User guide
Table Of Contents
- Table of contents
- Introduction
- System overview of the 4635 LPS
- Using the PC UI
- Paper facts
- System control tasks
- Job control tasks
- Online printing tasks
- Offline printing tasks
- UNKNOWN
- Power on the open-reel tape drive
- Load an open-reel tape
- Load an open-reel tape by hand
- Unload an open-reel tape
- Unload an open-reel tape during a power failure
- Handle open-reel tapes
- Power on the 18 track 1/2 inch cartridge tape drive
- Unload a 1/2 inch cartridge
- Power off the 18/36 track 1/2 inch tape drive
- Handle cartridge tapes
- Load a 1/4 inch cartridge tape
- Handle 1/4 inch cartridge tapes
- Load a floppy disk
- Handle floppy disks
- Start an offline print job
- Rewind/unload tape
- Space
- Move
- UNKNOWN
- HIP printing tasks
- Status and print tasks
- File control tasks
- Maintenance tasks
- Precautions you should take
- Cleaning supplies
- Maintaining the printer
- Replacing the dry ink cartridge
- Replacing the dry ink waste container
- Adding fuser agent
- Cleaning the sensors and the reflecting surfaces
- Tape drive cleaning schedule
- Cleaning precautions—READ BEFORE CLEANING
- Cleaning procedures
- When to clean the tape drive
- Cleaning procedures
- How to clean the floppy disk drive
- Installing the custom transfer assist blade
- Setting tray size with the custom transfer assist blades
- Problem solving tasks
- LPS problems
- Printing problems
- Paper jams
- Incorrect paper size message
- Stacker bin problems
- System controller problems
- Tape drive does not perform self-load routine
- “OK” appears on the tape drive message display, but the loading door is closed
- Basic recovery procedure
- Initial program load (IPL) procedure fails
- You cannot insert a cartridge
- Tape does not unload
- Unloading a cartridge after a power failure
- Tape winds completely out of cartridge
- Message display is blank
- Tape drive does not become ready
- LPS problems
- MICR operating procedures
- Bar code operating procedures
- A. Meter reading and reporting
- B. Supplies
- Glossary
- Index
PROBLEM SOLVING TASKS
3. Relatch the paper feeder assembly by pressing down on the
bright green dot. Slide the paper tray completely back into
the printer.
Figure 12-33. Relatching the paper feeder assembly
4. Operate the system as usual. If you are still experiencing
misfeeds, place a service call.
Notes:
1. This procedure should be used only to correct a
problem, not as a routine maintenance procedure.
Because the belts are made of rubber, frequent cleaning
with film remover will dry them out and cause them to
fail prematurely.
2. Film remover may be obtained from your Xerox service
representative.
Faults are cleared but the Attention light is still on
If you have cleared all faults that are listed on the printer control
console, but the Attention light is still on and the message
“Output is stopped. See message at the System Display” appears
on the printer control console, there may be an uncleared output
fault. Check the PC UI Command Line/Message window or an
opened window for an output message (preceded by an asterisk
and OS followed by a number). Follow the instructions in the
output message and press the Continue button.
Printing does not continue when the Continue button is pressed
If the Continue button is pressed before all printer faults are
cleared, the outstanding faults are changed to the status of
masked faults (refer to the “Fault masking and the printer control
console” section earlier in this chapter). If the printer status
displayed in the message area of the printer control console is
READY, but printing does not continue when you press the
Continue button, touch the Fault List icon on the printer control
console to display the Fault List screen. (Refer to figure 12-1.)
Clear any faults displayed on this screen and press the Continue
button again.
XEROX 4635 LASER PRINTING SYSTEM OPERATOR GUIDE 12-25