Winterm™ Model 9450XE, 9455XL and J400, Product 941GXL 512MB Flash Option Kit Installation Guide
Winterm™ Model 9450XE, 9455XL and J400, Product 941GXL Flash Option Kit Installation Guide Issue: 072205 Wyse Technology Inc.
Copyright Notice © 2005 Wyse Technology Inc. All rights reserved. This manual is copyrighted. You may not reproduce, transmit, transcribe, store in a retrieval system, or translate into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, any part of this publication without express written permission.
FCC Statement This equipment has been tested and found to comply with the limits for either Class A or Class B digital devices (refer to "Thin Client Requirements Compliance"), pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
applicables aux appareils numériques de la classe B prescrites dans le Réglement sur le brouillage radioélectrique édicté par le Ministère des Communications du Canada. IEC/EN Notice These products conform to the requirements of IEC950 and EN60950. These products conform to requirements of EN55022 for Class A equipment or EN55022 for Class B equipment (refer to "Thin Client Requirements Compliance").
Contents Getting Started 1 Before You Begin 1 What’s In the Kit 1 Required Tools and Materials Associated Documentation 3 3 Installing the Option Kit 2 Install the kit in the 9450XE Install the kit in the 9455XL Install the kit in the 941GXL Verify Operation of the Unit 1 3 4 5
Getting Started This document describes how to install your 512 MB Flash Upgrade Option Kit into either Model 9450XE, 9455XL or J400, Product 941GXL Before you Begin Kit Warranty: The warranty on this kit assumes the remaining months of warranty of the unit in which it is installed or 90 days whichever is greater. Installation of this kit will not void the factory warranty however the user will be responsible for damage due to improper installation.
2 Chapter 1 Required Tools and Materials You need the following items before you can install. o #1 Phillips screwdriver Warning The Flash Module card may be susceptible to damage by Electro-static discharge. Take all reasonable precautions to avoid ESD. Associated Documentation o Winterm™ 9000 Series Quick Reference Guide http://www.wyse.com/products/winterm/reference/9series/883808-01C.pdf (3.62MB) 883808-01 Rev.
Installing the Option Kit This chapter will describe the procedures for installing the 512MB Flash Option kit in the model 9450XE, 9455XL or J400 Product 941GXL terminals. Installing the Kit into the 9450XE Platform Perform a proper shutdown of the terminal by ending your session and clicking the buttons as they appear. Unplug the power supply and remove all of the cables from the rear of the unit.
2 Chapter 2 Remove the plastic or metal IDE module retention bracket by removing the Philips screw. Figure 2 Figure 3 Remove the power cable from the flash module as shown in Figure 4 and carefully remove the flash module from the socket. Note the connector where the module is located. Remove the power cable connector and carefully remove the flash module from the IDE connector noting the location of the module.
3 Chapter 2 Installing the Kit into the 9455XL Platform Perform a proper shutdown of the terminal by ending your session and clicking the buttons as they appear. Unplug the power supply and remove all of the cables from the rear of the unit. Remove the top cover from the 9455XL using the following steps: Remove the top cover by removing the three screws applying pressure using the palm of your hand as shown in Figure 5.
4 Chapter 2 Remove the power cable from the flash module as shown in Figure 7 and carefully remove the flash module from the socket. Note the connector where the module is located. Remove the power cable connector and carefully remove the flash module from the IDE connector noting the location of the module. Figure 7 Install the 512MB Option kit into the 9455XL into the location of the original module. Plug the power cable into the module. Reinstall the CDROM bracket.
5 Chapter 2 Remove the IDE retention bracket if installed by removing the two screws, otherwise carefully cut the spot of hot glue at the base of the connector, then remove the power cable for the flash module as shown in Figure 9 below. Carefully remove the flash module carefully noting the location of the flash module in reference to the IDE connectors.
6 Chapter 2 Figure 10 Click on the “Start” and “About” links and the display will be as shown as below in Figure 11. Figure 11 The display will be as shown in Figure 12 below. Verify that the MAC address and Serial Number as displayed match the serial number and MAC address on the unit.
Figure 12 The unit is ready for operation and setup by the Administrator.
