Specifications

paint and silk
print products)
wrapped dust-free cloth) wet 95%
alcohol pressure in the sample,
wiped back and forth, and the test
distance is about 20 mm. There is
no hair loss, juboate, and dew in
the test.
Spray paint, silk screen 50 laps:
UV, PU paint 100 laps:
The injector is no color,
the fuel injection, no
leakage of the bottom
after melement resistance,
and the silk screen is
free, and it is clear.
(Refer to our remote
control quality
specification
requirements)
4.2.3
铅笔硬度测试（针
对普通漆产品）
Pencil hardness
test (for
ordinary paint
products)
将铅笔装在专用的铅笔硬度测试仪上(载重
750g，铅笔与水平面的夹角为 45°)，推动铅
笔 5mm 距离，共划 5 条(不同位置)，再用橡
皮擦将铅笔痕擦拭干净。没有涂膜损伤痕迹，
允许起始位置的微小压痕。
普通漆 HB 硬度；UV 漆 2H 硬度。
Put pencils on a dedicated pencil hardness tester
(750g, the pencil and the horizontal angle of
45 °), push the pencil 5mm distance, coexist 5
(different positions), and then wipe the penar
marks clean. There is no trace of coating damage,
allowing minimal indentation of the starting
position.
Ordinary paint HB hardness; UV paint 2H
hardness.
不可磨穿涂层，不可露底漆，不可
露底材。丝印无断笔、擦花、褪色
等缺陷。无断笔、擦花、褪色等缺
陷。（参照我司遥控器质量规
范要求）
Do not polish the coating, can not be
reversed, and the substrate is not
optimized. Silk screen is free, wipe,
faded and other defects. No
shortcomings, wipe, fading and other
defects. (Refer to our remote control
quality specification requirements)
4.2.4
橡皮耐磨测试（针
对普通漆及丝印产
品）
Rubber wear test
(for ordinary
paint and silk
printing
products)
用载重 500g 的实验棒底部装上 FABER-
CASTELL 7017R 橡皮，以 40 次/min 的速度来
回擦拭，测试距离 20mm 左右。表面无明显退
色、透底（露出底材）。
丝印 30 圈：UV、PU 漆 100 圈：
The Faber-Castell 7017R eraser is loaded with a
500g experimental rod, wiped back and forth at a
speed of 40 / min, and the test distance is about
20mm. There is no obvious surface of the
surface, and the bottom (exposed substrate).
Silk print 30 laps: UV, PU paint 100 laps:
无起皮，漏底材现象；丝印件无丝
印断笔，无擦花，清晰可见为合
格。（参照我司遥控器质量规
范要求）
There is no skin, leakage bottom
phenomenon; silk screen wireless
screen pen, no polish, clear and
clearly qualified. (Refer to our remote
control quality specification
requirements)
4.2.5
3M 胶纸测试（针
对丝印）
3M adhesive test
(for silk
screen)
用 3M600 胶带完全粘合丝印的区域，将胶带
呈 45°角 1 秒内撕起。粘揭 3 次，每次使用
新胶带。
The tape is torn within 1 second in a 45 ° angle
with a 3M600 tape. Paste 3 times, using a new
tape each time.
第一、二次不能掉丝印漆第三次脱
落油漆面积≤ 5 %（参照我司遥控器
质量规范要求）
First, secondary unable to pull the silk
printing, the third declined paint area
is ≤ 5% (refer to our remote control
quality specification requirements)
4.2.6
耐化妆品测试（丝
印）
Cosmetic test
(silk screen)
将 Nivea cream 涂于印刷图案上, 覆盖欲测试
印刷图案 15*15mm，静置 24 小时后，擦拭干
净，进行外观检。
Applying NIVEA CREAM to the print pattern,
covering the test print pattern 15 * 15mm, after
standing for 24 hours, wiping clean, perform an
external examination
擦拭纱布上不可沾有印刷油墨
印刷图案应清晰可辨识、不可剥落
及断线。（参照我司遥控器质量规
范要求）
No printing ink on the wiping gauze
The printed pattern should be clearly
recognized, non-peeling and
disconnection. (Refer to our remote
control quality specification
requirements)
4.2.7
耐人工汗测试（丝
印）
Practice sweat
测试条件：a)、测试溶液成分为：纯净水
400ml、氯化钠 8g、氯化铵 7g,、尿素 2g、醋
酸 1ml、 乳 酸 6ml、少许氢氧化钠，
PH=4.7；b)、将浸泡溶液的滤纸贴在样品表面
及背面，把产品密封在滤纸中，然后置于温度
判定标准：滤纸不允许有染色，外
表面不允许有腐蚀和脱层的现象为
合格。（参照我司遥控器质量规范
要求）
Judgment Standard: The filter paper is