User Manual
Table Of Contents
- User Guide
- 1 Safety
- 2 Learn about the printer
- 3 Set up, install, and configure
- Selecting a location for the printer
- Attaching cables
- Finding the IP Address of the Printer
- Setting up the printer to fax
- Configuring the Email SMTP Settings
- Loading paper and specialty media
- Installing and updating software, drivers, and firmware
- Installing the Software
- Operating System Requirements
- Installing the Print Drivers for a Windows Network Printer
- Installing the Windows Print Driver .zip File
- Installing the Print Drivers for a Windows USB Printer
- Installing the Printer as a Web Service on Devices
- Installing the Drivers and Utilities for MacOS
- Installing Print Drivers and Utilities for UNIX and Linux
- Updating Firmware
- Exporting or importing a configuration file
- Installing the Software
- Networking
- Printing the Menu Settings Page
- 4 Secure the printer
- 5 Print
- 6 Copy
- 7 Email
- 8 Fax
- 9 Scan
- 10 Use printer menus
- 11 Maintain the Printer
- 12 Troubleshoot a problem
- Print quality problems
- Printing problems
- Print quality is poor
- Blank or White Pages
- Dark Print
- Fine lines are not printed correctly
- Folded or wrinkled paper
- Gray Background
- Incorrect margins
- Light print
- Mottled print and dots
- Paper curl
- Print crooked or skewed
- Solid black pages
- Text or images cut off
- Toner easily rubs off
- Horizontal light bands
- Vertical light bands
- Vertical white lines
- Vertical dark bands
- Vertical dark lines or streaks
- Vertical dark streaks with print missing
- Repeating defects
- Print jobs do not print
- Job prints from the wrong tray or on the wrong paper
- Slow printing
- Print quality is poor
- The printer is not responding
- Unable to read flash drive
- Enabling the USB port
- Network connection problems
- Issues with supplies
- Clearing Jams
- Paper feed problems
- E-mailing problems
- Faxing problems
- Scanning problems
- Cannot scan to a computer
- Cannot scan to a network folder
- Partial copies of document or photo
- Scan job was not successful
- Poor copy quality
- Vertical dark streaks on output when scanning from the ADF
- Scanner does not close
- Scanning takes too long or freezes the computer
- Scanner does not respond
- Adjusting scanner registration
- Adjusting ADF registration
- Contacting Customer Support
- A Regulatory Information
- Basic Regulations
- Noise Emission Levels
- Static Sensitivity Notice
- ENERGY STAR
- Temperature Information
- Información de la energía de México
- Laser Notice
- Power
- Telecommunication Regulatory Notices
- Regulatory Notices for Wireless Products
- Federal Communications Commission (FCC) Compliance Information Statement
- Innovation, Science and Economic Development Canada Compliance Statement
- Germany
- Turkey RoHS Regulation
- Ukraine RoHS Compliance
- Copy Regulations
- Material Safety Data Sheets
- Basic Regulations
- B Recycling and Disposal
CAUTION—POTENTIAL INJURY: When moving the printer, follow these guidelines to avoid
personal injury or printer damage:
• Make sure that all doors and trays are closed.
• Turn off the printer, and then unplug the power cord from the electrical outlet.
• Disconnect all cords and cables from the printer.
• If the printer has separate floor-standing optional trays or output options attached to it,
then disconnect them before moving the printer.
• If the printer has a caster base, then carefully roll it to the new location. Use caution when
passing over thresholds and breaks in flooring.
• If the printer does not have a caster base but is configured with optional trays or output
options, then remove the output options and lift the printer off the trays. Do not try to lift
the printer and any options at the same time.
• Always use the handholds on the printer to lift it.
• Any cart used to move the printer must have a surface able to support the full footprint of
the printer.
• Any cart used to move the hardware options must have a surface able to support the
dimensions of the options.
• Keep the printer in an upright position.
• Avoid severe jarring movements.
• Make sure that your fingers are not under the printer when you set it down.
• Make sure that there is adequate clearance around the printer.
CAUTION—HOT SURFACE: The inside of the printer might be hot. To reduce the risk of injury
from a hot component, allow the surface to cool before touching it.
CAUTION—PINCH HAZARD: To avoid the risk of a pinch injury, use caution in areas marked
with this label. Pinch injuries may occur around moving parts, such as gears, doors, trays, and
covers.
CAUTION—MOVING PARTS: Indicates a risk of laceration or abrasion injuries from rotating
parts.
CAUTION—POTENTIAL INJURY: This product uses a laser. Use of controls or adjustments or
performance of procedures other than those specified in the User Guide may result in
hazardous radiation exposure.
CAUTION—POTENTIAL INJURY: The lithium battery in this product is not intended to be
replaced. There is a danger of explosion if a lithium battery is incorrectly replaced. Do not
recharge, disassemble, or incinerate a lithium battery. Discard used lithium batteries according
to the manufacturer instructions and local regulations.
This product is designed, tested, and approved to meet strict global safety standards with the use of
specific manufacturer components. The safety features of some parts may not always be obvious.
The manufacturer is not responsible for the use of other replacement parts.
Refer service or repairs, other than those described in the user documentation, to a service
representative.
14
Xerox
®
B225/B235 Multifunction Printer
User Guide
Safety