User's Manual

ManualsBrandsXAC Automation ManualsElectronicsTerminal

Radiation Exposure Statement:

This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with

minimum distance 20cm between the radiator & your body.

Declaration d'exposition aux radiations:

Cet equipement est conforme aux limites d'exposition aux rayonnements IC etablies pour un environnement non controle. Cet equipement doit etre installe et

utilise avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps.

Federal Communication Commission Interference Statement

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to

pro-vide reasonable protection against harmful interference when the equipment is operate din a commercial environment. This equipment generates, uses, and

can radiate radiofrequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio

communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the

interference at his own expense.

FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this

equipment.

IMPORTANT NOTE:

FCC Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with

minimum distance 20cm between the radiator & your body.

FCC REQUIREMENTS

This equipment complies with Part 68 of FCC Rules. On the base unit of this equipment is a label that contains, among other information, the FCC Registration

Number and Ringer Equivalence Number (REN) for this equipment. IF REQUESTED, THIS INFORMATION MUST BE GIVEN TO THE TELEPHONE

COMPANY.

This equipment complies with Part 68 of the FCC rules and the requirements adopted by the ACTA. On the bottom of this equipment is a label that contains,

among other information, a product identifier in the format US: N7KMM01BFD130. If requested, this number must be provided to the telephone company. The

REN is used to determine the number of devices that may be connected to a telephone line. Excessive RENs on a telephone line may result in the devices not

ringing in response to an incoming call. In most but not all areas, the sum of RENs should not exceed five (5.0). To be certain of the number of devices that may be

connected to a line, as determined by the total RENs, contact the local telephone company. For products approved after July 23, 2001, the REN for this product is

part of the product identifier that has the format N7KMM01BFD130. The digits represented by 01B are the REN without a decimal point (e.g., 03 is a REN of 0.3).

For earlier products, the REN is separately shown on the label. If your equipment causes harm to the telephone network, the telephone company may discontinue

your service temporarily. If possible, they will notify you in advance. But if advance notice is not practical, you will be notified as soon as possible. You will be

informed of your right to file a complaint with the FCC. Your telephone company may make changes in its facilities, equipment, operations or procedures that

could affect the proper functioning of your equipment. If they do, you will be notified in advance to give you an opportunity to maintain uninterrupted telephone

service. If you experience trouble with this telephone equipment, please contact the following address and phone number for information on obtaining service or

repairs. The telephone company may ask that you disconnect this equipment from the network until the problem has been corrected or until you are sure that the

equipment is not malfunctioning. This equipment may not be used on coin service provided by the telephone company. Connection to party lines is subject to state

tariffs.

COMPANY: Zakus, INC.

ADDRESS: 146 Main Street, suite 208 Los Altos, CA 94022 U.S.A.

TEL NO: 650-917-9158

A plug and jack used to connect this equipment to the premises wiring and telephone network must comply with the applicable FCC Part 68 rules and

requirements adopted by the ACTA. A compliant telephone cord and modular plug is provided with this product. It is designed to be connected to a compatible

modular jack that is also compliant. See installation instructions for details.

The above information is the exclusive intellectual property of XAC Automation Corporation and shall not be disclosed,

distributed or reproduced without permission of XAC Automation Corporation.

XAC AUTOMATION CORP. shall not be held liable for technical and editorial omissions or errors made herein; nor for

incidental or consequential damages resulting from the furnishing, performance or use of his material.

XAC Automation Corporation

886-3-577-2738