OPERATOR MANUAL Initial issue: 02/03 Latest revision: 10/03 9.
This page is intentionally left blank.
TABLE OF CONTENTS INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 DESCRIPTION OF THE PROCESS . . . . . . . . . . . . . . . . . . . . . . . . . .6 DESCRIPTION OF THE MACHINE . . . . . . . . . . . . . . . . . . . . . . . . . .7 1 - Features description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7 2 - Technical specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8 JAM DETECTION . . . .
This page is intentionally left blank.
INTRODUCTION This manual provides informations for operating the Xerox Interface Module. Welcome to the Xerox Interface Module. This product is an interface for the DocuTech 120 printer. The XIM will enable in line finishing by receiving sheets from the host printer and sendinig these sheets in to a stacker or other Finishing device. The information contained in this manual is based on the most current information available at the time of editing.
DESCRIPTION OF THE PROCESS Schematic view of the paper path.
DESCRIPTION OF THE MACHINE 1 - Features description Top tray IN Led display Top cover OUT Front OUT Power cord The power supply cord is used as the disconnect device. There is no Main switch. Front door Docking plate to downstream device. Keyboard and switch for service use only. General: Height of the entrance / exit: 860mm / 33.8in. Height of the exit : 860 mm (33.8 in.) or 1020mm (40.1 in.) (Adjustable : + 60mm / 2.4in. and - 15mm / .6in.).
2 - Technical specifications Paper type: Min: 178 mm (7 in.) Max: 470 mm (18.5 in.) Min: 254 mm (10 in.) Max: 364 mm (14.33 in.
LEF 215x330 Foolscap – XE 220x330 Legal 9x14 SB4 B4 –JIS 8K (Taiwan)3 A3 Ledger 12x18 12x18.5 12.2x17 4 up-6x9 2 up-6x9 SRA4 2 up-A5 SRA3 4 up-A5 Labels Paper Size / Orientation SEF Inches X (8.46x13) X X X X X X X X X X X X X X X X X X PPM mm 215x330 8.5x13 (216x330) (8.66x13) 220x330 8.5x14 (216x356) 9x14 (229x356) (9.9x14.1) 252x358 (10.12x14.33) 257x364 (10.51x15.28) 267x388 (11.69x16.54) 297x420 (11x17) (279x432) 12x18 (305x457) 12x18.5 (305x470) (12.2x17) 310x432 12.5x18.5 (317.5x470) 12.5x9.
JAM DETECTION The display represents the top tray and the paper path area. When part of the mimic is illuminated, there is a problem in this area. Top tray If the top tray area is illuminated, you have to open the top cover to check the area and clear the problem. Paper path If the paper path area is illuminated, you have to open the top cover to check the area and clear the problem. This window is blinking when the machine does a set-up, and lighted when the machine is ready.
HOW TO PROGRAM A JOB (ROTATION OR REGISTRATION)? Refer to printer user interface, not available on XIM. Functions to be programmed: - Rotation/No rotation. - Centered or edge registered output. - Higher or lower exit selection...
JAM CLEARANCE - JOB RECOVERY - Location of the baffles 1 4 2 3 5 1 4 2 3 5 Operator Manual Page 9 - 12 Initial issue: 02/03 Latest revision: 10/03
TROUBLESHOOTING Problem Green power window not illuminated Cause No power Solution • Check that the power cord is connected to the wall outlet • Check if printer is ready • Check communication cable from Docutech 120 to XIM for proper connection • Check for other area if the mimic not illuminated • Check the service switch position (see "description of the machine" chapter) High paper curl • Adjust printer decurler • Flip paper in printer paper tray Mechanical obstruction • Check for obstruction in t
This page is intentionally left blank.
