Specifications

horizontal vertical axis distance of the light point, the
horizontal vertical axis distance of the spot is 0.5 m, the
pressing remote control is transmitted to the infrared light
signal. Line IR POWER ≥ 40uw / cm2, left and right levels 30 °,
IR POWER ≥ 20UW / Cm2.
4.1.2
遥控距离
Remote control
distance
遥控直线距离≥8 米
水平左右方向45°距离≥5米， 垂直上下方向45°，距离≥5米
Remote line distance ≥8 meters
The horizontal direction 45 ° distance is ≥5 meters, vertically
45 °, distance ≥ 5 meters
4.1.3
动态电流
Dynamic current
控器的电源电压为额定工作值，瞬间按压任意功能键时，用电流表测量工
作电流≤30mA。
The power supply voltage of the controller is a rated working
value. When the current is pressed, the operating current is
measured with the current table to measure the operating current
≤ 30 mA.
4.1.4
静态电流
Quiescent
Current
测量静态电流。平均值为：≤3uA
Measuring the static current. The average value is: ≤ 3ua
4.1.5
高低工作电压测
试
High and low
work voltage
test
在2.4V-3.6V电压范围内，要求在功能正常。（包括能正常学习、遥控）
During the 2.4V-3.6V voltage range, it is required to function
properly. (Including normal learning, remote control)
4.1.6
遥控器按键电池
寿命实验
Remote control
button battery
life experiment
将遥控器装入电池放在按键寿命测试仪上，按 100 次/分钟和 300g 压力
测试50万次,取下后能正常工作；
Put the remote control into the battery is placed on the button
life tester. Press 100 / minute and 300g pressure to test 500,000
times, and will work properly after removal;
4.1.7
放电测试
Discharge test
空气电压=±8K 伏,接触放电=±4K 伏,电容：150PF ，电阻：330Ohm 功能
及部件无损坏。
Air voltage = ± 8K volts, contact discharge = ± 4K volts,
capacitance: 150pf, resistance: 330OHM function
And parts are not damaged.
4.1.8
电池辐射抗干扰
及电池辐射EM
Battery
radiation anti-
interference
and battery
radiation EM
根据EN 55013,EN61000.-4-2,EN61000-4-3, 。Refer to
EN55013,EN61000.-4-2,EN61000-4-3。
According to EN 55013, EN61000. -4-2, EN61000-4-3,. REFER TO
EN55013, EN61000. -4-2, EN61000-4-3.
4.1.9
红外线载波频
Infrared
carrier
frequency
用PC 测试仪, 载波频率为：38kHZ±500Hz。 36kHZ±500Hz
With a PC tester, the carrier frequency is: 38kHz ± 500 Hz. 36kHz
± 500Hz
4.1.10
电池反接
Battery
反装电池 1min 后，拔下电池，重新以正确的方式装入电池，检
测遥控器工作状况，遥控器能正常工作，反装测试不导通。
After the battery is 1min, unplug the battery, re-put the battery
in the correct way, check
The operating conditions of the remote control, the remote
control can work properly, and the reverse test is not turned on.