Instruction Manual

10
HYDRAULIC VIBRATOR ASSEMBLY PARTS LIST
PART UMBER
ITEM QTY U/M DESCRIPTIO STRAIGHT
949-100
AGLE
949-170
1 1 EA SQUARE Head Housing with Lower Bearing Cup
589-400 589-400
2 1 EA Hex Nut
432707 432707
3 1 EA Washer
887011 887011
4 4 EA Bearing
419661 419661
5 2 EA Shim
419697 419697
6 1 EA Rotor
719660 719660
7 1 EA Upper Bearing Cup, Slotted
419668 419668
8 1 EA Spacer
419666 419666
9 1 EA Driver Sleeve
419659 419659
10 1 EA Driver
419656 419656
11 3 EA Socket Head Cap Screw (No. 10-32 x 7/8 inch long)
419660 419660
12 3 EA Lock Washer (No. 10 split ring)
415362 415362
13 1 EA Hydraulic Motor Housing
589404 589403
14 1 EA Hydraulic Motor
418-000 418-000
15 1 EA Hydraulic Hose Assembly (1/4 hose with 1/4 NPT male threads) 8’
- 212508
16 1 EA Hydraulic Hose Assembly (3/8 hose with 3/8 NPT male threads) 8’
- 213708
17 1 EA Angle Mounting Bracket
- 419771
18 2 EA Hex Head Bolt
- 439712
19 4 EA Lock Washer(1/2 inch split ring)
- 439704
20 4 EA Hex Nut (1/2-13)
- 439703
21 1 EA Isolator
- 419720
23 1 EA Clamp
- 419729
24 2 EA Hex Head Bolt (1/2-13 x 3-1/2 inch long)
- 439708
25 1 EA Rubber Plug, Tapered
- 419684
26 1 EA Punch Lock Clamp
- 259601
27 4 FT Protective Hose
- 219500
28 1 EA Name Plate
669600 669600
29 1 EA Hose Clamp (No. 36)
- 259611
30 1 EA Rubber Plug (No. 11), Straight
419685 419685
31 1 EA Quick Disconnect Set
419692 419692
32 6 FT Protective Hose
219500 -
33 3 EA Hose Clamp (No. 36)
259611 -
34 1 EA Hydraulic Hose Assembly (1/4 hose with 1/4 NPT male threads) 9’
212509
-
35 1 EA Hydraulic Hose Assembly (3/8 hose with 3/8 NPT male threads) 9’
213709
-
MOTOR SPECIFICATIOS AD HYDRAULIC REQUIREMETS
DATA BELOW IS BASED IN 225 SSU HYDRAULIC FLUID
FLOW: 4 GPM
PRESSURE: 700 P.S.I.; Max. 1200 P.S.I. with oil at 130° F
INLET: ¼" NPT
OUTLET: 3/8" NPT
FILTRATION: 10 Micron Absolute (ISO 17/13 Fluid Cleanliness)
FLUID TEMP: 100° F Minimum; 180° F Maximum
OTE: A. DO OT OPERATE ABOVE 10,800 VPM
B. ALWAYS DISCOECT ILET (1/4) HOSE FIRST
C. TO ESURE PROPER HYDRAULIC MOTOR SEAL LIFE, MAITAI A BACK PRESSURE
TO THE MOTOR OF LESS THA 50 PSI.
D. MALE AD FEMALE QUICK DISCOECTS MAY BE O EITHER THE PRESSURE OR
THE RETUR LIE. ALWAYS CHECK THAT THE SMALLER DIAMETER HYDRAULIC
HOSE IS THE PRESSURE HOSE.