D101 Operation Manual
01 Basic Parameters Basic Usage Display of Indicator Light Guide to APP Usage FAQ Cleaning Steps Precautions Warranties 02 04 08 09 13 20 22 25
02 Basic Parameters Model D101 Color White Material ABS Printing resolution 203dpi Printing speed 30mm/s~60mm/s Label width 10~25mm Printing method Effective printing width Applicable paper types Thermal printing 24mm Adding machine paper and transparent paper
03 04 Accompanying supplies One warranty card, one type-C data cable Barcode printing Supports barcodes and QR codes Battery type and capacity 1200mAh lithium battery Connection mode Printing content Bluetooth Text/patterns/designs Charging duration 3~4 hours Charging interface Type-c Voltage of incoming current Battery life 5V-1A 4 hours of continuous printing
05 04 Basic Usage Slide to the left to open the lid �. Slide to the left to open the lid 90° �.
02 05 06 Paper case baffle �. Requirements for installation of paper case baffle (the baffle has been installed before delivery, and can be used directly for ��mm backing paper labels, but should be removed for ��mm backing paper labels).
03 06 Right Left �. Installation of consumables: Insert the roll of paper on the right, with the printing surface facing the switch.
07 Slide to the right end �.Close the lid, and slide to the right end About the new machine: NIIMBOT label printer is generally charged before the delivery for the startup. If you cannot start up your new printer, one possible reason is low battery level. The printer can be started up after being charged for 20 minutes.
08 Indicator Light Descriptions Indicator light color Light status Blue Slow flash Bluetooth not connected Blue Quick flash Printing or charging Blue Not flashing Red Slow flash Red Quick flash Red Not flashing Description Bluetooth connected, battery fully charged Bluetooth not connected and low battery level Printing, or charging and low battery level Bluetooth connected, low battery level
09 Guide to App Usage It only takes two steps to start a new marking experience Download the "NiiMbot" application from the App Store or Google Play.
10 Bluetooth connection mode On your phone or device, turn Bluetooth on. Then start up the printer, and open the app. Switch Screenthe Bluetooth Switch on Mirroring Long press the switch button to activate the label printer Press the [Not Connected] button on the right corner of the app, and then click [Search Device].
11 3 Press the blue [Match] button to the right of the correct printer model, and Bluetooth will connect.
12 Uagse & Operation Press the [Usage Demo] button on the right corner of the app to choose from the demo videos that can be played in the list of [Software Instructions]. 9:41 AM 精臣云打印 100% 教程 行业模板 教程 视频操作教程 GO 查看 精臣珠宝标签纸...
13 FAQ Q: Why can’t the label printer be fully charged when it is connected to a laptop for charging, and why does it switch off automatically after being disconnected? A: The laptop's USB port does not have a sufficient and stable enough voltage to ensure stable charging conditions. Please charge the label printer using a normal power socket. Q: Is the registration of an account necessary in order to use the label printer? A: The label printer can be used even if you do not register an account.
14 Q: Does the label printer support auto-shutdown? A: The label printer will shut down automatically after Bluetooth has been disconnected or the app logged out for 15 minutes, to save power and protect battery life. Q: Why does the label printer keep printing blank labels when working normally? A: It is possible that the label paper has been placed in the wrong direction. Please keep the label’ s sticker face down (facing the power button).
15 Q: Why is my label printer just continuously delivering large amounts of label paper? A： 1、There may be label paper on the upper cover detector, leading to a failure to detect the paper. 2、There may be label paper on the print head, leading to a failure to detect the paper. 3、The size set by the template may not be consistent with the actual size of the label paper. 4、The set paper type of the template may be wrong.
16 Q: What should I do if the app prompts me to use non-universal labels after the label paper is placed in the machine? A： 1、The D101 label printer currently is only applicable to the special label papers in the D101 series. Using the label papers of other brands will lead to failure. 2、There may be a foreign object in the paper case covering the sensing port, leading to failure to identify the paper, so you may only need to remove the foreign object from the paper case.
17 A： 1、If the machine is charging, and the mobile phone fails to find the label printer using Bluetooth, simply unplug the power cord. 2、If Bluetooth response is slow, restart the software or restart the printer and try to connect again. 3、If it is caused by a software version issue, uninstall and reinstall or contact technical personnel. Q: Does the label printer support batch printing, and how many paper sheets can be printed at a time? A: D101 supports continuous printing and batch printing.
18 Q: App error, the prompt says "lack of paper" A: It is most likely one of the following possibilities: 1. No paper is placed in the machine 2. The paper case baffle is not installed or the paper case baffle is not installed in its proper place for 15mm backing paper labels. 3.Machine fault. Q: After pressing "Print", no content appears, and the machine keeps sending out "clack" sounds.
19 Q: How can I make it so that the content is placed in the middle when editing the label? A: On the right side of the edit page’s [Style] section, where there is a button to the left or the right with the content in the middle, press this button to adjust the position of the label content in the edit box. You can adjust the position of the text box on the label paper through the [Alignment].section.
20 Cleaning Steps In order to clean the platen, follow these steps: 1.Shut down the printer; 2.Open the paper case cover and find the print head (as shown in the figure). In case of printing having just finished, wait for the print head to cool completely; 3. While rotating the roller, wipe off the dust and stains on the surface of the roller with an alcohol cotton ball (which should be wrung out); 4.
21 Print head Notes: （1）Ensure the printer is powered off during daily maintenance; （2）Do not touch the surface of the print head with your hands or with metal objects, and do not scratch the surface of the print head, roller or sensor with tweezers; （3）Do not wipe the print head and roller with gasoline, propanol or other organic solvents; （4）After the alcohol has evaporated completely, turn on the power and continue printing.
22 Precautions 1.Please keep the product and its accessories in a safe place that is out of the reach of children to keep them out of harm’s way. 2.Please do not open the paper case cover when the printer is printing. 3.Please ensure that the paper case is clean before using the printer. Any foreign matter in the paper case may damage the print head during printing. 4.In case of any foreign matter being present, please use a special cleaning device or alcohol to clean the paper case and print head.
23 6.Please do not disassemble the printer without authorization. When the printer is disassembled, return and exchange will not be accepted. 7.Do not use the power adapter when the power cord is damaged, otherwise, it may result in electric shocks, fire and power adapter damage. 8. After continuous printing for a long time, the print head may be still hot. Do not touch the print head to avoid being burned. 9. Please use our original printing paper.
24 11. Please charge the battery in a cool and ventilated room. Do not expose the printer and power adapter to high temperature or high humidity, or put them in water, so as to avoid short circuiting, which may cause heat, smoke, or deformation damage, or even the explosion of the battery. If the power adapter comes into contact with water or other liquids, disconnect the power immediately.
25 Warranties 1.From the date of purchase, the warranty period of the print head of the product is 3 months or the time when the printing distance reaches 30km (whichever comes first), and that of other parts is 12 months. 2.Carry-in service is adopted as the warranty method and users need to bring the product to the sales service center. 3. If a product beyond its warranty period needs to be repaired, please contact the after-sales service center and ask for paid parts for repair. 4.
26 Any damage caused by unauthorized disassembly and repair or modification. Print omissions caused by scratches on print head. Inconsistency of purchase record with the serial number of the machine under warranty. Any damage due to human factors or other force majeure.
Wuhan NIIMBOT Intelligent Identification Technology Co., Ltd. Address: Creative Workshop No. 5, Creative World, Yezhihu West Road, Hongshan District, Wuhan Technical support hotline: 400-860-8800 Website: www.niimbot.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
