User guide
Table Of Contents
- Table of contents
- Introduction
- System overview of the 4635 LPS
- Using the PC UI
- Paper facts
- System control tasks
- Job control tasks
- Online printing tasks
- Offline printing tasks
- UNKNOWN
- Power on the open-reel tape drive
- Load an open-reel tape
- Load an open-reel tape by hand
- Unload an open-reel tape
- Unload an open-reel tape during a power failure
- Handle open-reel tapes
- Power on the 18 track 1/2 inch cartridge tape drive
- Unload a 1/2 inch cartridge
- Power off the 18/36 track 1/2 inch tape drive
- Handle cartridge tapes
- Load a 1/4 inch cartridge tape
- Handle 1/4 inch cartridge tapes
- Load a floppy disk
- Handle floppy disks
- Start an offline print job
- Rewind/unload tape
- Space
- Move
- UNKNOWN
- HIP printing tasks
- Status and print tasks
- File control tasks
- Maintenance tasks
- Precautions you should take
- Cleaning supplies
- Maintaining the printer
- Replacing the dry ink cartridge
- Replacing the dry ink waste container
- Adding fuser agent
- Cleaning the sensors and the reflecting surfaces
- Tape drive cleaning schedule
- Cleaning precautions—READ BEFORE CLEANING
- Cleaning procedures
- When to clean the tape drive
- Cleaning procedures
- How to clean the floppy disk drive
- Installing the custom transfer assist blade
- Setting tray size with the custom transfer assist blades
- Problem solving tasks
- LPS problems
- Printing problems
- Paper jams
- Incorrect paper size message
- Stacker bin problems
- System controller problems
- Tape drive does not perform self-load routine
- “OK” appears on the tape drive message display, but the loading door is closed
- Basic recovery procedure
- Initial program load (IPL) procedure fails
- You cannot insert a cartridge
- Tape does not unload
- Unloading a cartridge after a power failure
- Tape winds completely out of cartridge
- Message display is blank
- Tape drive does not become ready
- LPS problems
- MICR operating procedures
- Bar code operating procedures
- A. Meter reading and reporting
- B. Supplies
- Glossary
- Index
PAPER FACTS
Table 3-4. Two-sided (duplex) printing performance guide
Paper Superior performance Good performance
Performance limits and
suggested alternatives
Size range*** 8 by 10 to 11.69 by 17
inches/203 by 254 to 297 by
432 mm.
Smaller or larger sizes
cannot be used.
Weight range 20 to 110 pounds/75 to 200
gsm****
Weights outside the limits
shown are not
recommended. If show
through occurs, adjust print
quality or use heavier weight
paper.
Type or
condition
• Xerographic paper in
good condition
• Predrilled stock
(fanned thoroughly)
• Slightly curled paper*
• Paper with reinforced
binding edges
• Tabs
Refer to the Paper Stocks
Guide for additional
information.
• Excessively curled
paper*
Avoid:
• Transparencies
Stock not defined here
is included in the Paper
Stocks Guide, which
follows.
* Curl direction should be determined before loading
paper into trays. Refer to the “Paper jams and paper
curl” section of chapter 12, “Problem solving tasks,” for
additional information.
** Refer to the Paper stocks guide for additional
information.
*** Optional 7 X 10 enablement kit allows 7 by 10 inches/178
by 254 mm paper size.
**** Make sure that heavy weight paper levers (located in
areas 2 and 4 of the printer) are in the appropriate
position for the weight of paper being used. Refer to
the “Prints are skewed“ section of the “Problem solving
tasks“ chapter.
XEROX 4635 LASER PRINTING SYSTEM OPERATOR GUIDE 3-5