EX-1UTP-IR-50 50m/164ft HDMI Extension over HDBaseT incl. full 3D & Bidirectional IR EX-1UTP-IR-50-POH 50M/164FT HDMI Extension Over HDBaseT incl. Remote Power, full 3D & Bidirectional IR Instruction Manual Thank you for choosing this WyreStorm product. Please read these instructions carefully before installing to avoid complications later. Technical Support: support@wyrestorm.
CONTENTS, INTRODUCTION, FEATURES, AND FEATURES Contents of source and display from either location over distances of up to 50m/164ft using a single shielded or unshielded Cat5e/6 cable.
extender sets. 3. 3. WARNING WARNING reduce theofrisk fire, electric To To reduce the risk fire,ofelectric shock shock or or product damage: product damage: front e l of stems. m s er a 1ft) ures Safety Precautions Safety Precautions 1. Do not expose this apparatus to rain, moisture, sprays, 1.
PANEL DESCRIPTION - TRANSMITTER 6i. Panel Description - EX-1UTP-IR-50 Transmitter 1 2 3 1 2 5 3 4 7 6 EDID management – see Transmitter EDID Settings for details (section 9) IR RX Input – 3.5mm IR Receiver placed at display location to remotely control the source device. IR TX Output – 3.5mm IR Transmitter connecting to source device for control from display location.
1 2 3 1 2 5 3 4 7 6 Distance SETTING - see Receiver distance Settings for details (section 9) IR RX Input – 3.5mm IR Receiver placed at display location to remotely control the source device. IR TX Output – 3.5mm IR Transmitter connecting to source device for control from display location.
PANEL DESCRIPTION - TRANSMITTER 6ii. Panel Description - EX-1UTP-IR-50-POH Transmitter 1 2 3 1 2 5 3 4 7 6 12 9 8 10 EDID Management - see Transmitter EDID Settings for details (section 9) IR RX Input – 3.5mm IR Receiver placed at display location to remotely control the source device. IR TX Output – 3.5mm IR Transmitter connecting to source device for control from display location.
1 2 3 2 5 3 4 7 6 9 10 IR TX Output – 3.5mm IR Transmitter connecting to source device for control from display location. Signal LINK status – LED lit when signal detected 5 HDBaseT INPUT 6 Power indication – LED lit when powered 5v Power Input – optional: for use if power supply issues are experienced at Transmitter location. 8 Ground Point 9 HDMI OUTPUT 10 SETTING DIP Switch settings printed on base of SETTING 8 IR RX Input – 3.
Typical Application SOURCE DEVICE 6 COntrol System cat 5e cable up to 50m (164ft) TRANSMITTER 7 power NOTE: Although WyreStorm products are tested with Cat5e, we recommend Cat6 due to increased bandwidth and improved capacity for handling large transmissions and power along a single cable. Optional 5v power available on PoH model should power transmission issues be encountered from TRANSMITTER location RECEIVER 4 hdmi 5 ir tx cable DISPLAY OUTPUT 8.
NOTE A 5v power input is included on the Receiver for optional use should power issues be encountered at the Transmitter location. 9. EDID & Distance Setting Distribution of HD signals through devices requires mutual communication or ‘handshake’ between source and display. If there is any disparity between the two, successful transmission becomes problematic.
TROUBLESHOOTING 10. Troubleshooting Generally, the majority of HD distribution installation issues are either caused by minor connection errors, communication problems between devices, or when the transmission of high signal bandwidth is attempted using insufficient cable.
No sound or poor quality audio 13) Picture snow/HD ‘noise’ – represents a poorly established signal that may be caused by poor quality terminations or excessive cable lengths. Try swapping the display adaptors from a location you know is functioning properly or swapping the outputs of the matrix switch used.
FAQ’S flashlight to find s small sensor within the facia of the source display. If necessary, secure the IR eye over the sensor with a small amount of contact adhesive. 3) Is your remote powered and sending a signal? Note: IR is invisible to the naked eye, so use a digital camera/ phone camera to check the remote signal – point the camera at the remote control when pressing a button. You should see the remote transmittion diode flashing to indicate a signal being sent.
Do I need power at the TV end? Yes. Our HD display adaptors require a 5v power supply at the TV end to operate. It’s important that these are powered locally and do not receive remote power from the rack as there can be issues resulting from voltage drop along the length of cable. Our new USB power cables overcome the problem of having a second mains outlet behind the TV.
perform safety checks to confirm that the unit is in proper working condition. MAIL-IN-SERVICE, WARRANTY, LIMITS AND EXCLUSIONS 14. Mail-in-service When shipping the unit, carefully pack and send it prepaid, adequately insured and preferably in the original carton. Include a letter detailing the complaint and provide a daytime phone and/or email address where you can be reached.
Installation Notes INSTALLATION NOTES 17.
www.wyrestorm.com www.wyrestorm.com www.wyrestorm.
