User's Manual

1
Index
1
1 second voice messages..........................7-2
1/2 second voice messages.......................7-2
2
2 of 5 Code.............................................2-12
default length setting.........................2-13
enabling check digit ..........................2-12
susceptible to mis-reads....................... 2-13
2 of 5 Codes
reading variable length bar codes......2-13
2 of 5 Length..........................................2-13
4
4 digit year option ..................................2-18
4 second laser beam ...............................2-19
6
6 beeps on power up................................8-5
A
Access Point Found – Mismatch on
SSID....................................................8-3
Access Point Found- Mismatch on
WKEY.................................................8-3
Accumulate Mode................................... C-4
numeric barpad table.......................... C-4
ActiveX programming .............................6-2
Advanced Features/Functions for
Code 39 .............................................. C-2
AIAG....................................................... C-1
aiming dot ................................................ J-2
aiming dot enabling.................................. J-3
ASCII Code Equivalent Table ............... M-1
Assigning Error Messages........................7-4
Automobile ID reading ............................ J-3
Automobile windshield reading ............... J-3
Avoiding substitutions in scanning............ 2-19
B
B11 Rubber Boot for Integrated Laser RF
Terminal............................................. L-4
Backlight Display.....................................2-7
Backlight Duration...................................2-7
Bar code data length checking ...............2-14
Bar Code ID's.........................................2-11
Bar Code Menu Only setup parameters ...2-1
bar code symbol .......................................2-4
Bar Code Type identification.................2-11
Bar Codes
Accumulate Mode.............................. C-4
character substitution ........................2-16
default settings ....................................2-2
ID character prefix ............................2-11
preambles and postambles.................2-11
trimming characters...........................2-15
using Postamble to add terminator
character .......................................2-15
Base Shut Down............................... 6-1, 8-3
Basic RF System communications...........3-1
Batteries..................................................2-17
battery charging........................................1-3
Battery Life indicator ...............................1-3
Battery Status indicator ..........................2-17
Baud Rate for serial printer ....................2-20
Beep Tone ..............................................2-17
Beeping
and Accumulate Mode........................C-4
changing the tone or pitch .................2-17
during setup configuration...................2-2
Beeping a lost unit....................................3-2
Before you begin programming ...............5-1
BEGIN key
transmitting ASCII 23 to host .............6-1
Blocking unauthorized listening..................2-6
bright light problems - aiming dot...........J-3
C
Cable pin-outs .........................................A-1
Cables needed for voice message cloning7-5
Cables for Zebra Cameo Printer ...............A-1
Cameo Printer.........................................6-12
Cameo Printer Pin-outs ............................A-1
Cannot Communicate with Pick
Processor .............................................8-4
Caps Lock ON
Code 39 setup parameter .....................2-9
CCD pin-outs...........................................A-1
Change Batteries ......................................8-3
CHANGE BATTERIES...........................1-3
Changing a prompt...................................3-2
Changing character output......................2-16
Changing more than one setup parameter at
a time using the bar coded setup
menu....................................................2-3
Changing the AA batteries on the RF
Terminal ..............................................1-3
Changing the default voice messages.......7-5
Changing the Device IP Address..............2-5
Changing the RF Terminals automatic shut-
off time..............................................2-19
Changing the Server IP Address ..............2-5
Changing the Starting Channel.................2-5
Changing the Subnet Mask............... 2-5, 2-6
Changing the voice message partitions ....7-2
Character codes - reassigning.................2-16
Characters...............................................2-16
charging batteries in RF Terminal............1-3
Check Character
Code 39 ..............................................C-2