Use and Care Manual

2 in 1 Cordless Lawn Mower EN
16
No light is
illuminated.
At least one battery is not fully
installed or battery may be
defective.
Only one light is
flashing twice per
cycle.
At least one battery is over
discharged (please refer to
the battery charge condition),
please recharge the two bat-
teries at once before use again
or storage.
Only one light
is flashing three
times per cycle.
At least one battery is hot,
wait for them cool down
before start again.
Only one light is
flashing four times
per cycle.
The machine is over load.
Raise the cutting height or
push slowly.
MULCHING MOWING TIPS
When using the mulching plug, your new mower
is designed to cut the grass clippings into small
pieces and distribute them back into the lawn, using
mulching fins located inside the mower deck.
Under normal conditions, the mulched grass will
biodegrade quickly to provide nutrients to the lawn.
Please review the following recommendations for
optimum mulching performance,
1) Avoid mowing when the grass is wet from rain or
dew. Wet grass may form clumps which interfere
with the mulching action and reduce runtime. The
best time to mow grass is in the late afternoon
when the grass is dry and the newly cut area will
not be exposed to direct sunlight.
2) For best mulching performance, set the cutting
height to remove about one third of the grass
blade length. If the lawn is overgrown, it may be
necessary to increase the cut height to reduce the
pushing effort and prevent overloading the motor.
For extremely heavy mulching, it is advisable
to first cut at a high cut height setting, and then
re-cut to the final cut height. Otherwise, make
narrower cuts and mow slowly.
3) For best performance, keep the mower housing
free of built-up grass. From time to time turn
off mower and wait for the blade to come to a
complete stop. Then unplug the Safety Key and
turn mower on its side. Using an object such as
a stick, wipe out any accumulation of grass in the
blade area. Be careful of the sharp edges of the
blade. Clean often in wet, new grass, and always
after every use.
4) Certain types of grass or grass conditions may
require that an area be mulched a second time
to fully disperse the grass throughout the lawn.
If cutting a second time, it is advisable to cut
perpendicular (across) the first cut pattern. DO
NOT CHANGE CUT PATTERN IN ANY WAY THAT
WOULD CAUSE MOWING DOWN A HILL.
5) Change your cutting pattern from week to week.
This will help prevent matting and graining of the
lawn.
CUTTING AREA
The cutting area can be affected by many factors
including: cutting height, operation practices (ex:
starting/stopping), lawn moisture levels, grass length
and thickness.
The below table provides the potential cutting area
based on the specific cutting condition.
Cutting Height
Recommend lot size
(maximum)
Cutting off .75”
(2cm)
With 2*20V/4.0Ah batteries
Up to 5500 sq.ft. (500m
2
) *
* Used with two fully charged battery packs.
TIPS:
1) Mowing the lawn frequently and reducing the
amount of starting/stopping procedures will help
conserve battery runtime. It is recommended
to always use the same two batteries during
operation with fully charged levels.
2) For the best cutting performance, it is
recommended to only mow up to 1/3 or less
of the current grass height at a time. Mow at
a slower pace when cutting long/thick grass
to allow the mower to properly discharge the
clippings.
MAINTENANCE
WARNING: Stop the mower and remove
the safety key before removing the
grass bag.
NOTE: To ensure long and reliable service, perform
the following maintenance procedures regularly.
Check for obvious defects such as a loose, dislodged
or a damaged blade, loose fittings, and worn or
damaged components. Check that the covers and
guards are all undamaged and are correctly attached
to mower. Carry out any necessary maintenance or
repairs before operating mower. If the mower should
happen to fail despite regular maintenance, please
call our customer helpline for advice.
BLADE SHARPENING
KEEP BLADE SHARP FOR BEST MOWER
PERFORMANCE.
WEAR PROPER EYE PROTECTION WHILE
REMOVING, SHARPENING, AND INSTALLING
BLADE. ENSURE THAT SAFETY KEY IS REMOVED.
Sharpening the blade twice during a mowing season