FILE NO. 020-200001 SERVICE MANUAL COLOR TELEVISION N8PS Chassis DW65X91, DW56X91 (TAC9871) (TAC9871) TOSHIBA CORPORATION 1-1, SHIBAURA 1-CHOME, MINATO-KU, TOKYO 105-8001, JAPAN PRINTED IN U.S.A. Jan.
GENERAL ADJUSTMENTS TABLE OF CONTENTS CHAPTER 1 GENERAL ADJUSTMENTS SAFETY INSTRUCTIONS ........................................................................................................................................ 3 CRT ASSEMBLY REPLACEMENT AND MOUNTING .............................................................................................. 4 PICTURE TUBE COMPONENTS ADJUSTMENT ....................................................................................................
CHAPTER 1 GENERAL ADJUSTMENTS X-RAY RADIATION PRECAUTION 1. Excessive high voltage can produce potentially hazardous X-RAY RADIATION. To avoid such hazards, the high voltage must not be above the specified limit. The nominal value of the high voltage of this receiver is (A) kV at zero beam current (minimum brightness) under a 120V AC power source. The high voltage must not, under any circumstances, exceed (B) kV. Refer to table-1 for high voltage (A), (B). (See SETTING & ADJUSTING DATA on page 26) 2.
GENERAL ADJUSTMENTS CRT ASSEMBLY REPLACEMENT AND MOUNTING CAUTION : DO NOT LOOSEN THE HEX HEAD BOLTS WITH SPRINGS (12 PCS), BECAUSE THOSE ARE FOR SEALING OF CRT COOLANT. R G B Attention Serviceman The Hex Head Bolts with Springs. (see sketch) used on CRT assembly, are “NOT” Adjustment Screws DO NOT LOOSEN-FLUID LEAKAGE WILL OCCUR. SPECIFIC INFORMATIONS 8 o’clock 4 o’clock 4 Screws 4 Screws Lens Assembly CRT Assembly CRT Anode Cap Assembly S.V.M.
Anode Cap CRT REPLACEMENT (Same procedure for R, G, B) Reverse the removal procedures except the followings. 1. Anode Cable should be replaced with new one. See “SERVICING PRECAUTIONS” shown below. 2. Install silicon (T461B) to the CRT, replace the Anode cable and put enough silicon again on around the Anode Cap as illustrated. CAUTION: Align the Anode cable as illustrated on page 4. ADJUSTING PROCEDURE IN REPLACING CRT 1. R.G.B. CUTOFF (SCREEN VR) ADJUSTMENT (See owner's manual) 2. R.G.B.
SPECIFIC INFORMATIONS GENERAL ADJUSTMENTS WARNING : BEFORE SERVICING THIS CHASSIS, READ THE “X-RAY RADIATION PRECAUTION”, “SAFETY PRECAUTION” AND “PRODUCT SAFETY NOTICE” ON PAGE 3 OF THIS MANUAL. PICTURE TUBE COMPONENTS ADJUSTMENT DESCRIPTION OF NECK COMPONENTS 2 1 2. Enter the adjustment mode (see page 11). 3. Adjust the centering magnets for the RED, GREEN, and BLUE colors. (See CENTERING ADJUSTMENT.) 4.
6. Adjust the electric focus of RED as well as possible. (See RGB FOCUS ADJUSTMENT.) 7. Adjust the alignment and astigmatism of GREEN and BLUE using the above procedure for adjusting RED. Note: Normally the most clearly visible point of the scanning line is the sharpest point of the Green focus. 13. Check the GREEN focus of the whole screen and if necessary repeat steps from 10 to 12. 14. Fix the GREEN lens by tightening up its fixing screws. 15.
GENERAL ADJUSTMENTS 2. Select the adjustment mode, and adjust the data of item “HPOS” to 45H. 3. Press TV/VIDEO button on the Remote Control to display the white cross-bar. 4. Adjust G centering magnet so that the cross-bar pattern center comes to screen center. 5. Perform HEIGHT adjustment . (See page 16.) 6. Perform VERT. LINEARITY adjustment. 7. Perform WIDTH adjustment. (See page 16.) 8. Check whole quality of green line. 9.
Service parts are provided for each R, G and B. The contents of the parts are as follows. R G B 40" 23003518 23003519 23003520 56" 23003817 23003781 23003818 65" 23003780 23003781 23003782 REPLACEMENT OF HIGH VOLTAGE CABLE 1. When replacing Anode Lead or Anode Cap with new one, remove Lead Holder from old lead as shown in figure below, and put it on new lead. Do not throw away Lead Holder.
WARNING: BEFORE SERVICING THIS CHASSIS, READ THE "X-RAY RADIATION PRECAUTION", "SAFETY PRECAUGENERAL ADJUSTMENTS TION" AND "PRODUCT SAFETY NOTICE" ON PAGE 3 OF THIS MANUAL. SERVICE POSITION In order to assure the performance, processed wires shall be replaced after the repair work. Work procedures are as follows: 1. Remove the back board. 2. Remove lead wires. 3. Draw out the chassis. 4. Rest the chassis against the back cabinet, chassis as shown bellow.
1. ENTERING TO SERVICE MODE 1) Press CHANNEL t Button (on TV) and TV/SAT button (on TV) at the same time. S M 2. DISPLAYING THE ADJUSTMENT MENU 1) Press MENU button on Remote (or INFO button on TV). Adjustment mode Item S Press Data Press M 3. KEY FUNCTION IN THE SERVICE MODE The following key entry during display of adjustment menu provides special functions.
SPECIFIC INFORMATIONS GENERAL ADJUSTMENTS 4. SELECTING THE ADJUSTING ITEMS 1) Every pressing of CHANNEL s button in the service mode changes the adjustment items in the order of table-2. (t button for reverse order) Refer to table-2 for preset data of adjustment mode. (See SETTING & ADJUSTING DATA on page 26) 5. ADJUSTING THE DATA 1) Pressing of VOLUME s or t button will change the value of data in the range from 00H to FFH. The variable range depends on the adjusting item. 6.
SELF CHECK NO. 23XXXXXX POWER : 000 BUS LINE : OK BUS CONT : OK BLOCK : UV V1 V2 or QV01 QV01S SYNC 1 Part number of microprocessor (QA01) 2 Operation number of protection circuit (current limiter) . . . . “000” is normal. 3 BUS line check “OK” ................... Normal “SCL-GND” or “NG” ........... SCL-GND short circuit “SDA-GND” or “NG” ........... SDA-GND short circuit “SCL-SDA” or “NG” ............ SCL-SDA short circuit 4 BUS line ACK (acknowledge) check “OK” .....................
SPECIFIC INFORMATIONS GENERAL ADJUSTMENTS DESIGN MODE 1. ENTERING TO DESIGN MODE 1) Select the Service mode. 2) Press DVD TITLE and ENTER button on 3) Press MENU button on Remote. Remote by DVD mode. S D Press ITEM DATA Press (Design mode) (Adjustment mode) When QA02 is initialized, items “OPT0” and “OPT1” of DESIGN MODE are set to the data of the representative model of this chassis family. Therefore, because ON-SCREEN specification remains in the state of the representative of model.
:MAX :CNT :CNT :CNT :MAX :CNT :CNT :CNT CNTRAST BRIGHTNESS COLOUR TINT CONTRAST BRIGHTNESS COLOUR TINT Horizontal phase HPOS (Chassis) :MAX :CNT :CNT :CNT CONTRAST BRIGHTNESS COLOUR TINT SETTING Horizontal oscillation frequency NAMES fH. ADJ. (Chassis) High voltage adjustment (Unit) ITEMS – 15 – 0 3div SPECIFIC INFORMATIONS A 1) Adjust DC=0 of both wave forms to A=0.76±0.1[µs] the lowest line on the synchroscope. 2) Take measurement of 3 div.
GENERAL ADJUSTMENTS ITEM SUB-BRIGHTNESS (BRTC) ADJUSTMENT PROCEDURE 1. Constrict the picture height until the vertical retrace line appears adjusting the HEIGHT control on the MAIN board. 2. Adjust the CONTRAST to the minimum. 3. Enter the service mode, then select “BRTC” register. 4. Adjust the data value so the belt of vertical retrace line just disappear. 5. Adjust the CONTRAST for the desired contrast. 6. Adjust the HEIGHT control.
1. Press RESET button on TV or remote hand set. 2. Don’t put any signal in Video 1 jack. 3. Call up the adjustment mode display, then adjust the data of items RCUT, GCUT and BCUT to “40”. 4. Press TV (ANT)/VIDEO button on TV. 5. Gradually rotate R, G and B SCREEN volume of FOCUS PAC (page 8) clockwise or counterclockwise until the raster appears slightly on the CRT through the each lens, and leave them. (Look into the lens in order to check the raster.) 6. Press TV (ANT)/VIDEO button on TV again. 7.
SPECIFIC INFORMATIONS GENERAL ADJUSTMENTS CONVERGENCE ADJUSTMENT Adjust convergence from center to circumference in order. 1. Select the adjustment mode following the steps on page 11. RCUT 40H KEY FUNCTION IN THE CONVERGENCE ADJUSTMENT: Up : Selet Green color: Left : Blinking of cursor ON/OFF: Right: Adjust mode ON/OFF: Down: Erase Green line: Erase Red line: Erase Blue line: 2 button 3 button 4 button 5 button 6 button 7 button 8 button 0 button 100 button ENT button 2.
• Horizontal • Vertical 1442 mm 810 mm (1) FULL/WIDE2 339.5 291.0 145.5 GENERAL ADJUSTMENTS Adjusting Dimension of Each Picture Screen (65") 65 inches 16:9 screen size: 145.5 291.0 714 595 357 119 0 119 357 595 7 714 339.5 V. SPAN 48.5 mm H. SPAN 119 mm (2) WIDE1 341.0 293.0 143.0 0 -7.0 Pattern center 152.0 295.0 – 19 – 714.0 584.0 337.5 110.0 0 110.0 337.5 584.0 7.0 714.0 342.
GENERAL ADJUSTMENTS (3) 525P (STANDARD) 184 184 339.5 291.0 145.5 0 – 20 – 537 447.5 268.5 89.5 0 89.5 268.5 447.5 291.0 339.5 537 SPECIFIC INFORMATIONS 145.5 V. SPAN 48.5 mm H. SPAN 89.
ADJUSTING DIMENSION OF EACH PICTURE SCREEN (56") 16:9 screen size: GENERAL ADJUSTMENTS 1240 mm 700 mm 1. FULL/WIDE2 293.5 251.5 125.5 0 125.5 251.5 614 511.5 307 102.3 0 102.3 307 6 614 511.5 293.5 V. SPAN 41.9 mm H. SPAN 102.3 mm 2. WIDE1 294.5 253.0 123.5 0 -6 Pattern center 131.5 255.0 – 21 – 614.0 502.0 290.0 94.5 0 94.5 290.0 502.0 614.0 6.0 295.5 V. SPAN H.
GENERAL ADJUSTMENTS 3. 525P (STANDARD) 158 158 293.5 251.5 125.5 0 – 22 – 462 385 231 77 0 77 231 385 251.5 293.5 462 SPECIFIC INFORMATIONS 125.5 V. SPAN 41.9 mm H.
CRT REPLACEMENT When CRT is replaced, main deflection readjustment and color matching are required. Perform following procedures. 1. Replace two CRT’s of blue and red. 2. Perform horizontal adjustment for blue and red yokes on base of green CRT data. Mount yoke and velocity mod. coil alignment, pushing towards CRT without gap. 3. Adjust alignment of blue and red. (Refer Alignment adjustment for details.) 4. Rotating centering magnet, adjust CRT centers of red and blue to CRT center of green.
SPACER x2 SPACER x2 INSIDE 0 to 1 mm K503 FRONT PANEL K501 K502 LENTICULAR FRESNAL SPECIFIC INFORMATIONS GENERAL ADJUSTMENTS SCREEN AND MIRROR ALIGNMENTS OUT SIDE SMOOTH INSERT LENS BLACK STRIPES A260 PIECE SMOOTH BLACK STRIPES SPACER FRONT PANEL LENTICULAR FRESNEL SMOOTH A260 FRESNEL LENTICULAR FRONT PANEL INSERT BEZEL x2 A260 PIECE BEZEL x2 A260 PIECE A260 PIECE HOW TO CLEAN SCREEN When cleaning the screen, use a soft cloth so as not to damage the screen. 1.
Refer to table-1 for high voltage (B). (See SETTING & ADJUSTING DATA on page 26) 4. Vary the BRIGHTNESS to both extremes to be sure the high voltage does not exceed the limit under any conditions. CAUTION: When the following parts fail, check the High Voltage after replacing. Location No. T461 Z450 C404 C407 C408 R465 R466 R467 Q437 Name Flyback Trans.
GENERAL ADJUSTMENTS CHAPTER 2 SPECIFIC INFORMATIONS SETTING & ADJUSTING DATA X-RAY RADIATION PRECAUTION HIGH VOLTAGE AT ZERO BEAM: MAX HIGH VOLTAGE: Data 31.0 kV 31.
TV set (Replacementive: DW65X91) SPECIFIC INFORMATIONS Front view Behind the door INFO button IN—VIDEO 3 S-VIDEO RESET VIDEO AUDIO L/MONO R INFO TV/SAT button ENTER button ENTER MENU/ OK TV/SAT VOLUME CHANNEL POWER VIDEO 3 INPUTS MENU button CHANNEL / RESET button Remote sensor buttons buttons buttons VOLUME / buttons POWER indicator POWER button Rear view ANTENNA-IN SATELLITE-IN TOP OF CARD FACE DOWN PHONE JACK A B ACCESS CARD OPTICAL DIGITAL AUDIO OUT AUDIO CENTER CHANNEL IN
GENERAL ADJUSTMENTS Remote Control TV/VIDEO LIGHT* Transmit indicator* Program indicator Learning indicator TV/DVD/VCR/CABLE switch Set to “TV” to control the TV.
TV/CABLE function EDIT Channel 1 Press MENU, then press t (or s) until the SYSTEM OPTION menu appears. 2 Press : once. 3 Press t (or s) until "Signal Type" is highlighted. 4 Press : once. 5 Press s (or s) to highlit either "AIR/CABLE" which ever you use. 1 To erase a channel, select the channel you desire to erase by Edit Channel in TV, Setup of Profile Menu, and subsequently press the OK key. 2 To add a channel, take the same steps as in the case of erasure mentioned above.
GENERAL ADJUSTMENTS SPECIFIC INFORMATIONS THIS PAGE IS INTENTIONALLY LEFT BLANK.
CIRCUIT BLOCK DIAGRAM DM-1 POWER TUNER/LINK Fv=950-1450MHz +33V DSS_ANT +12V + 5V - 5V TELEPHONE MODEM MAIN MICON POWER 33V,12V,5 V LNB_PWR -5V,3.3V C/B_ANT_A C/B_ANT_B PFAIL POL LNB_PWR +18V LHCP PIP RF OUT /RF MOD IN GND SIGNAL SMART CARD READER AUDIO OUT L_Sel,R_Sel LFE,Center L_Sur,R_Sur Left,Right ANALOG PWR 33V,12V,-5V DIGITAL PWR LNB_CTL 3.
MECHANICAL DISASSEMBLY 1 Speaker Grille Removal 2 Control Panel Removal 3 Front Mask Removal A260 A001 A268 A103 screws screws K501 K502 K503 A253 A251 A202 screws A254 (A257, A258) A102 4 Shield Plate, Lens Removal 5 Mirror Removal 6 Back Board Removal 7 Light Box Removal screws screws K111 K112 K113 K601 screws screws A424 screws screws screws – 33 – – 34 –
CHASSIS REPLACEMENT PARTS LIST NOTICE: • The part number must be used when ordering parts, in order to assist in processing, be sure to include the Model number and Description. • The PC board assembly with * mark is no longer available after the end of the production. Models : DW65X91, DW56X91 Capacitors ............. CD : Ceramic Disk PF : Plastic Film EL : Electrolytic Resistors ...............
SPECIFIC INFORMATIONS Location No. Part No.
Part No. Description Location No. Part No.
SPECIFIC INFORMATIONS Location No. Part No.
Part No. Description Location No. Part No.
SPECIFIC INFORMATIONS Location No. Part No. Description Location No. Part No.
Part No. Description Location No. Part No.
SPECIFIC INFORMATIONS Location No. Part No.
Part No.
SPECIFIC INFORMATIONS Location No. Part No.
Part No. Description Location No. Part No.
SPECIFIC INFORMATIONS Location No. Part No. Description Location No. Part No.
Part No. Description CZ225 CZ226 CZ227 CZ228 CZ229 CZ230 CZ231 CZ232 CZ233 CZ234 CZ235 CZ236 CZ291 CZ292 24781100 24781390 24815102 24814103 24814103 24092293 24814103 24092293 24781330 24092293 24781100 24092293 24232103 24232103 Chip, 10pF, ±0.5pF%, SL Chip, 39pF, SL Chip, 0.001?F, ±10% Chip, 0.01?F, +80%, -20% Chip, 0.01?F, +80%, -20% Chip, 0.1?F, +80%, -20%, 25V Chip, 0.01?F, +80%, -20% Chip, 0.1?F, +80%, -20%, 25V Chip, 33pF, SL Chip, 0.1?F, +80%, -20%, 25V Chip, 10pF, ±0.5pF%, SL Chip, 0.
SPECIFIC INFORMATIONS Location No. R387 R392 R393 R394 R395 R396 R397 R398 R401 R402 R403 R405 R406 R407 R407 R408 R409 R410 R412 R413 R414 R415 R416 R417 R418 R419 R421 R422 R423 R424 R425 R426 R427 R428 R429 R430 R431 R432 R433 R434 R435 R436 R437 R438 R439 R440 R441 R442 R447 R448 R449 R450 * R451 * R452 * R453 R454 R455 R456 R458 R459 R460 R461 R462 R463 Part No. Description Location No. Part No.
Part No. Description Location No. Part No.
SPECIFIC INFORMATIONS Location No. Part No. Description Location No. Part No.
Part No. Description Location No. Part No.
SPECIFIC INFORMATIONS Location No. Part No. Description Location No. Part No.
Part No. Description Location No. Part No.
SPECIFIC INFORMATIONS Location No. Part No. Description Location No. Part No.
Part No. Description Location No. Part No.
SPECIFIC INFORMATIONS Location No. Part No. Description Location No. Part No.
Part No. Description Location No. Part No.
SPECIFIC INFORMATIONS Location No. Part No. Description Location No. Part No.
Part No. Description Location No. Part No.
SPECIFIC INFORMATIONS Location No. Part No. Description Location No. Part No.
Part No.
SPECIFIC INFORMATIONS Location No. Part No.
Part No.
SPECIFIC INFORMATIONS Location No. Part No.
Part No.
SPECIFIC INFORMATIONS Location No. Part No. Description Location No. Part No.
Part No. Description Location No. Part No.
SPECIFIC INFORMATIONS Location No. Part No. Description Location No. Part No.
D413 D430 D431 D432 D433 D435 D436 D438 D439 D440 D441 D442 D443 D445 D451 D452 D453 D454 D456 D471 * D472 D473 D474 D475 D476 D484 D489 D490 D491 D513 D521 D522 D523 D525 D526 D531 D532 D601 D602 D603 D604 D607 D608 D611 D612 D614 D615 D616 D704 D705 D715 D721 D801 D801B D804 D805 D806 D807 D808 D808B D809 D809B D810 D811 Part No.
SPECIFIC INFORMATIONS Location No. Part No.
Part No.
SPECIFIC INFORMATIONS Location No. Part No.
Location No. Part No. Description PICTURE TUBE * V901R 23003780 * V902G 23003781 * V903B 23003782 Protector Coupling R 6, DW65X91 Protector Coupling G 6, DW65X91 Protector Coupling B 6, DW65X91 Location No. Part No.
SPECIFIC INFORMATIONS THIS PAGE IS INTENTIONALLY LEFT BLANK.
C3200 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 15 14 13 12 11 10 09 08 07 06 05 04 03 02 01 15 14 13 12 11 10 09 08 07 06 05 04 03 02 01 CZ41 25 R2354 R2353 Q2350 E B 26 1 16 R248 Q205 R2284 27 R2352 E Q206 B R251 C2239 28 R249 4 R2283 29 C2351 R2351 C2350 R2280 C2233 R2279 30 DJ DF DI DA DG DB DD DE 5 DH DC 31 B 3 4 2 1 32 C2237 C2238 C2234 C2235 C2240 C2241 RZ40 E RB97 33 L870 RZ46 RB96 RB94 CD08 6 34 - L871 L872 E RZ45
POWER BOARD PB9114 BOTTOM (FOIL) SIDE G + GJ11 9 8 12 7 C843 C844 B 5 D844 4 2 3 1 + Q840 + D845 L840 D821 2 3 R848 A G R847 4 5 6 7 P805 D854 D853 D823 D852 – 78 – 1 NC 8 GND 7 ACP 6 POWER2 5 POWER1 4 RESET 3 +5V-1 2 BB110 1 D846 K D851 - C846 + D822 R832 R815 R826 R816 R802 L805 D806 C821 D803 R813 NC 8 NC 7 C816 6 NC 5 4 1 C828 L819 4 POWER2 -21V 3 POWER1 -21V 2 GND GND 1 R814 +5V-1 GND – 77 – B1-V-0 T-D 6 PROTECT
DEF BOARD PB9097 BOTTOM (FOIL) SIDE D444 R341 Q307 GND B 3 P404 C Y B1-V-0 T-D C409 4 L451 5 E 1 P417 G 8 C408 2 D413 R441 Q404 C404 O C Q448 6 C421 Q415 C489 D R350 VCC C495 R458 R426 D406 R427 C420 R424 C486 Q447 R462 + B B + Q436 D C496 D474 C E B R4039 1 D475 2 Q435 C497 E D371 D489 B R417 Q438 B E 4 R4040 Q492 R4038 3 162 R463 E C475 163 B + E E R442 P406 164 C484 R461 G 5 C FB + D472 C472 Q429 R455 + Q437 1 71 72 7
7 5 4 BLUE 3 2 P714 P723 1 7 (V) (H) 6 5 4 RED 3 2 1 (V) 7 (H) P713 6 5 4 GREEN 3 2 P715 1 4 3 2 1 Q752 P860 RQ33 D7760 9 RQ19 CQ17 + R7746 R7747 Q759 RQ35 R7832 B R7835 B +9V-1 E Q788 E Q786 E Q789 R7731 R7736 R7726 8 7 6 5 4 3 2 1 – 82 – QQ18 E - R7833 - - R7823 R7709 - - C7729 C7726 - R7707 - D7741 + CQ14 C7737 Q766 RQ11 - - LQ12 1 CQ21 + CQ20 + RQ12 B DQ13 R7711 1 Q790 GND B Q791 E +5V-D B E 7 GND B E 6 +5V-D R7837 Q787 5
REAR A/V BOARD PB9100 OSD-MIXER BOARD PB9104 BOTTOM (FOIL) SIDE BOTTOM (FOIL) SIDE GJ01 L2301 C2317 CS67 CS66 + + R L GND V GND C GND Y DVD GND SGA CS54 RS82 + CY40 RV140 RS51 CS38 RS06 CS16 CV02 RS04 CV08 CV05 CV62 RV84 CS28 DV08 DV07 DV09 + RS02 + CS51 RV141 RV142 RV124 CV24 CV21 LV06 CV 66 E QV22 RV128 CV67 RV64 CV03 RS53 DV13 DV12 B E QV10 RV81 RY80 CV64 B B RV127 CV68 B QV21 E E CV 65 QV23 RV24 CW12 RV28 PB12 SGV PIP-VIDEO V-AV RS8
OSD/MICON BOARD PB9099 VCD/FV-CON BOARD PB9096 BOTTOM (FOIL) SIDE BOTTOM (FOIL) SIDE D532 + C531 1 2 PA13 3 1 2 3 PA11 4 5 6 1 42 RT62 RT61 RT60 RT20 RR84 RR81 + RR82 DT01 RB27 RR83 RR 116 RR 117 RT22 + CT42 B CT70 CT43 + QB71 RT50 RT51 DA44 RA56 + E RR68 DR60 B RR114 RR79 RR08 QR60 RR62 QR08 01 B B B CM QR09 3 + E E B RR16 B B RR 18 QR12 CR69 P507B QR10 E RR 20 QR11 RR 21 RR 22 E RR91 RR92 RM33 DR90 + RR76 RR74 RR75 CM42 CM43 1 CM33
CRT DRIVE (R) BOARD PB9102-1 BOTTOM (FOIL) SIDE + R975 C964 R978 + B E B B R966 7 6 5 4 3 2 C908 R962 E B + D967 1 R901 R961 D908 R973 E R971 E R976 Q963 Q966 R969 R977 D961 D962 R963 R964 R907 C901 C902 B + R938 B L901 R9410 R970 L962 R968 + C9410 - 11 10 9 8 7 6 5 4 3 2 P915A 1 R9402 D903 C962 P914B R965 C963 D907 Q964 D902 R905 R993 Q965 R974 R972 B E R908 R9400 R981 + R980 R909 C904 Q961 E C961 E E B R906 - - L
CRT DRIVE (B) BOARD PB9102-3 BOTTOM (FOIL) SIDE D936 R959 C926 P916B 1 2 3 4 5 6 7 8 9 10 11 D931 R9620 R953 D932 B1-V-0 T-D C921 C924 C922 D933 BLUE-DRIVE + D926 P905 + R951 D C9610 R950 R954 D934 R952 E G2 BLUE SCREEN G1 R923 R988 Q923 K R960 G971 V903A + C H R989 B P903 H P923 B R9 3 3 62 D927 L923 R930 C925 D928 E Q924 2 B R9613 B D925 C9200 B R9610 C9601 R925 R9609 R921 D924 R9605 R927 Q921 1 E Q9604 C9602 D921 E B R920 R9606
FRONT-CONTROL BOARD PB9102-4 RB09 1 1 2 3 4 5 6 7 E - DB05 8 10 RB01 9 RB11 RB10 DB01 CB01 + BOTTOM (FOIL) SIDE RO QB01 2 3 SA01 SA02 SA03 SA04 SA07 SA06 SA08 CH UP CH DN VOL UP VOL DN TV/ MENU INFO - DSS B 6 KB01 PB10 POW RB04 5 4 SA05 LE RI GB01 PB11 B1-V-0 T-D + FRONT A/V BOARD PB9102-5 CV122 RV120 + Y 3 2 B1-V-0 T-D + + RH80 SA09 R 1 RH81 RV121 C CH80 V CV121 CH81 RV123 PB13 LV120 RV122 CV120 139 138 137 136 135 134 133 1
NF/FRONT BOARD PB9109-1 BOTTOM (FOIL) SIDE 7 6 5 4 3 2 PF07 1 PF09 5 4 3 2 1 1 2 3 4 5 6 7 8 PF11 9 PF05 2 1 3 11 10 9 8 7 6 5 4 3 2 1 9 8 7 6 PF06 5 4 3 2 PF10 1 13 1 PF08 TCL-751 1 14 2 13 8 1 7 PF02 12 2 1 13 2 1 11 PF03 PF01 PF04 NF/TOP BOARD PB9109-2 BOTTOM (FOIL) SIDE PF20 PF18 9 1 PF19 14 1 1 2 PF26 3 5 4 3 PF25 2 1 7 10 PF12 9 1 PF13 14 1 3 PF14 TCL-751 – 90 – 5 2 9 1 6 PF21 3 2 1 6 5 18 1 PF17 4
UPCON BOARD PB9111 LX321 CX314 + RX331 RX322 QX310 QX301 28 CX321 RX321 RX343 CX384 RX332 RX334 CX339 CX337 CX375 RX312 CX373 CX364 QX330 CX387 RX361 RX 349 RX 342 RX 341 QX307 CX354 RX311 CX368 CX358 CX310 + CX309 CX359 CX355 CX193 RX198 RX199 CX194 CX195 CX196 RX189 CX186 CX185 CX184 CX183 RX188 RX179 RX178 CX173 CX174 CX175 CX136 CX116 RX196 RX186 RX354 CX154 CX134 CX114 RX353 QX144 RX157 CX147 CX146 RX153 CX144 RX149 RX129 QX143 QX142 RX148 +
SUB-POWER BOARD PB9101 BOTTOM (FOIL) SIDE P804 3 1 F820 125V10A P812 D882 CAUTION LIVE AREA P813 P815 Z801 Z802 B1-V-O T-D C851 C858 T870 C8300 T871 D8300 + C8302 3 2 D8303 P806 SR87 1 R8300 D8302 T872 C8304 + D8301 5 3 1 C8303 4 2 Q8302 C852 C853 C854 Q8300 D8304 E B D8305 R8301 Q8301 T873 B R8303 R8302 E CH84 QH80 RH83 C8301 + RH84 P873 RH85 3 4 1 2 3 4 1 2 3 4 P874 2 CH83 CH82 DH81 DH82 1 + RH82 P814 P808 RH88 1 2 3 RH87 – 9
DIGI-CONV BOARD PB7296G RH186 CH206 CH207 RH187 RH008 4 3 1 2 CH046 13 12 11 10 9 8 7 1 6 14 15 5 4 3 CH195 CH194 RH182 CH196 CH197 RH180 RH181 CH226 CH212 CH213 RH192 CH224 RH199 RH191 RH190 CH229 CH223 CH210 CH211 CH230 LH004 5 CH192 CH237 CH232 CH234 CH231 CH233 RH198 RH195 RH048 RH047 RH046 RH045 RH044 6 CH044 LH120 7 CH048 8 CH014 CH042 CH015 QH140 2 23545347 CH047 9 10 CH045 11 CH043 CH016 RH005 12 9 LH123 PH001 CH041 13 14 RH007 CH
GENERAL ADJUSTMENTS TERMINAL VIEW OF TRANSISTORS 1 2SD2253 (old) 2SC5243 E C 2 2SC3852 2SD1763A 2SC1569 2SC4544 2SA1788 2SA1306 2SA1186A 3 2SC752GTM 2SC2482 2SC2655 2SC4721P B C B SPECIFIC INFORMATIONS BC RN2203 RN2201 RN2004 RN1203 RN1204 RN2204 RN1205 RN1202 RN1201 7 2SD1554 2SD2253 2SD1556 2SC5143 8 C E BC ON4409 E E E 2SC752 2SA562TM 2SA1015 2SC1815 2SC2878 2SC1740S 2SC2120 2SA9335 5 2SA1788 E E 6 4 C B CB – 94 – B E CB
NTSC standard ATSC standard DSS standard CHANNEL COVERAGE ANALOG/ DIGITAL/ VHF: 2 through 13 UHF: 14 through 69 Cable TV: Mid band (A-8 through A-1, A through I) Super band (J through W) Hyper band (AA through ZZ, AAA, BBB) Ultra band (65 through 94, 100 through 125) 1 — 999 POWER SOURCE 120 V AC, 60 Hz POWER CONSUMPTION 270W AUDIO POWER 14 W + 14 W SPEAKER TYPE Two 6-1/4 inches (16 cm) round VIDEO/AUDIO TERMINALS S-VIDEO INPUT (VIDEO 1/VIDEO 2/VIDEO 3) Y: 1 V(p-p), 75 ohm, negative sync.
FILE NO. 020-200001 SERVICE MANUAL COLOR TELEVISION N8PS Chassis DW65X91, DW56X91 (TAC9871) (TAC9871) TOSHIBA CORPORATION 1-1, SHIBAURA 1-CHOME, MINATO-KU, TOKYO 105-8001, JAPAN PRINTED IN U.S.A. Jan.
