User guide
Table Of Contents
- Table of contents
- Introduction
- System overview of the 4635 LPS
- Using the PC UI
- Paper facts
- System control tasks
- Job control tasks
- Online printing tasks
- Offline printing tasks
- UNKNOWN
- Power on the open-reel tape drive
- Load an open-reel tape
- Load an open-reel tape by hand
- Unload an open-reel tape
- Unload an open-reel tape during a power failure
- Handle open-reel tapes
- Power on the 18 track 1/2 inch cartridge tape drive
- Unload a 1/2 inch cartridge
- Power off the 18/36 track 1/2 inch tape drive
- Handle cartridge tapes
- Load a 1/4 inch cartridge tape
- Handle 1/4 inch cartridge tapes
- Load a floppy disk
- Handle floppy disks
- Start an offline print job
- Rewind/unload tape
- Space
- Move
- UNKNOWN
- HIP printing tasks
- Status and print tasks
- File control tasks
- Maintenance tasks
- Precautions you should take
- Cleaning supplies
- Maintaining the printer
- Replacing the dry ink cartridge
- Replacing the dry ink waste container
- Adding fuser agent
- Cleaning the sensors and the reflecting surfaces
- Tape drive cleaning schedule
- Cleaning precautions—READ BEFORE CLEANING
- Cleaning procedures
- When to clean the tape drive
- Cleaning procedures
- How to clean the floppy disk drive
- Installing the custom transfer assist blade
- Setting tray size with the custom transfer assist blades
- Problem solving tasks
- LPS problems
- Printing problems
- Paper jams
- Incorrect paper size message
- Stacker bin problems
- System controller problems
- Tape drive does not perform self-load routine
- “OK” appears on the tape drive message display, but the loading door is closed
- Basic recovery procedure
- Initial program load (IPL) procedure fails
- You cannot insert a cartridge
- Tape does not unload
- Unloading a cartridge after a power failure
- Tape winds completely out of cartridge
- Message display is blank
- Tape drive does not become ready
- LPS problems
- MICR operating procedures
- Bar code operating procedures
- A. Meter reading and reporting
- B. Supplies
- Glossary
- Index
GLOSSARY
GLOSSARY-8 XEROX 4635 LASER PRINTING SYSTEM OPERATOR GUIDE
mouse Electronic device used with the PC UI to select options and enter
data.
network 1. System of geographically separate computers, linked to one
another over transmission lines. 2. Communication lines
connecting a computer to its remote terminals.
object mode For the 4635 LPS, the processing method of the PC UI which
uses the mouse, windows, and icons. The PC UI operates in
either the object mode or in the terminal emulation mode (TEM).
See also TEM.
offline Devices not under the active control of a central processing unit.
For example, a computer makes output to a magnetic tape. The
tape is then used by an offline printing system to produce
printed data. Offline operations are much slower than online
operations. See also online.
offset To place pages currently being printed in slightly different
positions from previous pages.
online Devices under the direct control of a central processing unit, for
example a printing system in interactive communication with a
mainframe. See also offline.
orientation 1. In reference to image area, orientation describes whether the
printed lines are parallel to the long edge of the paper or the
short edge of the paper. 2. Choice of printing portrait
(vertically) or landscape (horizontally).
origin In reference to image area, this is the upper left corner of a
sheet.
page detail Non printable customer encoded data used to describe each
audited page of a report. Page details are used to create
4635MX audit files.
page orientation See orientation.
parameter Part of a command, other than the keyword. See also keyword;
operator command.
pass-through job On systems with XPAF, a job that is sent directly from a host to a
Xerox printer using XPAF, without undergoing XPAF processing.
PC UI PC user interface. The PC hardware and Xerox-supplied software
which allows the operator to control the LPS by means of a
mouse, windows, and icons. See also object mode; TEM.