User guide
Table Of Contents
- Table of contents
- Introduction
- System overview of the 4635 LPS
- Using the PC UI
- Paper facts
- System control tasks
- Job control tasks
- Online printing tasks
- Offline printing tasks
- UNKNOWN
- Power on the open-reel tape drive
- Load an open-reel tape
- Load an open-reel tape by hand
- Unload an open-reel tape
- Unload an open-reel tape during a power failure
- Handle open-reel tapes
- Power on the 18 track 1/2 inch cartridge tape drive
- Unload a 1/2 inch cartridge
- Power off the 18/36 track 1/2 inch tape drive
- Handle cartridge tapes
- Load a 1/4 inch cartridge tape
- Handle 1/4 inch cartridge tapes
- Load a floppy disk
- Handle floppy disks
- Start an offline print job
- Rewind/unload tape
- Space
- Move
- UNKNOWN
- HIP printing tasks
- Status and print tasks
- File control tasks
- Maintenance tasks
- Precautions you should take
- Cleaning supplies
- Maintaining the printer
- Replacing the dry ink cartridge
- Replacing the dry ink waste container
- Adding fuser agent
- Cleaning the sensors and the reflecting surfaces
- Tape drive cleaning schedule
- Cleaning precautions—READ BEFORE CLEANING
- Cleaning procedures
- When to clean the tape drive
- Cleaning procedures
- How to clean the floppy disk drive
- Installing the custom transfer assist blade
- Setting tray size with the custom transfer assist blades
- Problem solving tasks
- LPS problems
- Printing problems
- Paper jams
- Incorrect paper size message
- Stacker bin problems
- System controller problems
- Tape drive does not perform self-load routine
- “OK” appears on the tape drive message display, but the loading door is closed
- Basic recovery procedure
- Initial program load (IPL) procedure fails
- You cannot insert a cartridge
- Tape does not unload
- Unloading a cartridge after a power failure
- Tape winds completely out of cartridge
- Message display is blank
- Tape drive does not become ready
- LPS problems
- MICR operating procedures
- Bar code operating procedures
- A. Meter reading and reporting
- B. Supplies
- Glossary
- Index
SYSTEM OVERVIEW OF THE 4635 LASER PRINTING SYSTEM
Printer configurations
The 4635/4635MX LPS is available in the following five
configurations:
1. Printer + Inverter Feeder Stacker + Feeder Stacker
2. Printer + Inverter Feeder Stacker + Feeder Stacker + Bypass
Transport
3. Printer + Inverter Feeder Stacker + Feeder Stacker + Feeder
Stacker
4. Printer + Inverter Feeder Stacker + Feeder Stacker + Feeder
Stacker + Bypass Transport
5. Printer + Inverter Feeder Stacker + Feeder Stacker + Feeder
Stacker + Feeder Stacker
Each of these configurations can have the following printer
options:
• 7X10 enablement kit
• Bar code device
• Input enablement device
Notes:
• The input enablement device is not available on the last
configuration: Printer + Inverter Feeder Stacker + three
Feeder Stackers.
• Each of the configurations and options above is available
with the 4635MX system.
Refer to the “Printer options“ section earlier in this chapter for
information about each of the options above.
Figures 1-18 through 1-22 illustrate each of the five printer
configurations available.
Note: Figures 1-18 through 1-22 show the 4635 LPS with the
optional bar code device.
Figure 1-18. Printer + Inverter Feeder Stacker + Feeder
Stacker
XEROX 4635 LASER PRINTING SYSTEM OPERATOR GUIDE 1-19