TechBook in.k300 the essential spa keypad Bright LCD screen Spa function icons Affordable 9919-101218-D Rev. 02-2018 © Groupe Gecko Alliance Inc., 2018 All trademarks or registered trademarks are the property of their respective owners. Gecko Alliance 450 des Canetons, Québec (Qc), G2E 5W6 Canada, 1.800.78.GECKO www.geckoalliance.
Table des matières Warnings ������������������������������������������������������������������������������������������������������������������������������������������������������������������������� 2 Introduction ��������������������������������������������������������������������������������������������������������������������������������������������������������������������� 3 in.
Warnings WARNINGS: Before installing or connecting the unit, please read the following. FAILURE TO COMPLY WITH THE FOLLOWING WARNINGS MAY SIGNIFICANTLY SHORTEN THE PRODUCT’S LIFE TIME, AND LEAD TO FAILURES AS WELL AS HAZARDOUS CONDITIONS*. COMMON SENSE MUST ALWAYS PREVAIL WHEN EVALUATING THE INSTALLATION AND/OR USE OF ANY ELECTRONIC CONTROL IN A FINAL APPLICATION. • RESPECT ENVIRONMENTAL CONDITIONS LISTED AT END OF TECHBOOK. • THIS UNIT MUST BE INSTALLED BY QUALIFIED PERSONNEL.
Introduction in.k300 the essential spa keypad The in.k300 brings all the features you really need to one keypad. Compact, with a big LCD screen; bright enough to be seen in day, simple enough to use in the middle of the night; affordable, yet solidly built. Item Static LCD size (as measured diagonally) in.k300 1.
in.k300 keypad layout 1 Pump Model 2 Pump Model Pump 1 Light Indicator lights Smart Winter Mode Pump 1 Pump 2 Up Down Light Indicator lights Up / Down Heater Filter Set Point in.k300 dimensions Installation of in.k300 Gasket with or without adhesive 2.25" (57.15 mm) 6.30" (160.02 mm) Optional wing nuts and spacers 1.87" (47.45 mm) To install the in.k300, use the drilling template provided in this section. Determine the mounting location and stick the template on chosen location.
Drilling template 36,58 mm 144,02 mm 131,32 mm R 6,35 mm R 6,35 mm 5
Installation notes Keypad placement Vent hole on back of keypad should not be blocked. The back of the in.k300 should not be enclosed where water can gather, but instead cut out. It is recommended to install the in.k300 on the outside edge of the hot tub, so that it is not subject to moisture trapped by the cover. Connecting in.k300 keypad to the spa pack Main keypad in.k300 Main keypad in.k300 6 in.xe & in.xm 2 in.ye & in.yt To connect the in.k300 keypad, simply insert its in.
Keypad functions Start or stop accessories To start or stop an accessory, press the associated button. Indicators will light up when the associated accessory is on. When an accessory has more than two states, press the button until it reaches the desired state. Indicators will flash when dual speed pumps are on at low speed, and will be solid at high speed. If you have a blower it will be controlled by the Pump 2 key.
Programming steps Program menu The program menu is accessible by holding down the Light key for 5 seconds. In the program menu the following parameters can be set: clock, filter or purge cycles, economy mode and temperature units. While in the program menu, use the Up or Down key to adjust the parameters and use the Light key to jump to the next parameter. The changes will be saved after the confirmation of the last parameter only.
Programming steps Setting filter or purge cycle start time The display will show FSxx, “xx” representing the starting hour of the cycle. Use the arrow keys to adjust the hours. Use the Light key to jump to the next parameter, filter duration (Fd). Setting filter cycle duration (not available on purge systems) The display will show Fdxx, “xx” representing the duration in hours of the filter cycle. Use the arrow keys to adjust the duration.
Programming steps Setting economy duration* The display will show Edxx, “xx” representing the duration in hours of the economy mode. Use the arrow keys to adjust the hour. Use the Light key to jump to the next parameter, temperature unit. 24 = continuous economy Setting temperature unit Water temperature can be displayed in either Fahrenheit (°F) or Celsius (°C). The display will show °F or °C. Use the arrow keys to change the setting. Use the Program or Light key to save all the parameters.
Error messages The list below shows the different error messages that can appear on the home screen. Refer to the troubleshooting and error codes section of the TechBook for your spa pack for more details. Code Message HL Warning! HL Error FLO No flow for more than 2 hours FLO No flow condition HR Danger! Relay stuck OH Warning! Spa temp. high Prr Warning! Temp. probes defective AOH Internal pack temp.
Specifications Part number 1 pump model: 0607-008036 2 pump model: 0607-008037 Model IN.K300-CL-GE1 Environmental Operating temperature: Storage temperature: Humidity: Water ingress protection: -68°F (-20°C) to 149°F (65°C) -22°F (-30°C) to 185°F (85°C) Up to 70% condensing IPX-5 Mechanical Weight: Dimensions (W x H x D): 0.69 lb (313 g) 2.25” x 6.30” x 1.87” (57.15 mm x 106.02 mm x 47.45 mm) Compatibility in.yj, in.yt, in.ye, in.xe, or in.
TechBook in.k300 the essential spa keypad Bright LCD screen Spa function icons Affordable 9919-101218-D Rev. 02-2018 © Groupe Gecko Alliance Inc., 2018 All trademarks or registered trademarks are the property of their respective owners. Gecko Alliance 450 des Canetons, Québec (Qc), G2E 5W6 Canada, 1.800.78.GECKO www.geckoalliance.