Software Version 10.
©2010 Xerox Corporation. All rights reserved. XEROX® and XEROX and Design®, Xerox Nuvera® and FreeFlow® are trademarks of Xerox Corporation in the United States and/or other countries. Changes are periodically made to this document. Technical inaccuracies and typographic errors will be corrected in subsequent editions. Document Version: 10.2 (May 21, 2010).
Table of Contents Preface....................................................................................................................... v General Purpose and Audience .......................................................................................................v 1 2 3 Software Versions....................................................................................1-1 New Capabilities in Version 10.2 Software....................................2-1 Release Issues ......................
Preface General Purpose and Audience This document for the Xerox Nuvera contains the following information: • Software release deliverables and version numbers • New features in this release • Issues resolved in this release • New issues present in this release • Known operating limitations that are to be resolved in a future release Standard system operating procedures and information can be found in the following documentation: • For specific information about system operations, performance and
Preface Xerox Nuvera [This page left intentionally blank] vi Hints and Tips Guide
1 Software Versions 1 This document references the following software versions: Item Version Number Free Flow Print Server 7.0 SP3 / Tigris System software RV.9.2.24.xx IPDS (must match DocuSP version) CP.73A1.31 FreeFlow Print Server 7.0 SP3 Remote Workflow * CP. 73A1.14 (English) FreeFlow Print Server 7.0 SP3 and Variable Input version FreeFlow Print Server 7.0 SP1 Includes Variable Input (VI) and Variable Print Manager (VPM) version 5.0.
2 New Capabilities in Version 10.2 Software 2 The following is a list of new capabilities enabled with version 10.2 software: 1. 2. 3. 4. 5. 6. 7. The Xerox Tape Binder (XTB) is now configurable in Dual Mode (2 XTB’s connected together). Disable status messages when trays are disabled. This de-clutters the status message area when a tray is disabled. Add a custom edge erase feature that can set the edge erase in the range of 0 mm to 6 mm for each of the four edges.
3 Release Issues 3 Issues resolved The following is a list of Nuvera 10.1 issues that have been resolved and no longer apply to Xerox Nuvera 10.
Release Issues Xerox Nuvera Issues remaining from previous release CQ#45919 Tray Programming Reverts to Default Settings Description When 'After Every Tray Cycle' tray confirmation is enabled, and a tray is cycled, all tray programming, except for Stock Size, in the pop-up confirmation window is set to default.
Xerox Nuvera Release Issues CQ#43522 Annotation-2 Description When performing a “Copy and Save” or “Print and Save” operation with annotations turned on, the reprint of the saved job will be unreadable. Workaround Perform a “Save” operation and then “Print” the saved job. CQ#44256 Configuration Backup Description When performing a Configuration Backup, make sure you do not exceed the maximum disk size of the CD. If you do, the backup will fail without an indication as to why. Workaround None.
Release Issues Xerox Nuvera CQ#38117 Short Edge Feed 9x11 Stock Description 9 x 11 stock cannot be loaded short edge first (SEF). Workaround Load an SEF-only stock such as Legal, run one or more sheets on that stock, then unload it and put in 9x11 S CQ#26871 Queue and Job based subsetting fails for Odd number of pages duplex jobs Description Subset offset and finishing can be programmed on job in the job manager or on a Queue. This works fine for simplex jobs.
Xerox Nuvera Release Issues CQ#46849 Message stating 'The online configuration file online.config does not exist' when closing the 'Gateways' Description The above error message may occur when closing the “Gateways” window in the Online Setup tab. Workaround If this occurs, select OK in the error message and then close or Cancel in the gateways window.
Release Issues Xerox Nuvera When exiting MICR Mode, the Edge erase remains at no erase Description When exiting MICR Mode, the edge erase setting will remain at “none”. We leave it to the user to set the edge erase to the values they want. Workaround Do not forget to set the edge erase to desired setting after exiting MICR Mode.
