Assembly Instructions Caution: You should read this carefully before you proceed Sofa Page 1 OF 10
Parts List Label Picture Description QTY A Backrest 1 B Back cushion 2 C Left Armrest 1 D Right Armrest 1 E Seat 1 F Seat Cushion 2 G Sofa Leg 4 H Middle Support Leg 1 Page 2 OF 10
Hardware Label Picture Description QTY ① Bolt (M8*70MM) 11 ② Washer 19 ③ Bolt (M8*30MM) 9 ④ Allen Key 1 ⑤ Spring Washer 19 ⑥ Gasket 2 Assembly Preparation Before Beginning Assembly: X 11 X 19 X9 X 19 Page 3 OF 10
Assembly Steps Overview Backrest (A) Back cushion(B) Right Armrest (D) Left Armrest (C) Seat (E) Sofa Leg (G) Middle Support Leg(H） Seat Cushion (F) Sofa Leg (G) FRONT FACING This Sofa has multiple parts and may require up to 60 minutes to assemble. To give you an overview of the Sofa parts, the above picture is provided to help you put the various parts into perspective. Please read through the instructions below to familiarise yourself with the parts and steps before assembly.
Step 1 Left Armrest (C) Seat (E) Right Armrest (D) Seat (E) Open the carton and place all the parts on a clean, non-marring surface. With the assistance of your partner, attach the Seat(E) to the Armrests(C&D) with Bolts(①), Spring Washers(⑤), and Washers(②), using the Allen Key(④) as pictured above. Assistance from an adult partner is needed for this assembly process. Tighten the Bolts fully in a sequential manner. DO NOT fully tighten a Bolt in one go and then move on to the next.
Step 2 Left Armrest (C) Backrest (A) Tapered Connectors on Backrest Tapered Connectors on Armrest Right Armrest (D) Seat (E) 2.1 2.2 With the assistance from your adult partner: 2.1) Lift the Backrest(A) up, make sure the Backrest(A) is vertical and aligned to the Seat and Armrests. Align the Tapered Connectors on the Backrest(A) with those on the Armrest(C&D). Your adult partner may need to push the Armrests inwards to the Backrest(A) to allow for better alignment.
Step 3 Seat (E) Tilt and lay the Sofa on its Backrest(A) onto a flat surface. Attach the Seat(E) to the Backrest(A) with Bolts(①), Spring Washers(⑤), and Washers(②), using the Allen Key(④) as pictured above. Tighten the Bolts fully in a sequential manner. DO NOT fully tighten a Bolt in one go and then move on to the next. Rather, In a sequential manner, gradually tighten each Bolt until all Bolts are evenly secured. This methodology will ensure maximum evenness once all Bolts are fully tightened.
Step 4 Use Gaskets (⑥) to achieve stability Sofa Leg (G) Middle Support Leg(H） Sofa Leg (G) Install each of the Sofa Legs(G) to the bottom of the sofa using Bolts(③) ，Spring Washers(⑤), and Washers(②) with the Allen Key(④) as pictured above. Install the Middle Support Leg (H) by placing one Gasket(⑥) on the threaded stem. Then insert threaded stem into the threaded mounting postion in the middle of the Sofa. Tighten by turning the Leg clockwise.
Step 5 Back cushion(B) Seat Cushion (F） Place the sofa in an upright position, then Place the Seat Cushions(F) and the Back Cushion (B) onto the Sofa. Your Sofa is ready for use. This Sofa can only be used on a flat, level surface.
Page 10 OF 10
