HDMI4X4 USER MANUAL www.xantech.
CONTENTS 1 Introduction / Product Features / Package Contents 2 Panel Layouts 3 Operational Instructions 4 IR Remote Control Installation 5 EDID Configuration Guide 6 EDID Modes 7 Resolving IR conflicts 8 RS-232 Control Interface 9 Rack Mount Diagram 10 Specifications
INTRODUCTION The 4X4 HDMI™ Matrix routes high definition video in multiple resolutions up to 1080p plus multichannel digital audio from any of the four HDMI™ sources to the displays. Four outputs gives you the choice of sending high definition audio and video signals up to four displays. Any four sources to any four dislay devices matrix switching allows for maximum versatility for integrated systems.
FRONT PANEL LAYOUT -2-
OPERATION NOTES PLEASE READ THESE NOTES BEFORE INSTALLING OR OPERATING THE HDMI4X4 MATRIX SWITCHER • • • • The 4X4 HDMI Matrix is housed in a metal box for better RF shielding. The 4X4 HDMI Matrix works with all DVI and HDMI displays. The 4X4 HDMI Matrix supports both AUDIO and VIDEO signals. The 4X4 HDMI Matrix is fully HDCP compliant. VIDEO COMPATIBILITY NOTE An HDMI source connects to the HDMI4X4 Matrix Switcher with four input cables and four output cables.
RMT16-IR INSTALLATION 1. Remove battery cover from the back of the RMT16-IR remote. 2. Verify that DIP switches 1 & 2 are in the down (OFF) position. 3. Insert the battery; hold the battery so that you can see the positive side facing up. The side that is not marked must be facing down. 4. Test the RMT16-IR remote by pressing ONLY one button at a time. The indicator light on the remote will flash once each time you press a button.
CUSTOM EDID CONFIGURATION VIA DIP SWITCHES Extended display identification data (EDID) is a data structure provided by a display to describe its capabilities to any source that asks for it. The EDID includes manufacturer name, product type, timings supported by the display, display size, luminance data, (for digital displays only) pixel mapping data, supported audio channels and formats.
SETTING EDID MODES USING THE DIP SWITCH BANK: EDID Mode 0 (Switch 1=OFF Switch2=OFF Switch5=ON) -EDID is copied from the device connected to the first active HDMI output port. - All features newer than HDMI 1.2 are cleared. EDID Mode 1 (Switch 1=ON Switch2=OFF Switch5=ON) -Same as Mode 0 and adds basic audio support. EDID Mode 2 (Switch 1=OFF Switch2=ON Switch5=ON) -Same as Mode 0 and adds full audio support.
Resolving Infrared Code Conflicts In the event of IR conflicts, please do the following: 1. Remove the battery cover from the back of the RMT16-IR remote. 2. Locate the DIP Switches above the batteries. 3. Switch the DIP Switches on the RMT16-IR to any of the combinations pictured below. 4. DIP Switches 1 and 2 in the RMT16-IR infrared remote correspond with DIP Switches 3 and 4 inside the 4X4 HDMI Matrix respectively.
RS-232 INTERFACE ASCII 1 2 3 4 5 6 7 8 9 a b c d e f g 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 Binary 0011 0001 0011 0010 0011 0011 0011 0100 0011 0101 0011 0110 0011 0111 0011 1000 0011 1001 0110 0001 0110 0010 0110 0011 0110 0100 0110 0101 0110 0110 0110 0111 RS232 Settings Bits per second Data bits Parity Stop bits Flow Control 19200 8 None 1 None -8-
4X4 HDMI RACK MOUNT DIAGRAM -9-
SPECIFICATIONS Video Amplifier Bandwidth Input Video Signal Input DDC Signal Single Link Range HDMI Input/Output Connector Remote Control Port Power Consumption Power Supply Dimensions Shipping Weight 1.65 Gbps 1.2 volts p-p 5 volts p-p (TTL) 1080p / 1920 x 1200 Type A 19-pin Female RS-232 Female, Mini-Stereo 60 watts (max) 24V DC 17” W x 1.75” H x 5.875” D 10 lbs. Technical Support Mailing Address Hours: 7AM-5:30 PM PST Phone: 800.843.5465 press 2 for Tech Support FAX: 800.492.
www.xantech.
