SwingArm–Dual™ Assembly Instructions Part no.
SwingArm–Dual™ Installation Instructions Important Safety Instructions Read and understand all these safety instructions before using this product. Do not mount the clamp base or the grommet base on an unstable surface (any surface that will not hold the base firmly). For safety reasons, the internal gas-strut of the SwingArm–Dual™ is preadjusted at the factory to the lowest force for the prevention of arm body recoil during installation.
SwingArm–Dual™ Installation Instructions List of Boxes Box # Label Qty I Desk Clamp 1* Ix Desk Bolt 1* II Short Pole 1 III Dual Mount 1 IV Monitor Arm 2 * Note that either Box I or Box Ix will be included, depending on the style of base purchased. List of Parts Part Illustration Box Description Qty I-1 I Clamp Base 1 I-2 I Clamping bracket 1 I-3 I Base cushion 1 I-4 I M5 hex wrench 1 I-5 I M2.5 Hex Wrench 1 I-6 I Button head cap screw M8 X 1.
SwingArm–Dual™ Installation Instructions Part Illustration Box Description Qty Ix-1 Ix Grommet Base 1 Ix-2 Ix U-Bracket 1 Ix-3 Ix M8 X 1.25 X 130mm Thread Rod 1 Ix-4 Ix M8 Washer 1 Ix-5 Ix M8 X 1.25 Wing Nut 1 Ix-6 Ix Base cushion 1 Ix-7 Ix M5 hex wrench 1 Ix-8 Ix M2.5 Hex Wrench 1 II-1 II 14” Pole 1 II-2 II Cable manager Velcro® strips 2 III-1 III Dual Mount Clamp 1 III-2 III Plastic Spacer 30mm OD, 18.
Part Illustration SwingArm–Dual™ Installation Instructions Box Description Qty IV-1 IV Assembled arm 2* IV-2 IV End Cap 2* IV-3 IV Round-head screw M4 X 0.7 X 10mm 8* IV-4 IV Round-head screw M4 X 0.7 X 6mm 8* IV-5 IV 75mm Monitor plate 2* * Quantities for Box IV parts show total from both boxes Workrite reserves the right to make changes to its products without notice. No liability is assumed for any misprinting or error in this publication. Copyright 2008.
SwingArm–Dual™ Installation Instructions Step 1: Attach Clamp Base to Work Surface Step 1x: Attach Grommet Base to Work Surface (If you are using the grommet base, please skip to Step 1x.) A: Remove the center hole from the base cushion (Ix-6), then attach it to the underside of the base (Ix-1), aligning the hole in the base with the hole in the protector. Thread the M8 Thread Rod (Ix-3) into the bottom of the base. B: Attach 14” pole (II-1) to base, securely tighten 4 set screws (already in place).
SwingArm–Dual™ Installation Instructions Step 2: Attach Monitor Arms to Monitors A: Place monitor carefully on a clean, flat surface, face down. B: Attach the monitor arm (IV-1) to the back of the monitor with four screws, using a Phillipshead screwdriver (not included). Use the mounting screws provided by your monitor manufacturer if available. Otherwise, use the screws provided that best fits your monitor (IV-4 or IV-5).
SwingArm–Dual™ Installation Instructions Step 3: Attach Pivot Base and Arms A: Place the pivot pins (III-3) and the large plastic spacers (III-2) onto the dual mount clamp (III-1). B: Place the dual mount clamp assembly onto the pole with the ratchet handle facing the back. Position the mount so that the top of it is approximately 7” from the desk for a 15” monitor, 8” for a 17” monitor or 9” for a 19” monitor. Tighten the dual mount using the ratcheting handle.
Your SwingArm—Dual is now installed and it is time for the final adjustments. If your monitor is too light or too heavy for the factory-set tension, the arm will raise or lower too easily (or even on its own). If this is the case, you need to adjust the vertical movement. SwingArm–Dual™ Installation Instructions Adjustment screw Step 4: Vertical Movement Adjustment A: Set the monitor arm at a 90° angle and locate the adjustment screw on the top of the arm joint.
SwingArm–Dual™ Installation Instructions Step 6: Final Touches: Cable Management A: Thread the monitor cable through the plastic sleeve mounted on the lower side of the monitor arm, taking care to leave enough slack in the cable for full monitor movement on both sides of the sleeve. B: Secure attached hook and loop strips around monitor cables, again leaving enough slack at both ends of the arm for full movement of the arms.
