Assembly Instructions

IMPORTANT:
• ALL INSTALLATION WORK SHOULD BE DONE BY ACCREDITED PROFESSIONAL.
• SHUT OFF POWER SUPPLY AT FUSE OR CIRCUIT BREAKER!
• USE ONLY THE SPECIFIED BULBS. DO NOT EXCEED THE MAXIMUM WATTAGE!
For Customer Service, please
contact the place of purchase.
Remove all of the contents from the carton. See
the important notes above. Shut off the power
at the circuit breaker and completely remove
the old xture from the ceiling, including the old
mounting strap.
1. Take the mounting strap assembly from the parts
bag. Mounting strap (B) contains several threaded
holes. Two of mounting screws (A) should be
attached to mounting strap (B). You may need to
tighten nuts (C) which hold these screws in place.
If the screws are not attached, please hold canopy
(F) up to mounting strap (B). Line up the holes in
canopy (F) with the holes in mounting strap (B) and
insert mounting screws (A) into mounting strap
(B) so that mounting screws (A) protrude through
the holes in canopy (F). Mounting screws (A) are
long, please test the canopy against the mounting
strap to see how far you should insert the screws.
Tighten nuts (C) onto mounting screws (A) to hold
the screws in place.
2. Pull the house wires through the center of
mounting strap (B). Place mounting strap (B)
over the junction box so that mounting screws
(A) are in alignment with the hole locations on the
xture’scanopy(F).Securemountingstrap(B)to
the junction box with mounting screws (D) and a
screwdriver. Tighten the screws securely.
CLEANING TIPS
Treat the xture gently! Regular cleaning will reduce the need for deep cleaning. For regular cleaning, turn off the light and wipe down the
xture with a clean lint-free cotton or microber cloth. Never spray cleaner directly onto the xture.
How to Identify the Fixture’s Wires
Hot Neutral Ground
Smooth
Ribbed
Bare Metal,
Green, or
Green Inner
Thread
Black
White
Black Inner
Thread
White Inner
Thread
House Wires
Fixture Wires
Hot
FINISHING THE INSTALLATION
8.Placethexture’scanopy(F)overmountingscrews(A)sothattheyprotrudethroughtheholesincanopy(F).Threaddeconuts(G)onto
mounting screws (A).
9.Installlightbulbs(notprovided)inaccordancewiththexture’sspecications.Donotexceedthemaximumrecommendedwattage.
Yourinstallationisnowcomplete.Turnonthepowerandtestthexture.
CONNECTING THE WIRES
7.Haveanassistantsupportthexture’sweightwhilecompletingthewiring.Refertothewiringdiagram
andattachthexture’swirestothepowersupplywiresfromthejunctionbox.ConnectHottoHot,Neutral
to Neutral, and Ground to Ground. Twist the ends of the wire pairs together, and then twist on a wire
connector. Make sure all twists are in the same direction. If there is no house ground wire coming from the
junctionbox,locategroundscrew(E)onthemountingbracket/mountingstrapandwrapthexture’sground
wire around the ground screw. Use a screwdriver to tighten the top of ground screw (E) onto the wires and
into the mounting bracket/mounting strap. Tuck the wires into the junction box.
PREPARING FOR INSTALLATION
ASSEMBLE THE FIXTURE
3. Refer to the “Step 1” diagram. Frame (L) is composed of four panels (1 and 2). The panels are two different sizes. Use small screws (T) to
attach brackets (S) to both of panels (1). Slide panels (2) over the ends of the now connected panels (1) so that the holes in panels (2) line up
with the holes in panels (1). Use screws (R) to secure the panels together. Frame (L) should look like the “Step 2” diagram when completed.
4.Placeframe(L)onitssideonaatsurface.Carefullyplacethelampbody(K)intothecenterofframe(L).Pushposts(M)throughthe
holesinbrackets(S).Thereare3optional12inchrods(I)and1optional6inchrod(J)includedforeachsideofthexture.Decidehowlong
youwouldlikethexturetohang.Bymeasuring,determinethecorrectnumberofrodsneeded.Tolengthenthexture,youcancontact
theplaceofpurchasetoorderadditionalrods.Thexture’swireswillrunthroughonesetofrods.Sliderods(Iand/orJ)ontothewires.
5. Pull the wires taut before threading rods (I and J) together. Thread bottom rod (J or I) onto posts (M) of the assembled frame (L). Twist
thetoprod(IorJ)intothethreadsofswivelpost(H).Pullthexture’swiresthroughswivel(H)andcanopy(F).Trimthewirestothedesired
length adding at least 8 to 10 inches of wire.
6. Place plate (Q) inside canopy (F) and the canopy over the tops of swivels (H). Twist on washers (P) and hex nuts (O) to secure the plate
and canoyp to the top threads of swivels (H).
A
G
N
D
B
C
D
E
F
G
I
K
H
L
J
M
N
O
P
R
Q
T1
S
S
2
Step 1
Step 2
R
2
1
S
S
T
L
L
Assembly Instructions