User guide
Table Of Contents
- Table of contents
- Introduction
- System overview of the 4635 LPS
- Using the PC UI
- Paper facts
- System control tasks
- Job control tasks
- Online printing tasks
- Offline printing tasks
- UNKNOWN
- Power on the open-reel tape drive
- Load an open-reel tape
- Load an open-reel tape by hand
- Unload an open-reel tape
- Unload an open-reel tape during a power failure
- Handle open-reel tapes
- Power on the 18 track 1/2 inch cartridge tape drive
- Unload a 1/2 inch cartridge
- Power off the 18/36 track 1/2 inch tape drive
- Handle cartridge tapes
- Load a 1/4 inch cartridge tape
- Handle 1/4 inch cartridge tapes
- Load a floppy disk
- Handle floppy disks
- Start an offline print job
- Rewind/unload tape
- Space
- Move
- UNKNOWN
- HIP printing tasks
- Status and print tasks
- File control tasks
- Maintenance tasks
- Precautions you should take
- Cleaning supplies
- Maintaining the printer
- Replacing the dry ink cartridge
- Replacing the dry ink waste container
- Adding fuser agent
- Cleaning the sensors and the reflecting surfaces
- Tape drive cleaning schedule
- Cleaning precautions—READ BEFORE CLEANING
- Cleaning procedures
- When to clean the tape drive
- Cleaning procedures
- How to clean the floppy disk drive
- Installing the custom transfer assist blade
- Setting tray size with the custom transfer assist blades
- Problem solving tasks
- LPS problems
- Printing problems
- Paper jams
- Incorrect paper size message
- Stacker bin problems
- System controller problems
- Tape drive does not perform self-load routine
- “OK” appears on the tape drive message display, but the loading door is closed
- Basic recovery procedure
- Initial program load (IPL) procedure fails
- You cannot insert a cartridge
- Tape does not unload
- Unloading a cartridge after a power failure
- Tape winds completely out of cartridge
- Message display is blank
- Tape drive does not become ready
- LPS problems
- MICR operating procedures
- Bar code operating procedures
- A. Meter reading and reporting
- B. Supplies
- Glossary
- Index
TABLE OF CONTENTS
Rasterization messages 12-28
Power failure 12-28
Status file nearly full message 12-29
Open-reel tape drive problems 12-30
Tape drive does not perform self-load routine 12-30
“OK“ appears on the tape drive message display, but
the loading door is closed 12-31
“LID OPEN“ appears on the tape drive message display 12-31
1/2 inch cartridge tape drive problems 12-32
Basic recovery procedure 12-32
Initial program load (IPL) procedure fails 12-32
You cannot insert a cartridge 12-33
Tape does not unload 12-33
Unloading a cartridge after a power failure 12-34
Tape winds completely out of cartridge 12-34
Message display is blank 12-34
Tape drive does not become ready 12-35
Calling for service 12-35
13. MICR operating procedures 13-1
Overview 13-1
Features of the 4635MX system 13-1
MICR materials 13-2
Turning MICR mode on or off 13-2
MICR mode echo 13-3
Should MICR be turned off or on? 13-3
Points regarding MICR mode and the system UI 13-3
MICR mode following a sysgen 13-3
MICR output 13-4
Tools to check MICR output 13-5
MICR position and dimension gauge 13-5
8 power (X) comparator with MICR grid 13-6
Adding dry ink 13-6
14. Bar code operating procedures 14-1
Introduction 14-1
Laser safety 14-1
Turning bar code on or off 14-1
Bar code mode echo 14-3
Adjusting the bar code reader 14-4
xiv XEROX 4635 LASER PRINTING SYSTEM OPERATOR GUIDE