Operation Manual
Cordless Circular Saw EN
13
Sawdust Removal See Fig. H
EXACTRACK
TM
What is EXACTRACK
TM
?
EXACTRACK
TM
is an innovative function, which can
help to make a straight cut easier by keeping the
blade flush against the cutting guide board.
Safety notes
WARNING: Blade is sharp. Always wear
protective gloves.
Keep your hands off from the lower blade
guard after opening the lower blade guard.
EXACTRACK
TM
operation scope
1. EXACTRACK
TM
operates between 0~43mm in
depth. (See Fig. I)
2. EXACTRACK
TM
works only with 90 degree cut, it
does not work with any angle of bevel cut.
Before operation
WARNING: Make sure battery is not
installed prior to making any adjustments
to the saw, and please place the battery pack
nearby the saw.
1. Adjust the desired cutting depth (range 0~43mm).
(See Fig. I)
2. Turn the lever to EXACTRACK
TM
mode. (See Fig.
J)
3. Mark the desired cut line on the workpiece, then
clamp the cutting guide board (not supplied) to
make the board edge right on the cut line, the
length of the cutting guide board should leave
230mm longer at the both ends. (See Fig. K1)
4. Place the EXACTRACK
TM
sub-base plate (red part)
on the top of cutting guide board (not supplied),
and ensure the main-base plate is sitting on the
workpiece. (See Fig. K2)
5. Open the lower blade guard manually (
keep
your hands off the blade), push the saw
against the side of the cutting guide board, then
release the hand off the lower blade guard. (See
Fig. K3)
Operation
1. Install the battery.
2. Please hold the saw firmly with both hands and
make sure the main base plate fits securely
against the cutting guide board (not supplied)
during cutting. (See Fig. K4)
3. Switch on the tool to start cutting (See Fig. K5)
STANDARD Mode
For regular 90 degree or bevel cutting (disable
EXACTRACK
TM
fucntion), turn the lever to STANDARD
mode and then your tool can be used as a standard
circular saw. (See Fig. L)
The STANDARD mode can be used in the cutting
depth of 0~55mm (90 degree), 0~39mm (45 degree).
For product information, go to www.worx.com
and see How To video.
WORKING TIPS FOR YOUR
TOOL
If your power tool becomes too hot, please run your
circular saw no load for 2-3 minutes to cool the
motor. Avoid prolonged usage at very low speeds.
Protect saw blades against impact and shock. Do not
force the tool. Apply light and continuous pressure
in order to avoid overheating the blade tips. Cutting
with extreme force can significantly reduces the
performance capability of the tool and reduces the
service life of the saw blade. Sawing performance
and cutting quality depend essentially on the
condition and the tooth count of the saw blade.
Therefore, use only sharp saw blades that are suited
for the material being cut.
Choice of blades: 24 teeth for general work, approx.
40 teeth for finer cuts, more than 40 teeth for very
fine cuts into delicate surfaces, cement board, etc.
Only use saw blades recommended.
MAINTAIN TOOLS WITH
CARE
Remove the battery before carrying out any
adjustment, servicing or maintenance.
Keep tools sharp and clean for better and safer
performance. Follow instructions for lubricating and
changing accessories. Your power tool requires no
additional lubrication or maintenance. There are no
user serviceable parts in your power tool. Never use
water or chemical cleaners to clean your power tool.
Wipe clean with a dry cloth. Always store your power
tool in a dry place. Keep the motor ventilation slots
clean. Keep all working controls free of dust.
Periodically clear dust and chips from guard and base
to ensure proper performance.
The ambient temperature range for tool and battery
use and storage is 0
O
C-45
O
C.
The recommended ambient temperature range for
the charging system during charging is 0
O
C-40
O
C.
ENVIRONMENTAL
PROTECTION
Waste electrical products must not be
disposed of with household waste. Please
recycle where facilities exist. Check with your
local authorities or retailer for recycling
advice.