SAFETY AND OPERATING MANUAL ORIGINAL INSTRUCTIONS CORDLESS HAMMER DRILL WU362 WU370 WU370.
General power tool safety warnings c) Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock. d) Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of electric shock. e) When operating a power tool outdoors, use an extension cord suitable for outdoor use.
the power tool may result in personal injury. e) Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations. f) Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves away from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts. g) If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used.
Drill Safety Warnings g) Keep battery pack clean and dry. h) Wipe the battery pack terminals with a clean dry cloth if they become dirty. 1 Wear ear protectors when impact drilling. Exposure to noise can cause hearing loss. 2 Use auxiliary handle(s), if supplied with the tool. Loss of control can cause personal injury. 3 Hold power tool by insulated gripping surfaces, when performing an operation where the cutting accessory may contact hidden wiring.
Symbols t) Do not use any battery pack which is not designed for use with the equipment. u) Keep battery pack out of the reach of children. v) After extended periods of storage, it may be necessary to charge and discharge the battery pack several times to obtain maximum performance. w) Retain the original product literature for future reference. x) Remove the battery from the equipment when not in use. y) Dispose of properly.
Component list 1 2 3 4 5 11 1 2 3 4 5 6 7 8 9 10 11 Keyless Chuck Torque Adjustment Ring Two-Speed Gear Control Forward/Reverse Rotation Control On/Off Switch Soft Grip Handle Battery Pack Release Button Battery Pack * Double Ended Bit Auxiliary Handle * Sight Light 6 10 9 7 8 * Not all the accessories illustrated or described are included in standard delivery.
Technical data Vibration information Type WU362 WU370 WU370.9(360-379-designation of • Vibration total values (triax vector sum) determined according to EN 60745: machinery, representative of Battery-powered Drill) Model No. WU362 • Voltage 14.4V • No load speed • Impact rate • Number of clutch positions • Max torque • Chuck capacity WU370 WU370.9 18V 0-400/0-1600/min 0-450/0-1650 /min 0-6400/ 0-25600bpm 0-7200/ 0-26400bpm 50N.m 60N.
Accessories Helping to minimize your vibration exposure risk. ALWAYS use sharp chisels, drills and blades. Maintain this tool in accordance with these instructions and keep well lubricated (where appropriate). If the tool is to be used regularly then invest in anti vibration accessories. Avoid using tools in temperatures of 100C or less. Plan your work schedule to spread any high vibration tool use across a number of days. WU362 WU370 WU370.9 2.
Operating instructions Note: Before using the tool, read the instruction book carefully. Intended Use The machine is intended for driving in and loosening screws as well as for drilling in wood, metal, ceramic and plastic. BEFORE PUTTING INTO OPERATION A) CHARGING THE BATTERY The battery charger supplied is matched to the Li-ion battery installed in the machine. Do not use another battery charger. The Li-ion battery is protected against deep discharging.
Operation 1 AUXILIARY HANDLE (See Fig.B) Slide the handle onto the drill and rotate it to the desired working position. To clamp the auxiliary handle, rotates the handgrip clockwise. To loosen it, rotate the handgrip anti-clockwise. Always use the handle during operation. 2 ON/OFF SWITCH (See Fig.C) C Depress the On/Off switch to start and release it to stop your drill. The on/off switch is fitted with a brake function which stops your chuck immediately when you quickly release the switch.
5 TWO-SPEED GEAR CONTROL (See Fig.D) The drill has a two-speed gear control designed for drilling or driving at LOW (mark is 1) or HIGH (mark is 2) speeds. A slide switch is located on top of the drill to select either LOW or HIGH speed. When using the drill in the LOW speed range, the speed will decrease and the drill will have greater power and torque. When using the drill in the HIGH speed range, the speed will increase and the drill will have less power and torque.
a lower setting. When drilling in masonry and concrete choose the hammer position . When drilling in wood, metal, plastic and screwdriver choose the drill position .
Problem solution 10 DRILLING When drilling into a hard smooth surface, use a center punch to mark the desired hole location. This will prevent the drill bit from slipping off center as the hole is started. Hold the tool firmly and place the tip of the bit at the point to be drilled. Depress the switch trigger to start the tool. Move the drill bit into the workpiece, applying only enough pressure to keep the bit cutting. Do not force or apply side pressure to elongate a hole.
Maintenance Disposal of an exhausted battery pack Remove the battery pack from the tool before carrying out any adjustment, servicing or maintenance. Your power tool requires no additional lubrication or maintenance. There are no user serviceable parts in your power tool. Never use water or chemical cleaners to clean your power tool. Wipe clean with a dry cloth. Always store your power tool in a dry place. Keep the motor ventilation slots clean. Keep all working controls free of dust.
DECLARATION OF CONFORMITY We, Positec Power Tools (Europe) Ltd, PO Box 152, Leeds, LS10 9DS, UK Declare that the product, Description WORX Cordless hammer drill Type WU362 WU370 WU370.
Copyright © 2013, Positec. All Rights Reserved.
