Assembly Instruction Sheet

ManualsBrandsWrought Studio ManualsCandle-Style ChandeliersClabaugh 8 - Light Candle Style Tiered Chandelier with Crystal Accents

1of2

(8)B10CandelabraBaseBulbs60WMaximum

30-45minutes

Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtobesureallpartsare

present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.Contactcustomerserviceforreplacement

parts.

LightSource:

EstimatedAssemblyTime:

Preparation:

ToolsRequired:Flatheadscrewdriver, Phillips screwdriver,pliers,wirecutters,wirestrippers,electricaltape,safetyglasses.

Warnings and Cautions

Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.

These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly

recommend that a licensed, professional electrician perform the installation.

Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.

Package Contents

Crossbar Assembly

6” Rod

12” Rod

Ceiling

Canopy

Supply Wires

and Ground Wire

Fixture Body

STEP 2 Install Crossbar Assembly-

A. Pass the supply wires through the Crossbar Assembly (A). Attach

the Crossbar Assembly (A) to the Outlet Box with the head of the

Green Ground Screw facing you. Secure it with Outlet Box Screws

(not included). Tighten until snug

Supply Wires with

Ground Wire

Outlet Box Screws

(not included)

Outlet Box

Figure 2

STEP 3 Test Fitting Ceiling Canopy to Crossbar Assembly-

Ceiling Canopy to the

Ceiling Canopy

ceiling

Remove mounting balls from the Crossbar Assembly (A). Fit the

(D) Crossbar Assembly (A) and secure with

mounting balls. Note: The (D) should be snug

against the and the mounting balls. If not, adjust the length

STEP 1 - Install Ceiling Canopy, Rods and

Fixture Body together

A. Determine the Rods (B/C) to be

assembled to the Fixture Body (E)

according to your hanging height.

B. Pass the supply wires and ground wire

through the chosen rods (B/C) and the

Ceiling Canopy (D). Thread the Fixture

Body (E), the chosen Rods (B/C) and the

Ceiling Canopy (D) together. Hand

tighten until snug.

Suggested rods for Ceiling height:

9’ ceiling: use (1) 12” rod

10’ ceiling: use (2) 12” rods

Mounting

Screw

Hex Nut and

Lock Washer

Mounting Ball

Figure 3

Figure 1

of the nipple on the Crossbar

Assembly (A) by unscrewing

the preassembled hex nut

and lock washer and then

screwing the mounting

screws in or out of the

crossbar until the correct

length is achieved. Once the

Ceiling Canopy (D) is secure,

remove the mounting ball

and Ceiling Canopy (D) and

proceed to Step 4.

STEP 4 - Attach the Lanyard

A. The purpose of the lanyard is to

provide a means to support the fixture

hands free from the junction box while

connecting the electrical wires.

B.TurntheButtonStopsoitmaybe

inserted into a Crossbar slot. Make

sure the Button Stop is completely

inside the Crossbar. Slowly release

the fixture to make sure it is

supported by the Button Stop.

Proceed to the wiring steps in the

next step. Once you are complete

with the wiring, the Lanyard will push

into the junction box when the fixture

is placed for final mounting.

Crossbar

Button Stop

Lanyard

Slot

Figure 4

Assembly Instruction Sheet

Thank you for purchasing a product.

Summary of content (2 pages)

PAGE 1
Assembly Instruction Sheet Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses. Light Source: (8) B10 Candelabra Base Bulbs 60W Maximum Estimated Assembly Time: 30-45 minutes Preparation: Identify and inspect all parts before beginning installation. Check package content list and diagrams below to be sure all parts are present. If any parts are missing or damaged, do not attempt to assemble, install, or operate the fixture.
PAGE 2
STEP 5 - Wire Connections FINISH: WESTERN BRONZE A. Wrap bare or green ground wire around green ground screw on the crossbar, no less than 2 inches from the end of the wire. Tighten the green ground screw. B. Use standard wire connectors (not included) to make all wire connections. Twist connectors until wires are tightly joined together. Wrap each connection with approved electrical tape and carefully stuff all the connected wires into the Outlet Box.