Model 76667G "Surf N Swing'in" Swing Set with Galvanized Frame Assembled dimensions are 179" x 102" x 74" Allow 6 - 12 ft of clearance around the perimeter of the swing set area when fully assembled. OWNER'S MANUAL, ASSEMBLY INSTRUCTIONS, CARE, MAINTENANCE AND USER'S GUIDE Important Instructions & Warnings! Please read this entire instruction and assembly manual completely before proceeding. You must follow all safety instructions while using this equipment.
IMPORTANT INSTRUCTIONS AND WARNINGS WARNING READ ALL INSTRUCTIONS BEFORE ASSEMBLING OR USING THIS EQUIPMENT AGE & WEIGHT LIMIT This product is designed to be used by up to six (6) children between the ages of 3 to 8. Maximum user weight is 100 pounds (45 kg) each with a combined maximum weight of 600 pounds (273 kgs). The play set is designed for children over three (3) years of age up to (8) years of age. Use by smaller children can result in entrapment.
Do not install your play set over hard surface, e.g. asphalt, concrete, packed earth, tile or brick floor. A fall onto a hard surface can result in serious injury or death to the user.
PLAY SUPERVISION DO NOT allow more than one child to play on the individual swing, stand R swing, or slide component at any one time. DO NOT allow children to stand on the slide, swing seats, see-saw, rocky-rider, stand n swing, or glide ride. DO NOT allow children to walk too close to moving parts. ALWAYS keep a safe distance to avoid being struck by other children while playing on swings, slides, trapeze, glide ride, etc.
INSPECTION PRIOR TO EACH USE OR DAILY INSPECTION DO NOT use the equipment if any bolts or nuts are missing or loose. ALWAYS check to ensure the equipment and all parts are well secured and stable before each use. ALWAYS clear the play area of any rocks, sharp objects, or any materials that could be potentially hazardous to users.
ANCHORING (NOTE:ANCHORS ARE NOT INCLUDED-MUST BE PURCHASED SEPARATELY) There are different ways of anchoring the equipment, depending on the type of ground on which the equipment is to be installed. Make sure that all anchors are below ground level to prevent tripping. You should consult your local contractor to decide the most appropriate way to anchor the equipment in your location.
FRAME LEG 12-5/8” CONCRETE 5” 2” BRICK OR GRAVEL BED Note: The maximum fall height for this product is 4 feet. The minimum ground clearance between the bottom of the suspended plays and the playing or ground surface must be 8 inches. You must maintain a minimum of 8 inches of ground clearance. WARNING Please properly anchor the swing set to minimize the risk of injury or death. If the swing set is used without proper anchoring, it may be dangerous and may tilt over.
CARE AND MAINTENANCE CHECKLIST AT THE BEGINNING OF EACH PLAY SEASON: Tighten all hardware. Lubricate all metallic moving parts. Check all protective coverings on bolts, pipes, edges, and corners. Replace if they are loose, cracked, or missing. Check all moving parts including swing seats and chains for wear, rust or other deterioration. Replace as needed. Check metal parts for rust. If found, sand and repaint using a non-lead paint meeting the requirements of 16 CFR 1303.
TOOLS NEEDED Please prepare the following tools prior to assembling this equipment. Special Socket Wrench (Not Included) Hammer (If you intend to install anchor, this is needed) Wrench (Not Included) Flat Head and Philips Head Screwdriver (Not included) Small Allen Wrench （Not Included) Tape Measure (Not included) Wrench (Included) Medium Allen Wrench (Included) Big Allen Wrench (Included) Scissors (Not included) DO NOT RETURN TO RETAILER YOU PURCHASED AT. CONTACT XDP FOR PARTS AND SUPPORT AT 1.
Part list for main frame assembly A1 LEFT TOP BAR 1 A2 MIDDLE TOP BAR 1 1 A3 MIDDLE TOP BAR 2 1 A4 MIDDLE TOP BAR 3 1 A5 RIGHT TOP BAR 1 A7 TOP SECTION LEG 6 A8 BOTTOM SECTION LEG WITH FOAM 6 A10 LEG (WITH TWO HOLES) 2 A11 CROSS BAR (WITH FOUR HOLES) 1 Hardware used for main frame assembly B1 BOLT 5/16"x63mm 14 B2 BOLT 5/16"x68mm 6 B3 NUT 5/16" 20 B4 PLASTIC CAP (WITH ARC WASHER) 20 B5 ARC WASHER 5/16” 14 B6 WASHER 5/16” 6 Part list for swing seat assembly J1 J3
Hardware used for swing seat assembly J6 NUT 5/16’’ 4 J7 WASHER 5/16’’ 2 J8 PLASTIC CAP (WITH ARC WASHER) 2 J9 PLASTIC CAP (WITH FLAT WASHER) 2 Part list for Stand R Swing assembly J1A PVC COVERED CHAIN (PRE-ASSEMBLED) 2 J3A EYE BOLT WITH ATTACHMENT BOLT (PRE-ASSEMBLED ON J1A) 2 J3A-N K2 EYE BOLT WITH ATTACHMENT BOLT (PRE-ASSEMBLED ON J1A) 2 STAND R SWING 1 Hardware used for Stand R Swing assembly J6A NUT 5/16" 4 J7A WASHER 5/16" 2 J8A PLASTIC CAP (WITH ARC WASHER) 2 J9A PL
R3-1 DISC SWING TUBE FOAM (PRE-ASSEMBLED ON R3-N) 4 R4-N DISC SWING FABRIC 1 Hardware used for SUPER DISC (TM) Swing assembly F1-N NUT 5/16" 6 F2-N ARC WASHER 4 F3-N PLASTIC CAP (WITH ARC WASHER) 2 Part list for Surf N Swing assembly S1 ATTACHMENT BOLT (PRE-ASSEMBLED ON S2) 2 S2 Rope set (PRE-ASSEMBLED) 2 S3 FOOTREST SUPPORT 2 S4 EYE BOLT (PRE-ASSEMBLED ON S2) 4 S5 SURF N SWING 1 X9 SUPPORT 2 Hardware used for Surf N Swing assembly S7 NUT 5/16" 6 S10 WASHER 5/16" 4 S11
Part list for slide assembly X1-N SLIDE SUPPORT (WITH OPENING) 1 X2-N SLIDE SUPPORT 1 X3-N SLIDE LEG TUBE 2 X4-N SLIDE TOP SUPPORT BAR 1 X5-N SLIDE FRONT SUPPORT 1 X6 SLIDE LADDER STEPS 2 X7-N SUPPORT A 2 X8-N SUPPORT B 2 Y3-1 SLIDE A 1 Y3-2 SLIDE B 1 Y3-3 SLIDE C 1 Y1 PLASTIC CONNECTOR 2 Z1 BOLT 1/4” (38mm) 6 Z2 BOLT 1/4” (75mm) 4 Z3 SPRING WASHER (large) 4 Z4 CAP NUT 1/4” 10 Z5 CAP BOLT 1/4” 4 Z6 SPRING WASHER (medium) 36 Z7 BOLT 1/4” (60mm) 4 Z8 B
ASSEMBLY INSTRUCTIONS Place the playground equipment on level ground and not less than 6ft (1.8m) from any structure or obstruction such as a fence, garage, house, overhanging branches, laundry line, or electrical wires. Do not install the playground equipment over concrete, asphalt, packed earth, or any other hard surface; a fall onto a hard surface can result in serious injury or death to the equipment user. Adequate overhead clearance is essential.
STEP 1 – Assemble the top bar frame of the swing set Connect A1、A2、A3、A4and A5,secure with B3, B4, B5 and B1 as shown below. Note: All round holes should be facing up and concave holes facing down. B3 B3 B3 B4 B3 B4 B4 B4 B5 B5 A2 A1 B5 A3 B5 B1 B1 A5 A4 B1 B1 DO NOT RETURN TO RETAILER YOU PURCHASED AT. CONTACT XDP FOR PARTS AND SUPPORT AT 1.866.884.0535 or service@xdp-recreation.
STEP 2 – Assemble the support legs of swing set Connect A1 to A7 and secure using B1, B5, B4 and B3 as shown below. Repeat the above step for the right side of the swing set (A3 & A5). A1 B4 B1 B5 B5 B1 B3 A7 A7 A8 A8 DO NOT RETURN TO RETAILER YOU PURCHASED AT. CONTACT XDP FOR PARTS AND SUPPORT AT 1.866.884.0535 or service@xdp-recreation.
STEP 3 – Attach the crossbar to the support legs Attach A10 to the outer side of A7 & A8and secure using B2, B6, B4 and B3. Repeat the above step for the middle side of the swing set (A3). A1 A7 A7 B6 B3 B4 B2 A10 B4 B3 B6 A8 B2 A8 DO NOT RETURN TO RETAILER YOU PURCHASED AT. CONTACT XDP FOR PARTS AND SUPPORT AT 1.866.884.0535 or service@xdp-recreation.
Attach A11 to the outer side of A7 and secure using B2, B6, B4 and B3. A5 A7 A7 B3 B6 B4 B2 B3 A8 A11 B4 B6 A8 B2 A5 A4 A7 A3 A7 A2 A1 A7 A11 A8 A7 A7 A10 A7 A8 A8 A10 A8 A8 A8 DO NOT RETURN TO RETAILER YOU PURCHASED AT. CONTACT XDP FOR PARTS AND SUPPORT AT 1.866.884.0535 or service@xdp-recreation.
STEP 4- "SWING SEAT" Assembly (w. "Adjustable Height" Feature) Connect swing set chains to the top bar by inserting J3-N through A3, securing with J8 and J6 as shown in Diagram A. Connect swing seat to the chains by inserting J3 through K1 and secure with J7, J9 and J6 as shown in Diagram B. J6 J6 DIAGRAM A J8 A3 J3-N J3-N J1 J1 J3 J3 J3-N 1 4 3 2 5 DO NOT RETURN TO RETAILER YOU PURCHASED AT. CONTACT XDP FOR PARTS AND SUPPORT AT 1.866.884.0535 or service@xdp-recreation.
DIAGRAM B J1 J3 J1 J3 K1 J7 J7 J9 J9 J6 J6 Important that the ‘washer’ ( J7 ) is included in the seat assembly. DO NOT RETURN TO RETAILER YOU PURCHASED AT. CONTACT XDP FOR PARTS AND SUPPORT AT 1.866.884.0535 or service@xdp-recreation.
STEP 5 - "Stand R Swing" Seat Assembly (w. "Adjustable Height" Feature) Connect Stand R Swing chains to the top bar by inserting J3A-N through A4 and securing with J8A and J6A as shown in Diagram A. Connect Stand R Swing to the chains by inserting J3A through K2 and secure with J7A, J9A and J6A as shown in Diagram B. J6A DIAGRAM A J6A J8 A A4 J8A J3A-N J3A-N J1A J1A J3A J3A J3A-N 1 4 3 2 5 DO NOT RETURN TO RETAILER YOU PURCHASED AT. CONTACT XDP FOR PARTS AND SUPPORT AT 1.866.884.
DIAGRAM B J1A J3A J1A J3A K2 J7A J7A J9A J9A J6A J6A Important that the ‘washer’ ( J7A ) is included in the seat assembly. NOTE: 1. Do not over-tighten the nuts and bolts at every step. 2. Do not snap in the cover of plastic cap until you have finished the assembly of each step and went back to tighten all of the nuts and bolts. DO NOT RETURN TO RETAILER YOU PURCHASED AT. CONTACT XDP FOR PARTS AND SUPPORT AT 1.866.884.0535 or service@xdp-recreation.
STEP 6 –Super Disc (TM) Swing Assembly Separation of foam tube R3-1 from R3-N Insert the foam tube R3-1 into R4-N first, then insert R3-N into R3-1 in R4-N. Slide the smaller ends of R3-N tubes into the pockets of Super Disc (TM) Swing Fabric (R4-N). Connect the four tubes together. Align the holes with the round holes face down. R3-1 R3-N R3-1 R3-N R3-1 R4-N R3-N R4-N DO NOT RETURN TO RETAILER YOU PURCHASED AT. CONTACT XDP FOR PARTS AND SUPPORT AT 1.866.884.0535 or service@xdp-recreation.
STEP 7 – Attach Super Disc (TM) Swing to the Swing Set Frame Connect the chain (R1-N) to the Super Disc (TM) Swing by inserting R2B-N and securing with F2-N and F1-N as shown in Diagram A. Connect Super Disc (TM) Swing to the top bar by inserting R2A-N through A1 and A2, securing with F3-N and F1-N as shown in Diagram B DIAGRAM A R1-N R1-N R1-N R2B-N R2B-N R1-N R2B-N F2-N R2B-N F2-N F1-N R3-N F1-N F2-N F2-N F1-N F1-N DO NOT RETURN TO RETAILER YOU PURCHASED AT.
DIAGRAM B F1-N F3-N F1-N F3-N A2 A1 R2A-N R1-N R2B-N R2B-N NOTE: 1. Do not over-tighten the nuts and bolts at every step. 2. Do not snap in the cover of plastic cap until you have finished the assembly of each step and went back to tighten all of the nuts and bolts. DO NOT RETURN TO RETAILER YOU PURCHASED AT. CONTACT XDP FOR PARTS AND SUPPORT AT 1.866.884.0535 or service@xdp-recreation.
STEP 8 - Surf N Swing Assembly Put X9 into S5 and insert S3 to the S5 and X9 as shown in Diagram A. Note: The X9 should be positioned in the same direction as the groove of S5. DIAGRAM A X9 S5 S3 X9 S5 DO NOT RETURN TO RETAILER YOU PURCHASED AT. CONTACT XDP FOR PARTS AND SUPPORT AT 1.866.884.0535 or service@xdp-recreation.
Secure S4 to the S3 by using S7, S10 and S11 as shown in Diagram B. Insert S1 through the hole on A5 and Secure with S7 and S12 as shown in Diagram B. DIAGRAM B S7 A5 S7 S12 S12 S1 S1 S2 S10 S11 S7 S10 S11 S7 S4 S7 S4 S10 S10 S7 S11 S11 S5 NOTE: 1. Do not over-tighten the nuts and bolts at every step. 2. Do not snap in the cover of plastic cap until you have finished the assembly of each step and went back to tighten all of the nuts and bolts. DO NOT RETURN TO RETAILER YOU PURCHASED AT.
STEP 9 - Slide assembly Connect Y3-1, Y3-2 and Y3-3 secure with Z8 and Z6 as shown below. Please assure Z8 bolts are securely tightened. Z8 Z6 Z8 Z8 Z6 Z6 Z8 Z6 Y3-1 Y3-2 Y3-3 Z6 Z8 Z6 Z8 DO NOT RETURN TO RETAILER YOU PURCHASED AT. CONTACT XDP FOR PARTS AND SUPPORT AT 1.866.884.0535 or service@xdp-recreation.
Connect X7-N and X8-N with Z10、Z6 and Z9 as shown below. X7-N X8-N X7-N X8-N Z10 Z6 Z9 DO NOT RETURN TO RETAILER YOU PURCHASED AT. CONTACT XDP FOR PARTS AND SUPPORT AT 1.866.884.0535 or service@xdp-recreation.
STEP 10- Slide assembly Insert X5-N into the base of Y3-3. Secure using Z7, Z6 and Z4. Attach X4-N to Y3-1. Note: Make sure that the bolt holes face up. Y3-1 Y3-2 X4-N Z7 Z6 Bolt hole faces up. Z4 Y3-3 Z6 X5-N Z7 NOTE: 1. Do not over-tighten the nuts and bolts at every step. 2. Do not snap in the cover of plastic cap until you have finished the assembly of each step and went back to tighten all of the nuts and bolts. DO NOT RETURN TO RETAILER YOU PURCHASED AT.
STEP 11 - Slide assembly (continued) Attach X6 to X1-N and X2-N. The inner sides of both X2-N and X1-N, where X6 (slide ladder steps) is attached to, are with concave holes. Secure each side using Z1, Z6 and Z4. Attach X3-N to X1-N and X2-N. Align holes and hold in position. Narrow side (Direction as shown below) Front side X2-N Wide side faces the front direction of the slide X1-N Z1 Z6 Z4Z6 X3-N X6 Z4 Z1 Z6 Z6 X3-N NOTE: 1. Do not over-tighten the nuts and bolts at every step. 2.
STEP 12 - Slide assembly (continued) Secure the two sides of the slide using Z2, Z6 and Z4, in the sequence shown in the diagram. Attach X4-N to X1-N and X2-N; Secure using Z1, Z6, Z3 and Z5 as shown in the enlarged diagram. X4-N X2-N Z1 X1-N Z6 Z2 Z6 Z3 Z4 Z5 Z6 Y3-2 Z2 Z6 X1-N X3-N NOTE: 1. Do not over-tighten the nuts and bolts at every step. 2. Do not snap in the cover of plastic cap until you have finished the assembly of each step and went back to tighten all of the nuts and bolts.
STEP 13 - Slide assembly (continued) Fit Y1 in between X1-N and A11; Secure using Y1, Z2, Z6 and Z3, Z5. Z5 Z3 X1-N Y1 Z5 Z3 Z6 Z2 A11 A8 A8 NOTE: 1. Do not over-tighten the nuts and bolts at every step. 2. Do not snap in the cover of plastic cap until you have finished the assembly of each step and went back to tighten all of the nuts and bolts. DO NOT RETURN TO RETAILER YOU PURCHASED AT. CONTACT XDP FOR PARTS AND SUPPORT AT 1.866.884.0535 or service@xdp-recreation.
Congratulations! You have now completed the swing set assembly. Please make sure to thoroughly check all parts and hardware to make sure all bolts and nuts are well secured before using the playground equipment. WARNING - Do not let children use the playground equipment until it is properly assembled and anchored. DO NOT RETURN TO RETAILER YOU PURCHASED AT. CONTACT XDP FOR PARTS AND SUPPORT AT 1.866.884.0535 or service@xdp-recreation.
Thank you for your purchase of an XDP Recreation swing set. By following the instruction manual, reading all safety and assembly instructions, and properly anchoring your swing set in the ground, your kids will safely enjoy hours of fun. Detailed below is our warranty covering your purchase. Please be sure to read it and contact us in the event you need service or parts. DO NOT RETURN THE SET TO THE STORE YOU PURCHASED IT.
ADDENDUM - PRODUCT INFORMATION & SUPPORT Please Retain Sales Receipt for Warranty Purposes. DO NOT RETURN THE SET TO THE STORE. If replacement parts or IF Customer Service is needed please contact XDP Recreation by email at service@xdp-recreation.com or CALL 1-866-884-0535 between 8:00am and 5:00pm (Eastern Standard Time), Monday - Friday. This Swing Set is designed to be used safely by children, ages 3 years to 8 years, with weight capacity of 100 lbs per child.
Dear Customer, 2019 THANK YOU for being an XDP Recreation Customer. IT’S HERE – The NEW FIREFLY LED SWING Check out our Website or the General Marketplace For this FANTASTICALLY / FUN STROBING – LED – COLORED – FLASHING MODES SWING www.xdp-recreation.com KEEP HAVING FUN! www.xdp-recreation.com Alpharetta, Ga. 30005 USA DO NOT RETURN TO RETAILER YOU PURCHASED AT. CONTACT XDP FOR PARTS AND SUPPORT AT 1.866.884.0535 or service@xdp-recreation.
