User Guide

ManualsBrandsWyreStorm ManualsAVWyreStorm 4K AV over IP JPEG 2000 Encoder and Decoder

IMPORTANT! Installation Requirements

• Visit the NetworkHD product pages download section at wyrestorm.

com to check for the latest rmware, document versions, and WyreStorm

Management Suite conguration tools.

• Install the latest rmware onto all encoders and decoders using the

Maintenance Tool found in the Management Suite and via the NHD-000-

CTL web interface. Full rmware update instructions are included with the

rmware download.

• NetworkHD requires a Layer 2+ or Layer 3 managed switch network with

support for Multicast & IGMP snooping enabled.

• WyreStorm highly recommends using network switches listed in the

NetworkHD Switch Recommendation Guide. These switches have been

veried by WyreStorm to meet the requirements of a NetworkHD system.

• Congure all network switches to the exact specication of the guides at

wyrestorm.com prior to connecting any NetworkHD devices.

• NetworkHD uses stateless address autoconguration (auto-IP) to assign

link-local IP addresses in the range of 169.254.x.x to encoders and

decoders out of the box. Your PC must be set to an address in this range in

order to discover the encoders, decoders and NHD-000-CTL.

• WyreStorm recommends the use of the NHD-000-RACK4 for installations

containing multiple NetworkHD devices. Use of this product provides an

enclosure to mount and secure all NetworkHD devices in a standard 19-

inch rack frame (EIA-310).

NHD-400-E-TX | NHD-400-E-RX Quickstart Guide | 200709

UK: +44 (0) 1793 230 343 | ROW: 844.280.WYRE (9973)

support@wyrestorm.com

1 of 4

Basic Wiring Diagram

Wifi Router

Personal Computer

NHD-400-E-TX

NHD-400-E-RX NHD-400-E-RX NHD-400-E-RX

iPad with

NetworkHD Touch

NHD-400-E-TX

UHD Blu-ray Player

NHD-000-CTL

Control System

Key

Digital Video/DVI/HDMI

Ethernet

RS-232

Set Top Box

4K AV over IP JPEG 2000 Encoder and Decoder

NHD-400-E-TX | NHD-400-E-RX

Quickstart Guide

WyreStorm recommends reading through this document in its entirety to become familiar with the product’s features prior to starting the

installation process.

In the Box

1x NHD-400-E-TX or NHD-400-E-RX

1x 4-pin Terminal Block (RX only)

2x Mounting Brackets for NHD-000-RACK4

2x Wall Mounting Brackets

1x Quickstart Guide (This Document)

Additional Information

More information and required software can be found within the Download

section of the product page on wyrestorm.com.

• Management Suite v1.6 or Higher

• NetworkHD Switch Recommendations

• NetworkHD Switch Mapping Worksheet

• NetworkHD Switch Conguration Guides

• NetworkHD Touch Installation Guide

• NetworkHD Touch User Guide

• Drivers for Popular Control Systems

Summary of content (4 pages)

PAGE 1
4K AV over IP JPEG 2000 Encoder and Decoder Quickstart Guide NHD-400-E-TX | NHD-400-E-RX WyreStorm recommends reading through this document in its entirety to become familiar with the product’s features prior to starting the installation process. • Configure all network switches to the exact specification of the guides at wyrestorm.com prior to connecting any NetworkHD devices. IMPORTANT! Installation Requirements • Visit the NetworkHD product pages download section at wyrestorm.
PAGE 2
Wiring and Connections WyreStorm recommends that all wiring for the installation is run and terminated prior to making connections to the switcher. Read through this section in this entirety before running or terminating the wires to ensure proper operation and to avoid damaging equipment.
PAGE 3
NetworkHD Console Configuration In addition to the steps below more information on configuration can be found in the NetworkHD Installation Guide. 1. Ensure that a correctly configured network switch has been setup in advance. Guides are available from the WyreStorm website. 2. Connect a computer running Windows™ to the same LAN/VLAN as the NetworkHD components and ensure its IP is within the same subnet as the NetworkHD default 169.254.x.x IP addresses.
PAGE 4
Specifications Connectivity Encoder (TX) Decoder (RX) Inputs 1x HDMI IN: 19-pin HDMI Type A 1x LAN (PoE): 8P8C “RJ45” Socket ANSI/TIA-568 Outputs 1x LAN(PoE): 8P8C “RJ45” Socket ANSI/TIA-568 1x HDMI OUT: 19-pin HDMI Type A 1x RS-232: 4-Pin Phoenix Transmission Transmssion Encoding Proprietary stream encoding. Video compression based on JPEG 2000 End to End Latency With RX, 1 video frame (Passthrough mode) 2 video frames (scaling/video wall) e.g.