User's Manual

Caution: When removing bottom cover for the purposes of cable or SAM card installation, remember to reinstallation the protective cover and make sure to keep it in place.
Caution: To reduce the risk of fire, use only No. 26 AWG or larger UL Listed or CSA Certified Telecommunication Line Cord.
Caution: Risk of explosion if the battery is replaced by an incorrect type. Please dispose of used battery according to the instructions.
Warning: This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.
Warning: If the device, T103, is used without the detachable privacy shield, the following criteria needs to be met by the Installed Environment of the PED for complying with the PCI privacy screen design requirement:
A. Positioning of the PED on the check-stand in such way as to make visual observation of the PIN-entry process infeasible.
 Visual shields designed into the check-stand.
 Position the PED so that it is angled in such a way to make PIN spying difficult.
B. Pop-up (temporary) privacy shield attached to the PED mounting stand. Consumer (through education & prompting) or merchant would put the shield in place during PIN entry.
C. Installing PED on an adjustable stand that allows consumers to swivel the terminal sideways and/or tilt it forwards/backwards to a position that makes visual observation of the PIN-entry process difficult.
D. Positioning of in-store security cameras such that the PIN-entry keypad is not visible.
E. Instructing the cardholder regarding safe PIN-entry, done with a combination of:
 Signage on the PED.
 Prompts on the display, possibly with a "click-through" screen.
 Potentially literature at the point of sale.
 A logo for safe PIN-entry process.
Table A1: Matrix of Observation Corridors and PIN Protection Method
Observation Corridors
Method Cashier Customers
in Queue
Customers
Elsewhere
On-Site
Cameras
Remote
Cameras
PED Stand A M H L L L
PED Stand B H H H L M
Check-Stand A L M M L H
Check-Stand B H H M H H
Customer Instructio
n
H* H* H* H* H*
z Customer Instruction methods are less repeatable and therefo re should be used in combination with other methods. L = low , M = medium, H = high.
Industry Canada Statement is provided for xA PT-103W iFi and xAPT-103, xCE_T103WiFi and xCE_T103 model.
NO TICE: This equipment meets the applicable Industry Canada Terminal Equipment Technical Specifications. This is confirmed by the registration number. The abbreviation, IC, before the registration number signifies that registration was
performed based on a Declaration of Confo rmity indicating that Industry Canada technical specificatio ns were met. It does not imply that Industry Canada approved the equipment.
NO TICE: The Ringer Equivalence Number (REN) for this terminal equipment is 0.1. The REN assigned to each terminal equipment provides an indication of the maximum number of terminals allow ed to be connected to a telephone interface.
The termination on an interface may consist of any combination of devices subject only to the requirement that the sum of the Ringer Equivalence Numbers of all the devices do es not exceed five.
AVIS : Le présent matériel est conforme aux spécifications techniques d’Industrie Canadaapplicables au matériel terminal. Cette conformité est co nfirmée par le numérod'enregistrement. Le sigle IC, p lacé devant le numéro d'enregistrement,
signifie quel’enregistrement s’est effectué conformément à une déclaratio n de co nfo rmité et indique queles sp écifications techniques d'Industrie Canada ont été respectées. Il n’implique pasqu’Industrie Canada a approuvé le matériel.
AVIS : L'indice d'équivalence de la sonnerie (IES) du présent matériel est de 0.1. L'IESassigné à chaque dispo sitif terminal indique le nombre maximal de terminaux qui peuvent êtreraccordés à une interface téléphonique. La terminaison d'une
interface peut consister en unecombinaiso n quelco nque de dispo sitifs, à la seule condition que la somme d'indicesd'équivalence de la sonnerie de tous les dispositifs n'excède pas 5.
Industry Canada Statement
This device co mplies w ith RSS-210/ 247 of the Ind ustry Canada Rules. Operation is subject to the following two conditions:
(1) this device may not cause interference and
(2) this device must accept any interference, including interference that may cause undesired operation of the device
Ce dispo sitif est conforme à la norme CNR-210/ 247 d'Industrie Canada applicable aux appareils radio exempts de licence. Son fonctionnement est sujet aux deux conditions suivantes:
(1) le dispo sitif ne do it pas produire de brouillage préjudiciable, et
(2) ce dispositif doit accepter to ut brouillage reçu, y compris un brouillage susceptible de provoquer un fonctionnement indésirable.
FO R DEV ICE USAGE
Radiation Exposure Statement:
The product comply with the Canada RF exposure limit set forth for an uncontrolled environment and are safe for intended operation as described in this manual. The further RF expo sure reduction can be achieved if the product can be kept as
far as possible fro m the user body or set the device to low er output pow er if such function is available.
This transmitter must not be co-located or op erating in conjunction with any other antenna or transmitter.
Déclaration d'exposition aux radiations:
Le produit est conforme aux limites d'exposition po ur les ap pareils RF pour les Etats-Unis et le Canada établies pour un environnement non contrôlé.
Le produit est sûr pour un fonctionnement tel que décrit dans ce manuel. La réduction aux expositions RF peut être augmentée si l'appareil peut être conservé aussi lo in que po ssible du corps de l'utilisateur ou que le dispositif est réglé sur la
puissance de sortie la plus faible si une telle fonction est disponible.
Cet émetteur ne doit p as être co-situé ou fonctionner en conjonction avec une autre antenne ou émetteur.
Federal Communication Commission Interference Statement is for xA PT-103WiFi and xCE_T103WiFi model.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that
may cause undesired op eration.
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to pro-vide reasonable protection against harmful interference when the equipment
is operate din a commercial environment. This equipment generates, uses, and can radiate radiofrequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for comp liance could void the user's autho rity to operate this equipment.
Caution: Use only shielded signal cables to connect I/ O devices to this equipment. You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the
equipment.
IMPO RTANT NOTE:
FO R DEV ICE USAGE
Radiation Exposure Statement:
The product comply with the FCC RF exposure limit set forth for an uncontrolled environment and are safe for intended operation as described in this manual. The further RF exposure reduction can be achieved if the product can be kept as
far as possible fro m the user body or set the device to low er output pow er if such function is available.
This transmitter must not be co-located or op erating in conjunction with any other antenna or transmitter.
FCC REQUIREM EN TS for xAPT-103WiFi and xCE_T103WiFi model.
This equipment complies with Part 68 of FCC Rules. On the base unit of this equipment is a label that co ntains, among other information, the FCC Registration Number and Ringer Equivalence Number (REN) for this equipment. IF
REQUESTED, THIS INFORMATION MUST BE GIVEN TO THE TELEPHONE COMPANY.
This equipment complies with Part 68 of the FCC rules and the requirements adopted by the ACTA. On the botto m of this equipment is a label that contains, among other info rmation, a p roduct identifier in the format US:
N7KMM01BT103WIFI. If requested, this number must be provided to the telephone company. The REN is used to determine the number of devices that may be co nnected to a telephone line. Excessive RENs on a telephone line may result in
the devices not ringing in response to an incoming call. In most but not all areas, the sum of RENs should not exceed five (5.0). To be certain of the number of devices that may be connected to a line, as determined by the total RENs, contact the
local telepho ne company. Fo r products approved after July 23, 2001, the REN for this product is part of the p roduct identifier that has the format N7KMM01BT103W IFI. The digits represented by 01B are the REN without a decimal point (e.g.,
03 is a REN of 0.3). For earlier products, the REN is separately shown on the label. If your equipment causes harm to the telepho ne network, the telephone company may discontinue your service tempo rarily. If possible, they will notify yo u in
advance. But if advance notice is not p ractical, yo u w ill be notified as soo n as possible. You will be informed of your right to file a co mplaint w ith the FCC. Your telephone company may make changes in its facilities, equipment, operatio ns or
procedures that could affect the proper functio ning of yo ur equipment. If they do, you will be notified in advance to give you an oppo rtunity to maintain uninterrupted telephone service. If yo u experience trouble with this telephone
equipment, please contact the following address and phone number for information on obtaining service or repairs. The telephone company may ask that you disconnect this equipment from the netw ork until the problem has been corrected
or until you are sure that the equipment is not malfunctioning. This equipment may not be used on coin service provided by the telephone company. Connection to party lines is subject to state tariffs.
COM PA NY: Zakus, INC.
ADDRESS: 146 Main Street, suite 208 Los Altos, CA 94022 U.S.A .
TEL NO: 650-917-9158
A plug and jack used to connect this equipment to the p remises wiring and telephone netwo rk must comply with the applicable FCC Part 68 rules and requirements adopted by the A CTA. A compliant telephone cord and modular plug is
prov ided with this product. It is designed to be connected to a compatible modular jack that is also compliant. See installation instructions for details.
The above information is the exclusive intellectual property of XAC Automation Corporation and shall not be disclosed,
distributed or reproduced without permission of XAC Automation Corporation.
XAC AUTOMATION CORP. shall not be held liable for technical and editorial omissions or errors made herein; nor for
iidtl tild lti f thf ihi f
fhi t i l
XAC Automation Corporation
886-3-577-2738