Wyrestorm Extender Set Solutions Part Number EX-1UTP-IR-100-EDID Part Number EX-1UTP-IR-100-POH HDMI® Extension over Cat5e/6/7 with Full HDBaseT™ up to 100m incl. bidirectional IR control, RS232 1:2 HDMI splitting capabilities, EDID management and Power-over-HDBaseT* Instruction Manual Thank you for choosing this Wyrestorm product. Please read these instructions carefully before installing to avoid complications later. Technical Support: support@wyrestorm.
CONTENTS AND INTRODUCTION Contents 1 Introduction 2 Features 3 Safety Precautions 4 Packaging Contents 5 Panel Descriptions i. EX-1UTP-IR-100-POH Transmitter ii. EX-1UTP-IR-100-POH Receiver iii. EX-1UTP-IR-100-EDID Transmitter iv. EX-1UTP-IR-100-EDID Receiver 6 Connection & Operation 7 EDID & Upgrade Switcher Instruction 8 Specification i. EX-1UTP-IR-100-EDID ii.
2. Features • Fully 3D compatible – Frame sequential 3D (Blu-ray) and • 2k resolution supported. interlaced stereoscopic 3D (satellite broadcasts etc.) extender sets. 3. 3. Safety Precautions Safety Precautions • Supports all high definition resolutions up to and including • True playstandard convergence realised with the inclusion 1080p5 and video formats. WARNING WARNING of Power-over-HDBaseT for distribution of video, • RS232 port.
PACkAGE CONTENTS AND EX-1UTP-IR-100-POH TRANSMITTER 4.
EX-1UTP-IR-100-POH Receiver 1 2 3 4 5 1 RS232 Port 2 LED HDBT Link Indicator (Lit for active) 3 HDBT IN 4 LED Power Indicator (Lit for active) 5 HDMI output 6 TCP/IP Connector 7 IR TX Transmitter port 8 IR RX Receiver port 5iii. 6 7 EX-1UTP-IR-100-POH TRANSMITTER AND EX-1UTP-IR-100-EDID TRANSMITTER 5ii.
EX-1UTP-IR-100-EDID RECEIVER AND CONNECTION & OPERATION 5iv. EX-1UTP-IR-100-EDID Receiver 1 2 3 4 5 1 RS232 Port 7 IR TX Transmitter port 2 LED HDBT Link Indicator (Lit for active) 8 IR RX Receiver port 3 UTP IN 4 DC 5V Power Input 5 HDMI OUT 6 TCP/IP Connector 6. 7 8 Connection & Operation Attention: Do Not Hotplug! - Please insert and extract cables carefully with the power switched off. Connecting and disconnecting cables while the unit is powered can damage circuitry.
EDID & UPGRADE SWITCHER INSTRUCTION 7 To enable LAN/internet content on your display device, connect an Ethernet cable from the Ethernet port on the RECEIVER to the corresponding LAN port on your display. 8 Insert the IR receiver 3.5mm jack into the IR RX port on the RECEIVER. Attach the IR receiver to the front of your display with the adhesive backing, ensuring there is clear line of sight to the remote control being used. You may need to adjust the position of the IR Receiver to achieve best results.
i. Specification (EX-1UTP-IR-100-EDID) SPECIFICATION AND TYPICAL APPLICATION 100m/328ft Mass (Per Main unit) 8ii. (Each) Specification (EX-1UTP-IR-100-POH) sync) sync) 100m/328ft 12VDC 17 Watts Max (Pairs with EX-1UTP-IR-100-POH Transmitter) 145mmWx106mmDx29mmH/5.71”Wx4.17”Dx1.14”H (Transmitter) 130mmWx106mmDx29mmH/5.11”Wx4.17”Dx1.14”H (Receiver) 0.86kg / 1.87lbs (Each) NOTE: Specifications are subject to change without notice. Mass and dimensions are approximate. 9.
2. Gently move the jumper caps to the ‘Update’ position to allow upgrade through the RS232 port. 3. Connect USB - Serial Cable to PC and run VS100 RX Firmware Update batch file 4. Once update has been completed, be sure to return the jumper caps to the ‘Normal’ position for RS232 control signal transmission to be passed. Note: Connect RS232 cables to the RS232 ports of the EX-1UTP-IR-100-POH Transmitter and the Receiver to form one extension cable. 10.
MAINTENANCE, PRODUCT SERVICES, MAIL-IN-SERVICE AND WARRANY LIMITS AND EXCLUSIONS 11. Maintenance Clean this unit with a soft, dry cloth only. Never use alcohol, paint thinner or other harsh chemicals. 12. Product Services Provided Service: 1. Damage requiring service: This unit should be serviced by a qualified service personnel if: • The DC power supply or AC adaptor has been damaged. • Objects or liquid have gotten into the unit. • The unit has been exposed to rain.
INSTALLATION TEST NOTES 2. There are no express warranties except as listed under “limited warranty coverage.” The warrantor is not liable for incidental or consequential damage resulting from the use of this product or arising out of any breach of this warranty. For example: damages for lost time, the cost of having a person/persons remove or re-install previously installed equipment, travel to and from service location, loss of or damage to media, images, data or other recorded/stored content.
www.wyrestorm.com www.wyrestorm.
