Installation & Assembly

ManualsBrandsWrought Studio ManualsCeiling LightsAaru 1 - Light Single Globe Pendant

PENDANT LAMP

Save these instructions

CARE INSTRUCTIONS:

• Turnlightoandallowbulbtocoolbeforecleaning.

• Carefullywipecleanwithasoft,dryclothorstaticduster.

• Alwaysavoidtheuseofharshchemicalsorabrasivecleanersastheymay

causedamagetothexture’snish

Page1of6Made in China

IMPORTANT SAFETY INSTRUCTIONS:

• CAUTION –TURN OFF THE MAIN POWER AT THE CIRCUIT BREAKER BEFORE

INSTALLING THE FIXTURE, IN ORDER TO PREVENT POSSIBLE SHOCK.

• CAUTION –If you feel you do not have enough electrical wiring experience contact a

qualiedlicensedelectricianforinstallationofyourlightingxture.

• Theseinstructionsareprovidedforyoursafety.Pleasereadcarefullyandcompletely

beforebeginningtheassemblyandinstallationofthislightingxture.

• Donotusetheelectriccordonly(withoutsteel/reinforcedcable)tosupporttheweightofthe

lightingxture.

• Thislightingxtureisintendedforindooruseonly,andindrylocations.

• Thislightingxtureisintendedforceilingmountonly,andconnectedonlyto3-wire,

single-phaseelectricalsupplysystemwithproperGroundwireorsystem.

• Toavoidtheriskofre,donotexceedthemaximumwattageof60WTYPEAlamp,

or13WSelf-Ballastedlamp,or9WSBLEDlamporlampadapter.

(LEDbulbincluded)

WARNINGS:

• Toreducetheriskofre,electricalshock,orpersonalinjury:alwaysturnothislighting

xtureandallowittocoolbeforeattemptingtoreplacethelightbulb.

• Donottouchlightbulbwhilextureisturnedon.

• Keepammablematerialsawayfromthislightingxture.

• Neverlookdirectlyatalitbulb.

Removethextureandthemountingpackagefromthebox

andmakesurethatnopartsaremissingbyreferencingthe

illustrationsontheinstallationinstructions.

Summary of content (6 pages)

PAGE 1
PENDANT LAMP Remove the fixture and the mounting package from the box and make sure that no parts are missing by referencing the illustrations on the installation instructions. Save these instructions IMPORTANT SAFETY INSTRUCTIONS: • CAUTION – TURN OFF THE MAIN POWER AT THE CIRCUIT BREAKER BEFORE INSTALLING THE FIXTURE, IN ORDER TO PREVENT POSSIBLE SHOCK.
PAGE 2
Do not discard any contents until after assembly is complete to avoid accidentally discarding small parts or hardware. 1. F eed wires through the mounting plate (A). 4. Determine the desired length of the lamp cord, and secure length using small screw and screwdriver. 2. Securely connect wires as shown using wire connectors. 3. Secure mounting plate to the ceiling using screws. A 5. Carefully install the included A19 120V 2200K 4W LED light bulb. ! 1/2 Inch (12.7 WHITE WHITE 1/2 Inch (12.
PAGE 3
LAMPE SUSPENSION Sortir le luminaire et le nécessaire de fixation de l’emballage et consulter les illustrations dans les instructions d’installation pour vérifier qu’il ne manque aucune pièce. Conservez ces instructions CONSIGNES DE SÉCURITÉ ESSENTIELLES : • ATTENTION – SECTIONNER L’ALIMENTATION AU NIVEAU DU DISJONCTEUR AVANT D’INSTALLER LE LUMINAIRE, AFIN D’ÉCARTER LE RISQUE DE CHOC ÉLECTRIQUE.
PAGE 4
Ne mettez aucun élément de contenu au rebut avant de terminer l’assemblage au complet, afin d’éviter de jeter accidentellement de petites pièces ou un élément de quincaillerie. 1. Tirer les conducteurs à travers la plaque de fixation (A). 4. Déterminer la longueur souhaitée pour le cordon de la lampe et le bloquer en serrant la petite vis avec un tournevis. 2. R accorder solidement les conducteurs comme sur l’illustration ci-dessus à l’aide de capuchons de connexion. 3.
PAGE 5
LÁMPARA COLGANTE Extraiga el artefacto y el paquete de montaje de la caja y asegúrese de que no falten piezas verificando con las ilustraciones de las instrucciones de montaje. Guarde estas instrucciones INSTRUCCIONES IMPORTANTES DE SEGURIDAD: • PRECAUCIÓN - ANTES DE INSTALAR EL ARTEFACTO CORTE LA ALIMENTACIÓN ELÉCTRICA PRINCIPAL EN EL DISYUNTOR PARA EVITAR POSIBLES DESCARGAS ELÉCTRICAS.
PAGE 6
No deseche nada hasta después de haber terminado de ensamblar para evitar botar por accidente piezas pequeñas o herramientas. 4. Determine el largo deseado del cable de la lámpara y asegúrelo con un pequeño tornillo y un destornillador. 1. Pase los cables a través de la placa de montaje (A). 2. C onecte los cables en forma segura con conectores para cable, tal como se muestra arriba. 3. Asegure esta al cielorraso con tornillos. A 5. Instale con cuidado la bombilla LED A19 2200K 4W incluida.