SAFETY AND OPERATING MANUAL ORIGINAL INSTRUCTIONS 3 IN 1 DRILL/DRIVER/IMPACT DRIVER WU288
General power tool safety warnings entering a power tool will increase the risk of electric shock. d) Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of electric shock. e) When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock.
e) Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations. f) Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves away from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts. g) If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 Additional safety rules for your cordless impact driver hidden wiring. Fasteners contacting a “live” wire may make exposed metal parts of the power tool “live” and could give the operator an electric shock. Remove the battery pack from the impact wrench before carrying out adjustments. Do not expose to rain or water. Do not store the battery pack in temperatures over 40oC. Always charge the battery pack between temperatures 0oC to 30oC.
Symbols To reduce the risk of injury, user must read instruction manual Warning Wear ear protection Wear eye protection Wear dust mask Indoor use only Do not expose to rain or water Do not burn Do not dispose of batteries.
Component list 1 Forward, reverse rotation and lock control 2 Soft grip handle 7 8 9 3 Battery pack * 4 Battery pack latch 5 On/off switch with variable speed control 6 LED light 7 Collet locking sleeve 8 Torque adjustment ring 9 Function mode selection switch 6 1 5 2 4 3 *Not all the accessories illustrated or described are included in standard delivery.
Technical data • Voltage • No load speed • Impact rate • Max torque • Torque setting • Drilling capacity • • • Chuck type Charging time Machine weight Screwdriver mode Drill mode (Lo-Hi) Impact driver mode Impact driver mode Drill mode Wood Steel Vibration information • 12 V 0-600/min 0-600/ 0-2200/min 0-2200/min 0-3000/min 100N.m 15N.m 22 20mm 8mm 6.35mm (1/4”) hex 30min 1.
Helping to minimize your vibration exposure risk. ALWAYS use sharp chisels, drills and blades. Maintain this tool in accordance with these instructions and keep well lubricated (where appropriate). If the tool is to be used regularly then invest in anti vibration accessories. Avoid using tools in temperatures of 100C or less. Plan your work schedule to spread any high vibration tool use across a number of days. Accessories • • • • • • 1.
Operating instructions Note: Before using the tool, read the instruction book carefully. Intended use The machine is intended for fastening and loosening of bolts, nuts and various threaded fasteners as well as for drilling in wood, metal and plastic. 8 BEFORE PUTTING INTO OPERATION A) BATTERY CHARGING The battery charger supplied is matched to the Li-ion battery installed in the machine. Do not use another battery charger. The Li-ion battery is protected against deep discharging.
1 A D1 B D2 C D3 OPERATION INSTALLING OR REMOVING A BIT HOLDER, SOCKET OR SCREWDRIVER BIT (See B) To install the desired bit, pull the collet locking sleeve (7) forward and insert the desired bit into the sleeve as far as it will go. Then release the collet locking sleeve to secure the bit. To remove the bit, pull the collet locking sleeve (7) forward and take the tool out firmly. 2 ON / OFF SWITCH (See C) Depress the On/Off switch (5) to start and release it to stop your tool.
chuck is rotating, wait until it has stopped! 5 USING THE LED LIGHT To turn on the light simply press the on/off switch. When you release the on/off switch, the light will be off. LED lighting increases visibility-great for dark or enclosed area. LED is also a battery capacity indicator. It will flash when power gets low. 8 6 FUNCTION MODE SELECTION A The operation of the tool for each application is set with the function mode selection switch (9).
set on a lower setting. Make the setting as follows: 1-4 5-9 10 - 14 15 - 19 20 - 22 for driving small screws for driving screws into soft material for driving screws into soft and hard material for driving screws into hard wood for driving larger screws 8 DRILLING OPERATION A D1 Slide the function mode selection switch (9) to mark “ ”or “ ”. The adjusting ring can be aligned in any torque levels for this operation.
drill bits in good condition. Always use a magnetic bit holder (not included) when using short screwdriver bits. When screwdriving, apply a small quantity of liquid soap or similar to the screw threads to ease insertion. range again. 10 PROTECTION AGAINST DEEP DISCHARGING The Li-ion battery is protected against deep discharging by the “Discharging Protection System”. When the battery is empty, the machine is switched off by means of a protective circuit: The inserted tool no longer rotates.
Plug replacement (UK & Ireland only) If you need to replace the fitted plug then follow the instructions below. IMPORTANT The wires in the mains lead are colored in accordance with the following code: BLUE =NEUTRAL BROWN = LIVE As the colors of the wires in the mains lead of this appliance may not correspond with the colored markings identifying the terminals in your plug, proceed as follows. The wire which is colored blue must be connected to the terminal which is marked with N.
EC Declaration of conformity We, Positec Power Tools (Europe) Ltd,PO Box 152, Leeds, LS10 9DS, UK Declare that the product, Description WORX 3 in 1 drill/driver/impact driver Type WU288 Function Drilling, tightening and loosening screws, nuts with a rotary impact mechanism Complies with the following Directives, • EC Machinery Directive 2006/42/EC • EC Electromagnetic Compatibility Directive 2004/108/EC Standards conform to EN 55014-1 EN 55014-2 EN 60745-1 EN 60745-2-1 EN 60745-2-2 The person authorized to
Copyright © 2011, Positec. All Rights Reserved.
