User's Manual

7
RF Terminal Setup Parameters ................................. 2-5
RIGHT ARROW key
transmitting ASCII 31 to host ............................. 6-12
RMA's ....................................................................... 8-8
Routing the Wiring .................................................... B-2
RS-232 Cable Pin-outs .............................................. C-1
RS-232 Extension cables .......................................... C-1
RS232 problems........................................................... 8-6
RS-422 Termination Jumpers .................................. A-2
RSS-14 code ............................................................ 2-14
S
Scanner input only - breaking out of ........................ 6-3
scanning through a windshield .................................. L-3
SEARCH key
transmitting ASCII 11 to host ............................. 6-12
Security Code - setting on Terminal ......................... 2-6
Security Code for Base or Relay ................................. 2-23
Selective data trimming by bar code type ...... 2-16, 2-17
Sequence Error .......................................................... 8-3
Sequence Error Message ......................................... 6-10
Serial cables
"noise" problems ................................................... 4-4
serial device attachment ............................................ 6-3
serial input on Terminal ............................................ 6-3
Serial keyboard input ................................................ 6-3
Serial output command for terminal ......................... 6-4
Serial pin-outs ........................................................... C-1
Serial printer setup paramters on terminal .............. 2-21
Serial Reply - Base to host programming ................. 6-7
Set Date ................................................................... 2-19
Set Time .................................................................. 2-19
Setting serial parameters on your Base or Relay .... 2-23
Setting the Relay ID ................................................. A-2
Setup
RF Terminal .......................................................... 2-5
Setup Cloning to other terminals .............................. 7-5
Setup Menu
"Reset" bar code .................................................. 2-21
Baud Rate ............................................................ 2-21
Data Bits .............................................................. 2-21
Parity ................................................................... 2-21
RF Terminal Channel ............................................ 2-5
RF Terminal parameters ....................................... 2-5
Stop Bits .............................................................. 2-21
Terminal ID ........................................................... 2-5
SETUP MODE
using to program voice messages ......................... 7-2
Setup or playback voice messages ............................ 7-3
shelf label printing .................................................. 6-34
Shut Down Time ..................................................... 2-20
Shut Down Time feature ........................................... 1-4
SIGN ON Base to host programming ....................... 6-8
SIGN OUT
Base to host programming .................................... 6-9
missing the message .............................................. 5-3
Signing out in mid-transaction .................................. 5-2
Site survey ................................................................. 3-5
Site Test Mode - brief description of ....................... 3-1
Site Testing
channel changes ..................................................... 4-2
getting into ............................................................ 1-7
how it works .......................................................... 3-5
Site Testing in Progress message .............................. 4-2
Six beeps on power-up .............................................. 8-6
Skip Opening Screens ............................................... 2-8
sleep mode for RF Terminal ..................................... 3-3
SPEAKER VOLUME ............................................... 2-9
Stand mode ...................... See hands free laser scanning
Start Setup
scanning to enter Setup mode ............................... 2-2
Start/stop characters
transmitting for Codabar ........................................ 2-13
transmitting for Code 39 ..................................... 2-10
STATUS key
reserved for date/time only ................................. 6-12
using to determine battery life ................ 1-5, 2-8, 8-2
Steps for installation ................................................. 1-1
STK bar code ............................................................. 2-12
Stop Bits for serial printer ....................................... 2-21
Storage Tek bar code .................................................. 2-12
Storage Tek Tape Label code ..................................... 2-12
substitution errors ..................................................... L-2
Substitutions of data .................................................. L-3
sunlight problems, using aiming dot ......................... L-3
Surveying a site ......................................................... 4-1
T
T49 Holster for RF Terminal ....................................N-4
Tape library bar code .................................................. 2-12
TCP/IP Terminal Programming .............................. 6-23
Terminal ID
how to find out what yours is ............................... 1-7
use in Two-Way mode .......................................... 3-2
Terminal ID in One Way mode ................................ 3-5
Terminal keys
transmitting ASCII values .................................... 2-6
Terminal setup
Security Code ........................................................ 2-6
Terminal Setup Cloning
to other terminals .................................................. 7-5
Terminating a programming message ...................... 6-2
Terminator character ............................................... 2-16
Testing Base Station communications ............. 2-23, 8-5
Testing communication with a Relay ....................... B-4
Testing the Relay ...................................................... B-4
Thru-put considerations ............................................ 4-6
Time Set .................................................................. 2-19
time stamping in Terminal ........................................ 6-3
Tips for Using Voice Prompts .................................. 7-1
Trailing character trimming .................................... 2-17
TRANSMISSION FAILED ............................... 3-3, 3-4
Transmitting Bar Code ID's .................................... 2-12
Transmitting characters before or after
bar code data ....................................................... 2-15
Transmitting Codabar start and stop characters ............ 2-13
Transmitting EAN-8/UPC-E in original formats ....... 2-12
Transmitting through walls ........................................... 4-1
Trimming by bar code type
using bar code ID and postamble ....................... 2-17
using bar code ID and preamble/postamble ............. 2-16
Trimming characters from data...................... 2-15, 2-17
Trimming leading characters using Preamble ........ 2-15
Trimming trailing characters using Postamble ....... 2-16
TriOptic Code 39 ....................................................... 2-12
Troubleshooting ........................................................ 8-1
electrical noise problems with Relays .................. 4-4
wiring problems with Relays ................................ 4-4
Troubleshooting new installation ............................. 8-2
Turning on the R/F Terminal .................................... 1-4