Workrite Sierra HX™ Crank Assembly Instructions for 2-Leg Crank models #1500160 - Rev e
Parts grouped by carton A Tabletop (size and shape differ for each model) Qty: 1 E Leg Qty: 1 B Long Brace Qty: 1 C Short Brace Qty: 2 H ¼-20 x ⅝" Button head Machine Screws Qty: 21 K Shallow Hex Shaft Qty: 1 I Crank Handle Assembly Qty: 1 L Deep Hex Shaft Qty: 1 M #12 x ¾" Pan Head Sheetmetal Screw OR Qty: 32 N " Allen Wrench Qty: 1 D Crank Tube Qty: 1 E Leg Qty: 1 F Medium Brace Qty: 1 G Leg Cap Qty: 1 OR F Medium Brace Qty: 1 G Leg Cap Qty: 1 d 1 a J #12 x ½" Self Tapp
Workrite Sierra HX™ 2-Leg Crank Workcenters - Assembly Instructions 1 b ...continued Placement of the legs is very important. Take the time now to lay out the Legs (E), Leg Braces (B, C, and F), Crank Tube (D), and Leg Caps (G) on the floor in the proper location. Note that the right leg will be on your left and vice versa when the assembly is seen from the back.
Workrite Sierra HX™ 2-Leg Crank Workcenters - Assembly Instructions 4 Attach Legs to Hex Shafts and Crank Tube Turn Leg Assembly upside down. a Right Leg: Insert short end of Deep Hex Shaft (L) into leg. Slide Crank Tube (D) over Deep Hex Shaft. Left Leg: Insert short end of Shallow Hex Shaft (K) into leg. Slide Crank Tube (D) over Shallow Hex Shaft. K L D D Right Leg 5 a Left Leg Secure Long Brace Attach Long Brace to back of right Leg Cap using Button Head Screws (J).
Workrite Sierra HX™ 2-Leg Crank Workcenters - Assembly Instructions 6 Attach Short and Medium Braces to Leg Assembly a Use power drill to attach both Short Braces (C) using Button Head Screws (H). Do not tighten screws completely - allow them to slide left and right in brace. b Attach Medium Braces (F) to sides of Legs using Button Head Screws (H). If you have a 24” deep or less worksurface, use the holes to the rear of the brace as shown.
Workrite Sierra HX™ 2-Leg Crank Workcenters - Assembly Instructions 7 b ...continued Position leg assembly to align mounting holes to pre-drilled holes in Top (A) - it might be necessary to adjust braces - then attach loosely using Pan Head Screws (M). If you use an electric screwdriver, be sure it is on the lowest torque setting to avoid stripping the threads.
Workrite Sierra HX™ 2-Leg Crank Workcenters - Assembly Instructions 9 a Base-Only Front-Crank Models: Loosely Secure Table Base to Tabletop Position the leg assembly on the face-down table top. Center the assembly on the table so that neither of the side legs overlap the edge. Measure carefully to ensure that your table will be positioned correctly as detailed below before drilling.
Workrite Sierra HX™ 2-Leg Crank Workcenters - Assembly Instructions 10 Base-Only Top-Crank Models: Loosely Secure Table Base to Tabletop a Position the leg assembly on the face-down table top. Center the assembly on the table so that neither of the side legs overlap the edge. Measure carefully to ensure that your table will be positioned correctly as detailed below before drilling. Mark ¾" hole for crank handle: Trace around outside of leg bracket before removing leg assembly.
Workrite Sierra HX™ 2-Leg Crank Workcenters - Assembly Instructions 11 Tighten All Screws and Flip Table Over a b c Tighten all Sheetmetal Screws connecting handle, braces and legs to desk. Flip table over and adjust Leveling Glides if required so that table is steady and does not rock. Top-Crank models only: Insert Crank Handle into hole in worksurface over the right leg so that it engages the gearbox. Turn Handle to raise or lower table.
Workrite Sierra HX™ 2-Leg Crank Workcenters - Assembly Instructions 13 Adjust Leveling Guides If necessary, adjust leveling guides on table feet to level the worksurface. Cleaning instructions To clean the Sierra HX legs, apply cleaner to a soft cloth. Suggested cleaners: • Windex • Formula 409 —Do NOT use solvents —Do NOT saturate or spray cleaners directly to table base 10 Workrite Ergonomics | 800.959.9675 www.workriteergo.
