User's Manual

4
Partitions
changing for voice messages...............7-2
for voice messages ..............................7-2
Password ..................................................2-3
Performance Issues...................................4-3
Pin-outs ...................................................A-1
Zebra Cameo Printer ...........................A-1
Planning for expansion.............................5-1
Planning for hardware failures .................5-2
Planning for system failures.....................5-1
Playing back a recorded voice message ...7-3
Plessey code ............................................. I-1
Poor lighting situations
suggestions for dealing with................7-1
poor read rates when scanning bar codes.8-5
Portable Printer Pin-outs
Zebra Cameo.......................................A-1
Portable Printers
Zebra Cameo Printer .........................6-12
portable printing.....................................6-13
Postamble...............................................2-15
using to check data length in NON
PORTABLE mode .......................2-16
Postambles - selective trimming ............2-16
Power-up
6 beeps from terminal..........................8-5
Preamble.................................................2-14
selective trimming.............................2-15
using to check data length.................... 2-15
Prefix for bar code types ........................2-11
Printer
setting Parity to match serial printer..........2-20
Problems reading Bar Codes....................8-5
Programming for the RF Terminal...........6-1
Programming Voice Messages.................7-2
Protocol setting for serial printer............2-20
PSC Long Range Laser Scanner ............. L-2
Q
quiet zone .................................................8-6
R
R/F Serial Pin-outs ..................................A-1
R/F Terminal Firmware Upgrades .......... B-1
R/F Terminal Menu Functions
SETUP MODE....................................1-4
DEVICE SIGN ON.............................1-4
FIRMWARE UPDATE.......................1-4
Radio not Responding..............................8-4
Range problems........................................8-4
Reader doesn't beep when reading bar codes
.............................................................8-5
reading through a windshield ................... J-3
Reading through a windshield.................. J-3
reaing in sunlight - aiming dot ................. J-3
Re-assigning character codes .................2-16
rechargeable batteries.............................2-17
recharging battery procedure....................1-3
Recording a voice message using the
microphone......................................... 7-3
Recording and Playback of Voice Messages
............................................................ 7-3
Recording time alloted for voice
messages............................................. 7-2
Recovering from hardware failures......... 5-2
Recv Setup/Voice Please Wait................ 7-5
Reduced Space Symbology code........... 2-13
resending prompts after a sign-out .......... 5-2
Reset...................................................... 2-20
response time is poor............................... 8-4
Restrictions on bar code data length...... 2-14
restrictions on using arrow keys to transmit
special characters................................ 6-2
returns to 1st screen................................. 8-5
RF System
before you begin programming .......... 5-1
creating programs to prompt the terminal
....................................................... 6-1
operator errors .................................... 5-2
planning for expansion ....................... 5-1
planning for failures ........................... 5-1
planning for hardware failures............ 5-2
using Demo programs to test system.. 5-2
RF System Setup ..................................... 2-1
RF Terminal
opening screen.................................... 1-4
system components ...............................1-1
RF Terminal Cases and Holsters .............L-4
RF Terminal Default Settings.................. 2-1
RF Terminal Problems ............................ 8-5
RF Terminal setup
using keypad to setup ......................... 2-3
using the bar coded setup menu.......... 2-2
RF Terminal Setup .................................. 2-1
2 of 5 Code ....................................... 2-12
2 of 5 Length .................................... 2-13
Batteries............................................ 2-17
Baud Rate for serial printer .............. 2-20
Beep Tone......................................... 2-17
Characters......................................... 2-16
Code 3 of 9 ......................................... 2-9
Control Keys Only.............................. 2-6
Data Bits setting for serial printer .... 2-20
Date Format...................................... 2-17
Device IP Address.............................. 2-5
Display of Year ................................ 2-18
Encryption .......................................... 2-6
Encryption Key................................... 2-6
Laser Scanner Options...................... 2-19
LCD Backlight Display Mode............ 2-7
MSI/Plessey...................................... 2-13
Parity for serial printer...................... 2-20
Preamble........................................... 2-14
Protocol setting for serial printer...... 2-20
Reset................................................. 2-20
RSS-14 code..................................... 2-13
Server IP Address............................... 2-5