MODEL #: 74510G “FREEDOM N Swing 4 Leg Seesaw Galvanized” Assembled dimensions are 168"*93"*73". Allow 6 - 12 ft of clearance around the perimeter of the swing set area when fully assembled. OWNER'S MANUAL, ASSEMBLY INSTRUCTIONS, CARE, MAINTENANCE AND USER'S GUIDE Important Instructions & Warnings! Please read this entire instruction and assembly manual completely before proceeding. You must follow all safety instructions while using this equipment.
IMPORTANT INSTRUCTIONS AND WARNINGS WARNING READ ALL INSTRUCTIONS BEFORE ASSEMBLING OR USING THIS EQUIPMENT AGE & WEIGHT LIMIT This product is designed to be used by up to seven (7) children between the ages of 3 to 8. Maximum user weight is 100 pounds (45 kg) each with a combined maximum weight of 700 pounds (318 kgs). The play set is designed for children over three (3) years of age up to (8) years of age. Use by smaller children can result in entrapment.
DO NOT install your play set over hard surface, e.g. asphalt, concrete, packed earth, tile or brick floor. A fall onto a hard surface can result in serious injury or death to the user.
PLAY SUPERVISION DO NOT allow more than one child to play on the individual swing, stand R swing or slide component at any one time. DO NOT allow children to stand on the slide, swing seats, flying saucer, or glide ride. The glide ride is made for only two users at a time. The saucer is made for one or two users at a time. DO NOT allow children to walk too close to moving parts.
INSPECTION PRIOR TO EACH USE OR DAILY INSPECTION DO NOT use the equipment if any bolts or nuts are missing or loose. ALWAYS check to ensure the equipment and all parts are well secured and stable before each use. ALWAYS clear the play area of any rocks, sharp objects, or any materials that could be potentially hazardous to users.
ANCHORING (NOTE:ANCHORS ARE NOT INCLUDED-MUST BE PURCHASED SEPARATELY) There are different ways of anchoring the equipment, depending on the type of ground on which the equipment is to be installed. Make sure that all anchors are below ground level to prevent tripping. You should consult your local contractor to decide the most appropriate way to anchor the equipment in your location.
FRAME LEG CONCRETE 12-5/8” 5” 2” BRICK OR GRAVEL BED Note: The maximum fall height for this product is 4 feet. The minimum ground clearance between the bottom of the suspended plays and the playing or ground surface must be 8 inches. You must maintain a minimum of 8 inches of ground clearance. 8” WARNING Please properly anchor the swing set to minimize the risk of injury or death. If the swing set is used without proper anchoring, it may be dangerous and may tilt over.
CARE AND MAINTENANCE CHECKLIST AT THE BEGINNING OF EACH PLAY SEASON: Tighten all hardware. Lubricate all metallic moving parts. Check all protective coverings on bolts, pipes, edges, and corners. Replace if they are loose, cracked, or missing. Check all moving parts including swing seats and chains for wear, rust or other deterioration. Replace as needed. Check metal parts for rust. If found, sand and repaint using a non-lead paint meeting the requirements of 16 CFR 1303.
TOOLS NEEDED Please prepare the following tools prior to assembling this equipment. Special Socket Wrench (Not included) Hammer (If you intend to install anchor, this is needed) Wrench (Not Included) Flat Head and Philips Head Screwdriver (Not included) Small Allen Wrench （Not Included) Tape Measure (Not included) Wrench (Included) Medium Allen Wrench (Included) Big Allen Wrench (Included) Scissors (Not included) DO NOT RETURN TO RETAILER YOU PURCHASED AT. CONTACT XDP FOR PARTS AND SUPPORT AT 1.
Part list for main frame assembly A1 LEFT TOP BAR 1 A2 MIDDLE TOP BAR 1 A3 RIGHT TOP BAR 1 A7 TOP SECTION LEG 4 A8 BOTTOM SECTION LEG WITH FOAM 3 A9 BOTTOM SECTION LEG WITH FOAM 1 A10 CROSS BAR (WITH TWO HOLES) 1 A11 CROSS BAR (WITH FOUR HOLES) 1 Hardware used for main frame assembly B1 BOLT 5/16"(63mm) 12 B2 BOLT 5/16"(68mm) 4 B3 NYLON NUT 5/16" 16 B4 PLASTIC CAP (WITH ARC WASHER) 16 B5 ARC WASHER 5/16" 12 B6 WASHER 5/16" 4 DO NOT RETURN TO RETAILER YOU PURCHASED A
Part list for swing seat assembly J1 J3 J3-N PVC COVERED CHAIN EYE BOLT WITH ATTACHMENT BOLT (PRE-ASSEMBLED ON J1) ONE EYE BOLT WITH ATTACHMENT BOLT (PRE-ASSEMBLED ON J1) K1 SWING SEAT 2 2 2 1 Hardware used for swing seat assembly J6 NUT 5/16" 4 J7 WASHER 5/16" 2 J8 PLASTIC CAP (WITH ARC WASHER) 2 J9 PLASTIC CAP (WITH FLAT WASHER) 2 Part list for Stand R Swing assembly J1A J3A J3A-N K2 PVC COVERED CHAIN (PRE-ASSEMBLED) EYE BOLT WITH ATTACHMENT BOLT (PRE-ASSEMBLED ON J1A) EYE BOLT WIT
Part list for SUPER DISC (TM) Swing assembly R1-N PVC COVERED CHAIN EYE BOLT WITH ATTACHMENT BOLT (PRE-ASSEMBLED ON R1-N) EYE BOLT WITH ATTACHMENT BOLT (PRE-ASSEMBLED ON R1-N) R2A-N R2B-N 4 2 4 R3-N DISC SWING TUBE 4 R3-1 DISC SWING TUBE FOAM (PRE-ASSEMBLED ON R3-N) 4 R4-N DISC SWING FABRIC 1 Hardware used for SUPER DISC (TM) Swing assembly F1-N NUT 5/16" 6 F2-N ARC WASHER 4 F3-N PLASTIC CAP (WITH ARC WASHER) 2 Part list for slide assembly X1-N SLIDE SUPPORT (WITH OPENING) 1 X2-N
Hardware used for slide assembly Y1 PLASTIC CONNECTOR 2 Z1 BOLT 1/4"(38mm) 6 Z2 BOLT 1/4"(115mm) 2 Z3 SPRING WASHER 4 Z4 CAP NUT 1/4" 10 Z5 CAP BOLT 1/4"x1/2" 4 Z6 SPRING WASHER (small) 20 Z7 BOLT 1/4"(75mm) 2 Z8 BOLT 1/4"(58mm) 4 Part list for seesaw assembly U16 SEAT 2 U17 SEAT SUPPORT 1 U18 HANDLE BAR 2 U19-1 LEFT HANDLE BAR SUPPORT 2 U19-2 RIGHT HANDLE BAR SUPPORT 2 U20 L SHAPED TUBE 1 DO NOT RETURN TO RETAILER YOU PURCHASED AT.
Hardware used for seesaw assembly U1 BOLT 5/16”(82MM) 4 U2 BOLT 5/16”(63MM) 1 U3 BOLT 5/16”(68MM) 2 U4 ARC WASHER Φ8.5*T1.5MM 10 U5 NUT 5/16” 7 U6 CAP NUT 1/4” 4 U7 BOLT 1/4”(37MM) 4 U8 SPRING WASHER 4 U9 SCREW M4(12MM) 4 U10 PLASTIC CAP (WITH FLAT WASHER) 1 U14 FLAT WASHER 1 U15 PLASTIC CAP (WITH ARC WASHER) 2 U21 SPRING WASHER(SMALL) 4 DO NOT RETURN TO RETAILER YOU PURCHASED AT. CONTACT XDP FOR PARTS AND SUPPORT AT 1.866.884.0535 or service@xdp-recreation.
ASSEMBLY INSTRUCTIONS Place the playground equipment on level ground and not less than 6ft (1.8m) from any structure or obstruction such as a fence, garage, house, overhanging branches, laundry line, or electrical wires. Do not install the playground equipment over concrete, asphalt, packed earth, or any other hard surface; a fall onto a hard surface can result in serious injury or death to the equipment user. Adequate overhead clearance is essential.
STEP 1 – Assemble the top bar frame of the swing set Connect A1, A2 and A3 secure with B1, B5, B4 and B3 as shown below. Note: All round holes should be facing up and concave holes facing down. B3 B3 B4 B4 B5 A2 B5 A3 A1 B1 B1 DO NOT RETURN TO RETAILER YOU PURCHASED AT. CONTACT XDP FOR PARTS AND SUPPORT AT 1.866.884.0535 or service@xdp-recreation.
STEP 2 – Assemble the support legs of swing set Connect A1 to A7 and secure using B1, B5, B4 and B3 as shown below. Repeat the above step for the right side of the swing set (A2 and A3,A7). A1 B4 B1 B1 B5 A7 B5 B3 A7 A8 A9 DO NOT RETURN TO RETAILER YOU PURCHASED AT. CONTACT XDP FOR PARTS AND SUPPORT AT 1.866.884.0535 or service@xdp-recreation.
STEP 3 – Assemble the support legs of swing set Connect A7 to A8, A9 and secure using B1, B5, B4 and B3 as shown below. Repeat the above step for the right side of the swing set (A2 and A3). A7 A7 B5 B3 B4 B1 B3 B4 A8 B5 B1 A9 DO NOT RETURN TO RETAILER YOU PURCHASED AT. CONTACT XDP FOR PARTS AND SUPPORT AT 1.866.884.0535 or service@xdp-recreation.
STEP 4 – Attach the crossbar to the support legs. Attach A10 to the outer side of A8 & A9 and secure using B2, B6, B4 and B3. A1 A7 A7 B3 B6 B4 B2 B3 A8 A10 B4 B6 B2 A9 DO NOT RETURN TO RETAILER YOU PURCHASED AT. CONTACT XDP FOR PARTS AND SUPPORT AT 1.866.884.0535 or service@xdp-recreation.
Attach A11 to the outer side of A8 and secure using B2, B6, B4 and B3. B3 B4 B6 B3 B2 A11 B4 B6 B2 A8 A8 A1 A2 A3 A7 A7 A10 A8 A11 A8 A9 DO NOT RETURN TO RETAILER YOU PURCHASED AT. CONTACT XDP FOR PARTS AND SUPPORT AT 1.866.884.0535 or service@xdp-recreation.
STEP 5 - "SWING SEAT" Assembly ( w. "Adjustable Height" Feature) Connect swing set chains to the top bar by inserting J3-N through A3, securing with J8 and J6 as shown in Diagram A. Connect swing seat to the chains by inserting J3 through K1 and secure with J7, J9 and J6 as shown in Diagram B. J6 DIAGRAM A J6 J8 A3 J3-N J3-N J1 J1 J3 J3 J3-N 1 4 3 2 5 DO NOT RETURN TO RETAILER YOU PURCHASED AT. CONTACT XDP FOR PARTS AND SUPPORT AT 1.866.884.0535 or service@xdp-recreation.
DIAGRAM B J1 J3 J1 J3 K1 J7 J7 J9 J9 J6 J6 Important that the ‘washer’ ( J7 ) is included in the seat assembly. DO NOT RETURN TO RETAILER YOU PURCHASED AT. CONTACT XDP FOR PARTS AND SUPPORT AT 1.866.884.0535 or service@xdp-recreation.
STEP 6 -"Stand R Swing" Seat Assembly ( w. "Adjustable Height" Feature ) Connect Stand R Swing chains to the top bar by inserting J3A-N through A2 & A3 and securing with J8A and J6A as shown in Diagram A. Connect Stand R Swing to the chains by inserting J3A through K2 and secure with J7A, J9A and J6A as shown in Diagram B. DIAGRAM A J6A J6A J8A A3 J8A A2 J3A-N J3A-N J1A J1A J3A J3A J3A-N 1 4 3 2 5 DO NOT RETURN TO RETAILER YOU PURCHASED AT. CONTACT XDP FOR PARTS AND SUPPORT AT 1.866.884.
DIAGRAM B J1A J3A J1A J3A K2 J7A J7A J9A J9A J6A J6A Important that the ‘washer’ ( J7A ) is included in the seat assembly. DO NOT RETURN TO RETAILER YOU PURCHASED AT. CONTACT XDP FOR PARTS AND SUPPORT AT 1.866.884.0535 or service@xdp-recreation.
STEP7–Super Disc (TM) Swing Assembly Separation of foam tube R3-1 from R3-N Insert the foam tube R3-1 into R4-N first, then insert R3-N into R3-1 in R4-N. Slide the smaller ends of R3-N tubes into the pockets of Disc Swing Fabric (R4-N). Connect the four tubes together. Align the holes with the round holes face down. R3-1 R3-N R3-1 R3-N R3-1 R4-N R3-N R4-N DO NOT RETURN TO RETAILER YOU PURCHASED AT. CONTACT XDP FOR PARTS AND SUPPORT AT 1.866.884.0535 or service@xdp-recreation.
STEP 8–Attach Super Disc (TM) Swing to the Swing Set Frame Connect the chain (R1-N) to the disc swing by inserting R2B-N and securing with F2-N and F1-N as shown in Diagram A. Connect disc swing to the top bar by inserting R2A-N through A1 and A2, securing with F3-N and F1-N as shown in Diagram B.
STEP 9 - Slide assembly Insert X5-N into the base of Y2. Secure using Z8, Z6 and Z4. Attach X4-N to Y2. Note: Make sure that the bolt holes face up. Y2 X4-N Z8 Z6 Bolt hole faces up. Z4 Z6 X5-N Z8 NOTE: 1. Do not over-tighten the nuts and bolts at every step. 2. Do not snap in the cover of plastic cap until you have finished the assembly of each step and went back to tighten all of the nuts and bolts. DO NOT RETURN TO RETAILER YOU PURCHASED AT. CONTACT XDP FOR PARTS AND SUPPORT AT 1.866.884.
STEP 10 - Slide assembly (continued) Attach X6 to X1-N and X2-N. The inner sides of both X2-N and X1-N, where X6 (slide ladder steps) is attached to, are with concave holes. Secure each side using Z1, Z6 and Z4. Attach X3-N to X1-N and X2-N. Align holes and hold in position. Narrow side (Direction as shown below) Front side X2-N Wide side faces the front direction of the slide X1-N Z1 Z6 Z4Z6 X3-N X6 Z4 Z1 Z6 Z6 X3-N NOTE: 1. Do not over-tighten the nuts and bolts at every step. 2.
STEP 11- Slide assembly (continued) Secure the two sides of the slide using Z2, Z6 and Z4, in the sequence shown in the diagram. Attach X4-N to X1-N and X2-N; Secure using Z1, Z6, Z3 and Z5 as shown in the enlarged diagram. X4-N X2-N X1-N Z1 Z6 Z2 Z6 Z3 Z4 Z5 Z6 Y2 Z2 Z6 X1-N X3-N NOTE: 1. Do not over-tighten the nuts and bolts at every step. 2. Do not snap in the cover of plastic cap until you have finished the assembly of each step and went back to tighten all of the nuts and bolts.
STEP 12 - Slide assembly (continued) Fit Y1 in between X1-N and A11; Secure using Y1, Z7, Z6 and Z3, Z5 Z5 X1-N Z3 Y1 Z3 Z7 Z5 Z6 A11 A8 A8 NOTE: 1. Do not over-tighten the nuts and bolts at every step. 2. Do not snap in the cover of plastic cap until you have finished the assembly of each step and went back to tighten all of the nuts and bolts. DO NOT RETURN TO RETAILER YOU PURCHASED AT. CONTACT XDP FOR PARTS AND SUPPORT AT 1.866.884.0535 or service@xdp-recreation.
STEP 13 - See-Saw assembly Attach U20 to A9. Align the holes on U20 to the two holes on the bottom of A9 and secure using U3, U4, U15 and U5 as shown below. U5 U15 U5 U15 A9 U4 U3 U20 DO NOT RETURN TO RETAILER YOU PURCHASED AT. CONTACT XDP FOR PARTS AND SUPPORT AT 1.866.884.0535 or service@xdp-recreation.
STEP 14 - See-Saw assembly (continued) Secure U17 to U20 by using U2, U14, U10 and U5 as shown below. U2 U14 A9 U17 U10 U5 U20 DO NOT RETURN TO RETAILER YOU PURCHASED AT. CONTACT XDP FOR PARTS AND SUPPORT AT 1.866.884.0535 or service@xdp-recreation.
STEP 15 - See-Saw assembly (continued) Attach U18 to U19-1 and U19-2 and secure using U9 and U21. Repeat for other U18, U19-1 and U19-2. U18 U9 U21 U19-1 U21 U9 U19-2 DO NOT RETURN TO RETAILER YOU PURCHASED AT. CONTACT XDP FOR PARTS AND SUPPORT AT 1.866.884.0535 or service@xdp-recreation.
STEP 16 - See-Saw assembly (continued) Secure U19-1 & U19-2 to U17 using U1, U4 and U5 as shown below. Repeat for the other side. U18 U20 U19-2 U17 U5 U4 U19-1 U4 U4 U1 U4 U1 DO NOT RETURN TO RETAILER YOU PURCHASED AT. CONTACT XDP FOR PARTS AND SUPPORT AT 1.866.884.0535 or service@xdp-recreation.
STEP 17 - See-Saw assembly (continued) Secure U16 to U19-1 and U19-2 using U7, U8 and U6 as shown below. Repeat for the other side. U7 U16 U8 U6 DO NOT RETURN TO RETAILER YOU PURCHASED AT. CONTACT XDP FOR PARTS AND SUPPORT AT 1.866.884.0535 or service@xdp-recreation.
Congratulations! You have now completed the swing set assembly. Please make sure to thoroughly check all parts and hardware to make sure all bolts and nuts are well secured before using the playground equipment. WARNING - Do not let children use the playground equipment until it is properly assembled and anchored. DO NOT RETURN TO RETAILER YOU PURCHASED AT. CONTACT XDP FOR PARTS AND SUPPORT AT 1.866.884.0535 or service@xdp-recreation.
Dear Customer: Thank you for your purchase of an XDP Recreation swing set. By following the instruction manual, reading all safety and assembly instructions, and properly anchoring your swing set in the ground, your kids will safely enjoy hours of fun. Detailed below is our warranty covering your purchase. Please be sure to read it and contact us in the event you need service or parts. DO NOT RETURN THE SET TO THE STORE YOU PURCHASED IT.
ADDENDUM - PRODUCT INFORMATION & SUPPORT Please Retain Sales Receipt for Warranty Purposes. DO NOT RETURN THE SET TO THE STORE. If replacement parts or IF Customer Service is needed please contact XDP Recreation by email at service@xdp-recreation.com or CALL 1-866-884-0535 between 8:00am and 5:00pm (Eastern Standard Time), Monday - Friday. This Swing Set is designed to be used safely by children, ages 3 years to 8 years, with weight capacity of 100 lbs per child.
2019 Dear Customer, THANK YOU for being an XDP Recreation Customer. IT’S HERE – The NEW FIREFLY LED SWING Check out our Website or the General Marketplace For this FANTASTICALLY / FUN STROBING – LED – COLORED – FLASHING MODES SWING www.xdp-recreation.com KEEP HAVING FUN! www.xdp-recreation.com Alpharetta, Ga. 30005 USA DO NOT RETURN TO RETAILER YOU PURCHASED AT. CONTACT XDP FOR PARTS AND SUPPORT AT 1.866.884.0535 or service@xdp-recreation.
