Assembly Instructions

Assembly Instructions
IMPORTANT:
• ALL INSTALLATION WORK SHOULD BE DONE BY ACCREDITED PROFESSIONAL.
• SHUT OFF POWER SUPPLY AT FUSE OR CIRCUIT BREAKER!
• USE ONLY THE SPECIFIED BULBS. DO NOT EXCEED THE MAXIMUM WATTAGE!
For Customer Service, please
contact the place of purchase.
PREPARING FOR INSTALLATION
Note: This xture may be mounted close-to-ceiling as a semi-ush or with rods as a pendant. These are pendant directions.
Remove all of the contents from the carton. See the important notes above. Remove the old xture from the ceiling, including the old
mounting strap.
ASSEMBLING THE FIXTURE
3. Refer to the “Step 1” diagram. Frame (L) is composed of four panels (1 and
2). The panels are two different sizes. Center rod (N) is on the wires, but not
attachedtothexture.Screwcenterrod(N)ontopost(O)andthenconnectit
to the bottom of bracket (S). Use small bracket screws (P) to attach bracket (S)
withthexture’sbodyattachedtobothofpanels(1).Slidepanels(2)overthe
ends of connected panels (1) so that the holes in panels (2) line up with the holes
in panels (1). Use screws (T) to secure the panels together. Frame (L) should look
like the “Step 2” diagram when completed.
4.Centerrod(N)isonthewires,butnotattachedtothexture.Screwcenter
rod (N) onto post (O) and then connect it to the bottom of bracket (S). There are
3 optional 12 inch rods (I) and 1 optional 6 inch rod (J) included. Decide how
longyouwouldlikethexturetohang.Bymeasuring,determinethecorrect
numberofrodsneededforproperhangingheight.Tolengthenthexture,you
can contact the place of purchase to order additional rods. Slide rods (I and/
orJ)ontothexture’swires.Pullthewirestautbeforethreadingrods(IandJ)
together. Thread bottom rod (J or I) onto post (M) of the assembled frame (L).
Twistthetoprod(IorJ)intothethreadsofswivelpost(H).Pullthexture’swires
through swivel (H) and through canopy (F). Trim the wires to the desired length
adding at least 8 to 10 inches of wire.
CONNECTING THE WIRES
5. Haveanassistantsupporttheweightofthexture.Refertothewiring
diagramandattachthexture’swirestothepowersupplywiresfromthe
junction box. Connect Hot to Hot, Neutral to Neutral, and Ground to Ground.
Twist the ends of the wire pairs together, and then twist on a wire connector.
Make sure all twists are in the same direction. If there is no house ground wire
coming from the junction box, locate ground screw (E) on the mounting bracket/
mountingstrapandwrapthexture’sgroundwirearoundthegroundscrew.
Use a screwdriver to tighten the top of ground screw (E) onto the wires and into
the mounting bracket/mounting strap. Tuck the wires into the junction box.
FINISHING THE INSTALLATION
6.Placethexture’scanopy(F)overmountingscrews(A)sothattheyprotrude
through the holes in canopy (F). Thread deco nuts (G) onto mounting screws (A).
7.Installlightbulbs(notprovided)inaccordancewiththexture’sspecications.
Do not exceed the maximum recommended wattage.
Yourinstallationisnowcomplete.Turnonthepowerandtestthexture.
1. Take the mounting strap assembly from the parts bag. Mounting strap (B) contains several threaded holes. Two of mounting screws
(A) should be attached to mounting strap (B). You may need to tighten nuts (C) which hold these screws in place. If the screws are not
attached, please hold canopy (F) up to mounting strap (B). Line up the holes in canopy (F) with the holes in mounting strap (B) and insert
mounting screws (A) into mounting strap (B) so that mounting screws (A) protrude through the holes in canopy (F). Mounting screws (A)
are long, please test the canopy against the mounting strap to see how far you should insert the screws. Tighten nuts (C) onto mounting
screws (A) to hold the screws in place.
2. Pull the house wires through the center of mounting strap (B). Place mounting strap (B) over the junction box so that mounting screws
(A)areinalignmentwiththeholelocationsonthexture’scanopy(F).Securemountingstrap(B)tothejunctionboxwithmountingscrews
(D) and a screwdriver. Tighten the screws securely.
House Wires
Fixture Wires
Hot
How to Identify the Fixture’s Wires
Hot Neutral Ground
Smooth
Ribbed
Bare Metal,
Green, or
Green Inner
Thread
Black
White
Black Inner
Thread
White Inner
Thread
CLEANING TIPS
Treat the xture gently! Regular cleaning will reduce the need for deep cleaning. For regular cleaning, turn off the light and wipe down the
xture with a clean lint-free cotton or microber cloth. Never spray cleaner directly onto the xture.
I
N
O
Q
A
G
N
D
B
C
D
E
F
G
H
J
L
M
L
M
S
M
L
2
1
1
S
T
R