SAFETY AND OPERATING MANUAL Original instructions Palm sander WX646 WX646.
General Power Tool Safety Warnings WARNING: Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference. The term “power tool” in the warnings refers to your electric (corded) power tool or batteryoperated (cordless) power tool. 1. Work area safety a) Keep work area clean and well lit. Cluttered or dark areas invite accidents.
4. Power tool use and care a) Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed. b) Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired.
for damage or install an undamaged accessory. After inspecting and installing an accessory, position yourself and bystanders away from the plane of the rotating accessory and run the power tool at maximum no-load speed for one minute. Damaged accessories will normally break apart during this test time. h) Wear personal protective equipment. Depending on application, use face shield, safety goggles or safety glasses.
b) Never place your hand near the rotating accessory. Accessory may kickback over your hand. c) Do not position your body in the area where power tool will move if kickback occurs. Kickback will propel the tool in direction opposite to the wheel’s movement at the point of snagging. d) Use special care when working corners, sharp edges etc. Avoid bouncing and snagging the accessory. Corners, sharp edges or bouncing have a tendency to snag the rotating accessory and cause loss of control or kickback.
2 1 3 4 5 6 1. On-off switch 2. Soft grip handle 3. Dust extraction adaptor 4. Sanding plate 5. Sanding paper* (See Fig. A) 6. Finger pad *Not all the accessories illustrated or described are included in standard delivery. Palm sander WX646 WX646.
TECHNICAL DATA Type WX646 WX646.1 (645-649-designation of machinery, representative of palm sander) Voltage 220-240V~50/60Hz Power input 160W Rated no load speed 12000/min Base size 140x140x95mm Protection class /ll Net weight 0.9kg NOISE AND VIBRATION DATA A weighted sound pressure LpA= 80.8dB(A) 3dB(A) KpA A weighted sound power LwA= 91.
is switched off and when it is running idle but not actually doing the job. This may significantly reduce the exposure level over the total working period. Helping to minimise your vibration exposure risk. ALWAYS use sharp chisels, drills and blades. Maintain this tool in accordance with these instructions and keep well lubricated (where appropriate). If the tool is to be used regularly then invest in anti vibration accessories. Avoid using tools in temperatures of 100C or less.
OPERATING INSTRUCTIONS NOTE: Before using the tool, read the instruction book carefully. Intended Use The machine is intended for dry sanding of wood, plastic, filler and coated surfaces. 1. FITTING THE SANDING PAPER (See Fig. A) Fit the paper over the pad so that it covers the entire area. Make sure the sanding paper is even with the edges and that the dust collection holes in the pad and sanding paper is aligned and the sanding paper evenly overlaps the pad. Never use your sander without a sanding paper.
triangular base. 2) Replace triangular base by fastening the detail sanding attachment to base position. 3) Fix it by 5 screws. 4) Similar process is conducted when detail sanding attachment is changed to triangular base. E F Palm sander 7. ATTACH SANDING SHEETS AND PADS (See Fig. E) This sander features an easy hook and loop accessory fastening system for quick changing without clamps. 1) Unplug the sander. 2) Carefully center the sanding sheet (A) or pad over the base (3/4) to be used.
WORK HINTS FOR YOUR PALM SANDER ENVIRONMENTAL PROTECTION If your power tool becomes too hot, run no load for 2-3 minutes to cool the motor. Always ensure the work-piece is firmly held or clamped to prevent movement. Any movement of the material may affect the quality of the sanding finish. Start your sander before sanding and turn off only after stopping sanding. For best results sand wood in the direction of the grit. Do not start sanding without sandpaper fitted.
Plug replacement (UK & Ireland only) DECLARATION OF CONFORMITY If you need to replace the fitted plug then follow the instructions below. IMPORTANT The wires in the mains lead are colored in accordance with the following code: BLUE=NEUTRAL BROWN=LIVE As the colors of the wires in the mains lead of this appliance may not correspond with the colored markings identifying the terminals in your plug, proceed as follows. The wire which is colored blue must be connected to the terminal which is marked with N.
www.worx.com Copyright © 2013, Positec. All Rights Reserved.
