User guide
Table Of Contents
- Table of contents
- Introduction
- System overview of the 4635 LPS
- Using the PC UI
- Paper facts
- System control tasks
- Job control tasks
- Online printing tasks
- Offline printing tasks
- UNKNOWN
- Power on the open-reel tape drive
- Load an open-reel tape
- Load an open-reel tape by hand
- Unload an open-reel tape
- Unload an open-reel tape during a power failure
- Handle open-reel tapes
- Power on the 18 track 1/2 inch cartridge tape drive
- Unload a 1/2 inch cartridge
- Power off the 18/36 track 1/2 inch tape drive
- Handle cartridge tapes
- Load a 1/4 inch cartridge tape
- Handle 1/4 inch cartridge tapes
- Load a floppy disk
- Handle floppy disks
- Start an offline print job
- Rewind/unload tape
- Space
- Move
- UNKNOWN
- HIP printing tasks
- Status and print tasks
- File control tasks
- Maintenance tasks
- Precautions you should take
- Cleaning supplies
- Maintaining the printer
- Replacing the dry ink cartridge
- Replacing the dry ink waste container
- Adding fuser agent
- Cleaning the sensors and the reflecting surfaces
- Tape drive cleaning schedule
- Cleaning precautions—READ BEFORE CLEANING
- Cleaning procedures
- When to clean the tape drive
- Cleaning procedures
- How to clean the floppy disk drive
- Installing the custom transfer assist blade
- Setting tray size with the custom transfer assist blades
- Problem solving tasks
- LPS problems
- Printing problems
- Paper jams
- Incorrect paper size message
- Stacker bin problems
- System controller problems
- Tape drive does not perform self-load routine
- “OK” appears on the tape drive message display, but the loading door is closed
- Basic recovery procedure
- Initial program load (IPL) procedure fails
- You cannot insert a cartridge
- Tape does not unload
- Unloading a cartridge after a power failure
- Tape winds completely out of cartridge
- Message display is blank
- Tape drive does not become ready
- LPS problems
- MICR operating procedures
- Bar code operating procedures
- A. Meter reading and reporting
- B. Supplies
- Glossary
- Index
TABLE OF CONTENTS
Cleaning procedures 11-17
Access to the tape path 11-17
Cleaning the tape path 11-18
Cleaning the exterior of the tape path 11-18
Cleaning the 1/2 inch cartridge tape drive 11-19
When to clean the tape drive 11-19
Cleaning procedures 11-19
Cleaning the tape path 11-19
Cleaning a cartridge 11-19
Cleaning the 1/4 inch cartridge tape drive 11-20
Cleaning the floppy disk drive 11-20
How to clean the floppy disk drive 11-20
Using the custom transfer assist blade 11-22
When not to use the custom transfer assist blade 11-22
Installing the custom transfer assist blade 11-23
Setting tray size with the custom transfer assist blades 11-23
12. Problem solving tasks 12-1
LPS problems 12-1
Fault masking and the printer control console 12-1
Printing problems 12-3
Prints are skewed or damaged 12-3
Paper jams 12-5
Paper curl and paper jams 12-6
Aids to paper jam clearance 12-8
Clearing area paper jams 12-8
Checking job integrity following a paper jam 12-9
Printer areas 12-10
Clearing a misfeed (feeder tray fault) 12-21
Frequent misfeeds (processor feeder trays) 12-23
Faults are cleared but the Attention light is still on 12-25
Printing does not continue when the Continue button
is pressed 12-25
Incorrect paper size message 12-26
Stacker bin problems 12-26
Papers are being thrown around the stacker 12-26
Paper stack is falling over or sliding around the bin 12-26
System controller problems 12-26
LPS does not boot (system controller terminal) 12-26
Printer does not respond to system controller 12-27
Blank display (system controller terminal) 12-28
XEROX 4635 LASER PRINTING SYSTEM OPERATOR GUIDE xiii