Document NO.
Document NO.: WI-FHF-CS-PMIIICSL-A Page 2of 9 MODEL: CS-PMIIICSL REV: A/1 1. PREFACE/ ........................................................................................................................ 2 2. TECHNICAL/FEATURES 3. TEST/ 4. PROTECTION CAPABILITY TEST METHODAND REQUEST/ 5. CELL/ 6. OUTLINE/ 7. PCM ELECTRONIC CHARACTERISTIC/ 8. PACKING/ .......................................................................................... 4 .........................................
Document NO.: WI-FHF-CS-PMIIICSL-A Page 3of 9 MODEL: CS-PMIIICSL REV: A/1 2.Technical Features Item Rated performance 2.1 Rated Voltage Note 3.7V 2.2 Discharge Cut-off Voltage 3V 2.3 Rated Capacity 1600mAh 2.4 Limited Charge Voltage 0.2C Discharge 0.2C 4.2VDC CC-CV (Constant Current With Constant Voltage) 2.5 Charge Method (CC-CV) 2.6 Standard Charge Current 2.7 Quick Charge Current 2.8 Max Discharge Current 2.
Notes( Document NO.: WI-FHF-CS-PMIIICSL-A Page 4of 9 MODEL: CS-PMIIICSL REV: A/1 ): 1. Period of storage is counted from shipping date 2. Test Method and standard listed as below, environment temperature (15 25) , CC/CV mode, 0.2C constant current charge to 4.2V, then constant voltage charge mode, cut off current 0.01C 0.2C constant current discharge, cut off voltage 3.0V more than 5 hours discharging time. , 3.Test ( 0.01C (15 25) ,CC/CV 0.2C , ,0.2C 3.0V 4.2V, 5 ) 3.
Document NO.: WI-FHF-CS-PMIIICSL-A Page 5of 9 MODEL: CS-PMIIICSL REV: A/1 3.3 Test method and request ( Item Appearance 1 2 Insulation Resistance Nominal Capacity Request By sight 30CM vertically Case appearance should be smooth w/o nick, burr and other mechanical damage. Exposed metallic part should not be Oxidized. Case should not be distorted. , Test the external packing of battery and insulation between poles using insulation-meter Environment temperature (15 25) , CC/CV mode, 0.
Document NO.: WI-FHF-CS-PMIIICSL-A Page 6of 9 MODEL: CS-PMIIICSL REV: A/1 discharging less than 42 minutes, cycle life should be ending. 1C 42 8 Vibration Proof Capability After standard charged, keep for 0.5h~ 1h,then installed onto the vibration test with clamps. Equipment parameters of frequency and amplitude are as follows(the frequency is to be varied at the rate of 1oct/min between 10Hz 55Hz, and repeat vibration for 30min.
Document NO.: WI-FHF-CS-PMIIICSL-A Page 7of 9 MODEL: CS-PMIIICSL REV: A/1 3.4. Shipping Voltage (Inspection before shipment): ≥3.7V ( ): ≥3.7V 4.Protection Capability Test Method and Request Item 1 Test Method Overcharge Test Request Apply a 5V voltage and a 1C charge current on the battery for 10 hours. 10hs 5V Battery could not be burst, burn, leak and smoke 1C 2 Over discharge Test Discharge the battery at 1C to cut off voltage then discharge with loading 30Ω for 24hs.
6. OUTLINE ( Document NO.: WI-FHF-CS-PMIIICSL-A Page 8of 9 MODEL: CS-PMIIICSL REV: A/1 ): L=52.1mm MAX W=34mm MAX H=10.5mm MAX P+ P- P+ P- 7 PCM Electronic Characteristic / Over-charging Over-discharging Over-current Short-circuit Quiescent voltage voltage protection protection protection time current ≤300us ≤8uA protection 4.3V±25mV figure 2.45V±60mV 4.5 A±0.
Document NO.: WI-FHF-CS-PMIIICSL-A Page 9of 9 MODEL: CS-PMIIICSL REV: A/1 8. Packing / Packing method, as the customer required.
