WG701E WG701E-M-060818.
WG701E-M-060818.
� � � � � � � � � �� �� � A WG701E-M-060818.
�� �� �� �� D E F �� �� �� �� G H H.1 �� �� H.2 I J K L M N WG701E-M-060818.
1. SWITCH LEVER 2. UPPER HANDLE 3. SAFETY BUTTON 4. CABLE CLIPS 5. LOWER HANDLE 6. GRASSBOX HANDLE 7. GRASSBOX RELEASE BUTTON 8. GRASSBOX 9. DECK 10. PIVOT PIN (See C) 11. UPPER HANDLE KNOB (See E) 12. UPPER HANDLE KNOB WASHER (See E) 13. UPPER HANDLE KNOB JOINT (See E) 14. SPANNER (See I) 15. BLADE BOLT (See H) 16. BLADE (See H) 17. BLADE SPACER (See H) 18. FAN (See H) 19. ROLLER 20. INSPECT WINDOW (See J) 21. COVER (See E) Hover Mower WG701E-M-060818.
TECHNICAL DATA Rated Voltages: Rated Power: Rated No-load Speed: Cutting diameter: Cut height: Cut depth adjustment : 230V~50Hz 1600W 4500min-1 38cm 12-33mm 4 Grass collection capacity: 38L Moisture resistance Class: IPX4 Machine Weight: 15.3Kg NOISE AND TECHNICAL DATA A weighted sound pressure 83dB(A) A weighted sound power 96dB(A) Wear ear protection when sound pressure is over 85dB(A) Typical weighted vibration 5.
SAFETY INSTRUCTIONS WARNING! Read all instructions Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury. SAVE THE INSTRUCTION FOR FUTURE USE If not used properly this lawnmower can be dangerous! This lawnmower can cause serious injury to the operator and others, the warning and safety instruction must be followed to ensure reasonable safety and efficiency in using this lawnmower.
3. Replace worn or damaged parts for safety. 4. Do not try to repair the machine or access internal parts. Use authorized service centers only. 5. Only use the replacement blade, blade bolt, spacer and impeller specified for this product. 6. Be careful during adjustment of the lawnmower to prevent entrapment of the fingers between moving blades and fixed parts of the machine. 7. If an extension cord is used make sure it is for outdoor use and marked as such.
ASSEMBLY IMPORTANT! Before you assemble the hover mower, check the accessories according above information, make sure the accessories are completed. FITTING THE LOWER HANDLE. Note: The cable can move through the cover(21), adjust it to help you fit the lower handle easily. 1. Remove the grassbox (8) from the deck (See A). This can help you to assemble the lower handle (5) on deck (9) easily. 2. Insert the lower handle into the handle slot of the deck (See B).
the blade . Tighten down and please check that the blade is firmly secured. 7. To store the spanner insert it into the rear of the switchbox (See I). Do not put it in grass. Warning! Spacers must only be fitted between the blade and the fan and NEVER between the blade and the bolt. HOW TO MOW NOTE: • Cut grass when it is dry. • Keep the mower blade sharp and balanced. • Do not set the cutting height too low, especially at the beginning of the mowing season.
condition. If the blade is cracked or damaged replace it with a new one. Storage: Rotate the Upper Handle knob to release the upper and lower handle Clean the exterior of the machine thoroughly using a soft brush and cloth. Do not use water, solvents or polishes. Remove all grass and debris, especially from the ventilation slots. Turn the machine on its side and clean the blade area. If grass cuttings are compacted in the blade area, remove with a wooden or plastic implement.
DECLARATION OF CONFORMITY We, POSITEC Power Tools (Suzhou) Co., Ltd. No. 11 Yangqing Road, Loufeng Area, Suzhou Industrial Park, Jiangsu 215021, P. R. China Declare that the product, Description WORX Hover Type WG701E Complies with the essential health and safety requirements of the following directives: - EMC Directive. 89/336 EEC. - Low Voltage Directive. 73/23 EEC. - CE Marking Directive 93/68 EEC. - Machinery Directive 98/37 EC - Noise emission in the environment by equipment for use outdoors Directive.
WG701E-M-060818.
WG701E-M-060818.
WG701E-M-060818.
WG701E-M-060818.
