SAFETY AND OPERATING MANUAL ORIGINAL INSTRUCTIONS CORDLESS DRILL WU127 WU127.
General power tool safety warnings entering a power tool will increase the risk of electric shock. d) Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of electric shock. e) When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock.
e) Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations. f) Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves away from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts. g) If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used.
Additional safety rules for your Cordless drill 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 Hold power tool by insulated gripping surfaces, when performing an operation where the cutting accessory may contact hidden wiring. Cutting accessory contacting a “live” wire may make exposed metal parts of the power tool “live” and could give the operator an electric shock. Remove the battery pack from the drill before carrying out adjustments. Do not expose to rain or water.
Symbols To reduce the risk of injury, user must read instruction manual Warning Wear ear protection Wear eye protection Wear dust mask Indoor use only Do not expose to rain or water Do not burn Do not dispose of batteries.
Component list 1 Keyless chuck 2 Torque adjustment ring 1 3 Two-speed gear control 2 3 4 Forward/Reverse rotation control 5 Soft grip handle 6 Battery pack release button 7 Battery pack * 8 On/off switch 9 LED light 9 4 8 5 6 7 * Not all the accessories illustrated or described are included in standard delivery.
Technical data Vibration information WU127 WU127.9 • Voltage • No load speed • Number of clutch positions • Max torque(soft/hard) • Chuck capacity • Max. drilling capacity • Charging time 30min • Machine weight 1.0kg Vibration total values (triax vector sum) determined according to EN 60745: • Drilling into metal 12V 0-350 / 0-1300/min 15+1 Steel 10mm 20mm A weighted sound pressure A weighted sound power KpA & K wA Wear ear protection when sound pressure is over K = 1.
significantly reduce the exposure level over the total working period. Helping to minimize your vibration exposure risk. ALWAYS use sharp chisels, drills and blades. Maintain this tool in accordance with these instructions and keep well lubricated (where appropriate). If the tool is to be used regularly then invest in anti vibration accessories. Avoid using tools in temperatures of 100C or less. Plan your work schedule to spread any high vibration tool use across a number of days. Accessories WU127 WU127.
Operating instructions Note: Before using the tool, read the instruction book carefully. Intended use The machine is intended for driving in and loosening screws as well as for drilling in wood, metal and plastic. BEFORE PUTTING INTO OPERATION • CHARGING THE BATTERY The battery charger supplied is matched to the Li-ion battery installed in the machine. Do not use another battery charger. The Li-ion battery is protected against deep discharging.
A B C D E F The on/off switch is fitted with a brake function which stops your chuck immediately when you quickly release the switch. It is also a variable speed switch that delivers higher speed and torque with increased trigger pressure. Speed is controlled by the amount of switch trigger depression. Warning: Do not operate for long periods at low speed because excess heat will be produced internally. 2 SWITCH LOCK The switch trigger can be locked in the OFF position.
A B C D D E F Gear I Low speed range: for screwdriving or working with large drilling diameter. Gear II High speed range: for working with small drilling diameter. Warning: To prevent gear damage, always allow the chuck to come to a complete stop before changing the direction of rotation or the two-speed gear control. 5 CHUCK ADJUSTMENT (See D) C To open the chuck jaws rotate the front section of the chuck.
C D 7 AUTOMATIC SPINDLE LOCK (See F) The automatic spindle lock allows you to use it as a regular screwdriver. You can give an extra twist to firmly tighten a screw, loosen a very tight screw or continue working when the battery energy has expired. For manual screwdriver purposes, the chuck is automatically locked when the tool is off. 8 USING THE LED LIGHT To turn on the light simply press the on/off switch. When you release E the on/off switch, the light will be off.
Problem solution 10 DISPOSAL OF AN EXHAUSTED BATTERY PACK To preserve natural resources, please recycle or dispose of the battery pack properly. This battery pack contains Lithium batteries. Consult your local waste authority for information regarding available recycling and/or disposal options.
Maintenance Plug replacement (UK & Ireland only) Your tool requires no additional lubrication or maintenance. There are no user serviceable parts in your power tool. Never use water or chemical cleaners to clean your power tool. Wipe clean with a dry cloth. Always store your power tool in a dry place. Keep the motor ventilation slots clean. Keep all working controls free of dust. Occasionally you may see sparks through the ventilation slots. This is normal and will not damage your power tool.
EC Declaration of conformity We, Positec Power Tools (Europe) Ltd, PO Box 152, Leeds, LS10 9DS, UK Declare that the product, Description WORX Cordless drill Type WU127 WU127.
Copyright © 2011, Positec. All Rights Reserved.
