintenance Xerox® DocuMate® 5445/5460 3. Insert the new roller into the scanner. Make the side of the bar with the longer groove is on the right side when looking at the scanner as indicated in the illustration below. 4. Close the roller cover. User Utility The User Utility is a software program designed to help maintain and troubleshoot your Xerox scanner. On installation you were prompted to place an icon on your Windows desktop.
Xerox® DocuMate® 5445/5460 Maintenance Main Screen Options This section briefly describes the options on the main interface of the User Utility. The following sections contain detailed instructions on using some of the options in this utility. Scanner Status—this area displays the status of the scanner connected as well as error code details. Error Code—this field displays an error code number to help you diagnosis and resolve hardware errors.
Maintenance Xerox® DocuMate® 5445/5460 • Vertical Line Reduction: clicking on this button initiates the vertical line adjustment utility. Please see “Vertical Line Reduction” on page 52 for instructions. • Caution Setting: clicking this button opens a window for you to set when to receive a notice that it is time to clean the rollers. Scanner Counter—this section shows the number of pages scanned. Use the options in this window to keep track of maintenance performed on the scanner.
Xerox® DocuMate® 5445/5460 Maintenance Error Code Message Cause Resolution U11 A paper jam has occurred. Paper has jammed while being fed through the scanner. Open the scanner’s door, remove documents, and then close the door. Place the documents back in the document input tray. Please see page 36 for complete instructions. U12 U13 U14 U15 U16 If the problem persists, clean the rollers as described in the section “Cleaning the Scanner” on page 39. U18 Paper remains in the scanner.
Xerox® DocuMate® 5445/5460 Maintenance Error Code Message Cause Resolution — ***Caution*** The number next to After Clean Roller, in the User Utility main screen, has exceeded the maximum number between cleaning. The rollers should be cleaned every 2,000 scans, or as needed if your scanner is experiencing frequent paper feed issues. After cleaning the rollers click on Clear Counter to reset the cleaning roller count back to 0. Please refer to “Cleaning the Scanner” on page 39.
Xerox® DocuMate® 5445/5460 3. When the Sleep Mode window opens, select the options you want. – Waiting Time—set the waiting time before sleep mode or power off activates when the scanner is idle. This time can be set from 1 to 60 minutes or from 15 to 60 minutes. The range of this setting differs depending on the scanner model. • – 4. Maintenance If the wait time for Power Off is shorter than the wait time for Sleep Mode, the scanner will not enter Sleep Mode.
Maintenance Xerox® DocuMate® 5445/5460 4. When prompted to clean the scanner click on OK to proceed only if you have already cleaned the scanner during preparation. Otherwise, follow the instructions on screen and clean the scanner. 5. Place the 3 sheets of plain white paper in the scanner’s input tray and then click on OK. 6. The scanner will pull the pages through as it sets the adjustment. This window will automatically close when the initial adjustment is complete. 7.
Xerox® DocuMate® 5445/5460 Maintenance 2. On the main window click on the Vertical Line Reduction... button. 3. Click on the Restore Default button. 4. Click on OK to restore the factory default adjustment. 5. When the adjustment has been restored, click on OK to close the User Utility restore window. Uninstalling Your Scanner Use the options in the Windows Control Panel to remove the scanner driver and modules, and any other software provided with the scanner.
Maintenance Xerox® DocuMate® 5445/5460 Uninstalling Visioneer Acuity™: Visioneer Acuity is automatically installed when you install the scanner driver using the installation disc. You can also download the Visioneer Acuity module from the support pages for your scanner at www.xeroxscanners.com. Visioneer Acuity is a utility with advanced image processing options to instantly improve the visual clarity of anything you scan. 1. In the list of installed programs select Visioneer Acuity Assets. 2.
Xerox® DocuMate® 5445/5460 Maintenance • Try cleaning the scanner. There is glass in the body of the scanner and underneath the lid. Take a soft cloth and wipe across both pieces of glass. The section “Cleaning the Scanner” on page 39 contains thorough instructions for cleaning this part of the scanner. • If cleaning the glass does not improve the image quality, try performing a vertical line reduction adjustment. The line reduction adjustment recalibrates the scanner.
Xerox® DocuMate® 5445/5460 Maintenance Problem: The ADF won’t feed pages properly. A dirty or worn roller can cause documents to feed in skewed at an angle, or multiple pages to feed at the same time. First, try cleaning the rollers as described in “Cleaning the Scanner” on page 39. If the problem persists, the separation and/or feed rollers may need to be replaced. Please see “Replacing the Rollers” on page 44.
Xerox® DocuMate® 5445/5460 Maintenance Scanner Specifications Maximum Item Size Firmware version lower than 2.0 • 8.5 x 100 inches (216 x 2540 mm) Firmware version 2.0 and higher • Maximum page length varies by resolution Resolution Xerox DocuMate 5445 Xerox DocuMate 5460 75 dpi* 8.5 x 150 inç (216 x 3810 mm) 8.5 x 195 inç (216 x 4953 mm) 100 dpi 8.5 x 150 inç (216 x 3810 mm) 8.5 x 195 inç (216 x 4953 mm) 150 dpi 8.5 x 150 inç (216 x 3810 mm) 8.5 x 195 inç (216 x 4953 mm) 200 dpi 8.
Xerox® DocuMate® 5445/5460 Maintenance Scanner Specifications Relative Humidity 20% ~ 80% (@30° C without condensation) Scanner Dimensions Width 12,5 inches (318 mm) Depth 8,2 inches (208 mm) Height 7,7 inches (196 mm) Weight 8 pound (3,65 kg) Power Information Power Supply AC-ADAPTER (PNLV6507Y) DC jack, 2P, 100–240Vac, 50–60 Hz, 16Vdc/1.
Xerox® DocuMate® 5445/5460 Maintenance Xerox® DocuMate® 5445 / 5460 Parts List Part Name Part Number Input Tray 57-0148-000 Roller Exchange Kit 70-0567-000 Separation Roller Feed Roller USB Cable 35-0241-000 AC Power Cord 35-0242-000 or 35-0243-000(US) 35-0244-000 or 35-0245-000 (EUR) 35-0246-000 or 35-0246-100 (UK) Power Supply 60 37-0097-100 User Guide
Regulatory Information Basic Regulations United States (FCC Regulations) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Xerox® DocuMate® 5445 / 5460 Regulatory Information This machine is certified as Class 1 LED product. This means that this machine does not produce hazardous laser radiation.
Xerox® DocuMate® 5445 / 5460 Regulatory Information 1. Obligations or Securities of the United States Government, such as: Certificates of Indebtedness National Bank Currency Coupons from Bonds Federal Reserve Bank Notes Silver Certificates Gold Certificates United States Bonds Treasury Notes Federal Reserve Notes Fractional Notes Certificates of Deposit Paper Money Bonds and Obligations of certain agencies of the government, such as FHA, etc. Bonds. (U.S.
Xerox® DocuMate® 5445 / 5460 Regulatory Information The above list is not all inclusive, and no liability is assumed for its completeness or accuracy. In case of doubt, consult your attorney. Canada Parliament, by statute, has forbidden the reproduction of the following subjects under certain circumstances. Penalties of fines or imprisonment may be imposed on those guilty of making such copies. 1. Current bank notes or current paper money. 2. Obligations or securities of a government or bank. 3.
Regulatory Information Xerox® DocuMate® 5445 / 5460 Note: this list is not inclusive and no liability is assumed for either its completeness or accuracy. In case of doubt, contact your legal counsel.
Xerox® DocuMate® 5445 / 5460 66 Regulatory Information User Guide
Compliance Information Product Recycling & Disposal USA & Canada If you are managing the disposal of your Xerox® product, please note that the product may contain lead, mercury, Perchlorate, and other materials whose disposal may be regulated due to environmental considerations. The presence of these materials is fully consistent with global regulations applicable at the time that the product was placed on the market. For recycling and disposal information, contact your local authorities.
Xerox® DocuMate® 5445 / 5460 Compliance Information ENERGY STAR for the USA Energy Program Compliance The Xerox® DocuMate® 5445 / 5460 is ENERGY STAR qualified under the ENERGY STAR Program Requirements for Imaging Equipment. The ENERGY STAR and ENERGY STAR MARK are registered United States trademarks. The ENERGY STAR Imaging Equipment Program is a team effort between U.S.
