User guide
Table Of Contents
- Table of contents
- Introduction
- System overview of the 4635 LPS
- Using the PC UI
- Paper facts
- System control tasks
- Job control tasks
- Online printing tasks
- Offline printing tasks
- UNKNOWN
- Power on the open-reel tape drive
- Load an open-reel tape
- Load an open-reel tape by hand
- Unload an open-reel tape
- Unload an open-reel tape during a power failure
- Handle open-reel tapes
- Power on the 18 track 1/2 inch cartridge tape drive
- Unload a 1/2 inch cartridge
- Power off the 18/36 track 1/2 inch tape drive
- Handle cartridge tapes
- Load a 1/4 inch cartridge tape
- Handle 1/4 inch cartridge tapes
- Load a floppy disk
- Handle floppy disks
- Start an offline print job
- Rewind/unload tape
- Space
- Move
- UNKNOWN
- HIP printing tasks
- Status and print tasks
- File control tasks
- Maintenance tasks
- Precautions you should take
- Cleaning supplies
- Maintaining the printer
- Replacing the dry ink cartridge
- Replacing the dry ink waste container
- Adding fuser agent
- Cleaning the sensors and the reflecting surfaces
- Tape drive cleaning schedule
- Cleaning precautions—READ BEFORE CLEANING
- Cleaning procedures
- When to clean the tape drive
- Cleaning procedures
- How to clean the floppy disk drive
- Installing the custom transfer assist blade
- Setting tray size with the custom transfer assist blades
- Problem solving tasks
- LPS problems
- Printing problems
- Paper jams
- Incorrect paper size message
- Stacker bin problems
- System controller problems
- Tape drive does not perform self-load routine
- “OK” appears on the tape drive message display, but the loading door is closed
- Basic recovery procedure
- Initial program load (IPL) procedure fails
- You cannot insert a cartridge
- Tape does not unload
- Unloading a cartridge after a power failure
- Tape winds completely out of cartridge
- Message display is blank
- Tape drive does not become ready
- LPS problems
- MICR operating procedures
- Bar code operating procedures
- A. Meter reading and reporting
- B. Supplies
- Glossary
- Index
PAPER FACTS
Table 3-6. Stacker bin performance guide
Paper Superior performance Good performance
Performance limits and
suggested alternatives
Size range* 8 by 10 to 11.69 by 17
inches/203 by 254 to 297 by
432 mm.
Smaller or larger sizes
cannot be used.
Weight range 20 to 110 pounds/75 to 200
gsm
Lighter than 20 pounds/75
gsm and no lighter than 16
pounds/60 gsm
Weights outside the limits
shown here are not
recommended.
Capacity • Capacity automatically
limited so stack weight
will not exceed 30
lbs/13.g kg
• Selectable with bin
capacity programming
(Refer to the “Bin full
criteria and setting bin
limits” section of chapter
9, “Status and print
tasks,” for instructions.
Stack quality • Xerographic paper in
good condition
• 20 pound/75 gsm and
heavier stock
• Very low to no output
curl
• Lighter weight stocks
with low output curl
• Intermixed stocks
• Adjust process decurler
• Flip paper in paper
feeders
• Limit stack capacity to
acceptable limits.
Type or
condition
• Xerographic paper in
good condition
• Predrilled stock
• No cut-outs, perforated
or intermixed weights
• Labels, preprinted forms,
perforated stocks
• Intermixed weights
• High output curl stocks
can cause severe stack
quality problems
• Tab stock intermixed
with smaller stocks
results in degraded stack
quality
• Reinforced mylar should
be limited to small stacks
of 200 sheets or less or
sent to the sample tray.
* Optional 7 X 10 enablement kit allows 7 by 10 inches/178 by
254 mm paper size.
3-16 XEROX 4635 LASER PRINTING SYSTEM OPERATOR GUIDE