TABLE OF CONTENT dmx inTERFACEs ........................................................... 3 control SOFTWARE ...................................................... 8 dmx TOOLs .................................................................. 12 LIGHTING CONTROLLERS ...............................................14 WIRELESS DMX SYSTEMs ............................................. 16 VIDEO DEVICEs ............................................................. 17 dmx DRIVERS.................................
2
LM 2 MK II Bidirectional DMX/USB interface This compact tool is a bidirectional DMX/USB interface (DMX input/output interface). You can use it: As a ‘USB to DMX interface’ to control a full 512 channel lighting system from a unique computer. As a ‘DMX to USB interface’ so DMX signal can control the computer and interact with the software. LM 2 MK II is a very interesting tool for lighting designers.
LM 3E artnet device LM 3E is a DMX to Ethernet converter that sends DMX signals in an existing Ethernet network using ArtNet protocol. It has been preset to be automatically integrated into protocol ArtNet, so no configuration is required. Nevertheless, it is fully configurable also using the integrated webserver (LM 3E and LM3R) Thanks to its group selector, several LM 3E units can be used in a same network, transporting thus various DMX universes together.
LM 3R LM 3R2 artnet device LM 3R and LM 3R2 are the easiest way to transport DMX signals through an Ethernet network, no matter if it is and already existent or a one-time network. For this purpose the system requires emitters (LM 3E or ArtNet console) which introduce a DMX signal into the Ethernet network, and receivers (LM 3R and LM 3R2) that pull out the DMX signal from the Ethernet network. The system is quick and easy to install, because it doesn’t requires any kind of configuration.
LM 5 control interface for audio, lighting and AV AV and lighting control within everyone´s reach! In spite of the many improvements of the industry, lighting control has always been complicated for non specialized users. Conventional lighting consoles have been replaced by lighting software but both options offer an intuitive interface that can be easily managed by end-users.
Control any installations from your smartphone, tablet or computer. The overall installation can be controlled with a smartphone, a tablet or a computer. It is very intuitive so everyone can use it without any technical knowledge. Thanks to the OSC open protocol (www.opensoundcontrol.org), it is suitable for mobile devices (iOS and Android) and PC&MAC computers: LM 5 turns your smartphone/tablet/computer into an intuitive console for audio and lighting purposes.
OSCillation software OSCillation is a professional control application for any software or hardware compatible with OSC. Its modular interface allows the creation of costumized interfaces for any kind of device or installation, from a simple volume control to an advanced multizone control, OSCillation fits any project. OSCillation is avalaible for Android, Mac and Windows, helping us to make easy its integration in all applications. FEATURES - Control of multiple OSC servers simultaneously (Multitarget).
OSCillation software Do you want to get the most out of OSCillation app? Visit OSCillation official web site (www.workproaudio.com/OSCillation) and find out a wide range of useful and interesting resources such as manuals, videotutorials, layouts ready to be downloaded and installed and, of course, the free OSCillation app itself. This application is available for Android, Windows PC and MAC and is also compatible with third-party layouts like those designed by TouchOSC (app developed by Hexler.net).
YOOM software YOOM is a flexible lighting control application, easy to use with 3 modes (RGB, 6 CH and 512 CH). YOOM is the easiest way to programme scenes and positions from any system with Windows OS. YOOM includes an event generator to create programmed tasks to trigger cue lists and play multimedia files (audio and video) according to a specific calendar. Its compatibility with LightMouse devices (really easy to configurate and use) make easier the lighting system integration in all applications.
YOOM software - 3 different interfaces to use depending on the requirements. YOOM is in fact 3 different consoles designed to fit in different kind of applications. The interface changes according to the selected mode in order to provide a more specific working mode: - Full mode: with 512 DMX faders. Simple, direct and powerful at the same time. - RGB Architectural mode: designed for 1 RGB zone where exist different presets, cues and/or cue lists to trigger at the right time with emulated buttons.
SRD 6 DMX / rdm splitter SRD 6 is a DMX splitter with 6 outputs isolated from the inputs and between them. It also allows to fit it within a RDM network with compatible devices. Thanks to that, SRD 6 makes posible that these devices (such as compatible moving heads) submit feedback of some incorporated functions (temperature,etc). The possibility to work with DMX or RDM is done by an internal rear switcher.
DMXnet Series DMX devices DMXnet 4 and 8 are a fully configurable ArtNet node of 4 universes (DMXnet 4) and 8 universes (DMXnet 8). Thanks to these units, users have the opportunity to send data through an Ethernet network, with up to 512 DMX channels per universe. Data transfered using ArtNet nodes is faster than when using DMX networks. This solution is recommended for the control of LED fixtures that use many channels, but also to send DMX information in a big event through an unique Ethernet cable.
HomeLED lighting controllers HomeLED is a 6A (2 each channel) driver and 3 DMX channels controller appropriate to control RGB LED fixtures. Its wall-mount design coupled with an intuitive handling allow using it for any lighting installations in exhibition halls, pubs and nightclubs, shops and even for domestic use.
Control ONE DIM ONE / DIM ONE MK II lighting controllers CONTROL ONE is a single channel DMX wall-mount controller. Its dimensions for standard electrical box , design and functionality allow to integrate it into spaces or applications where a dimming control based on a single DMX channel is required. The control is done through the integrated encoder, adding the functionality, when clicked, to dim between the selected value and its opposite.
DMX AIR MK II wireless dmx transmitter / receiver This evolution in DMX AIR devices allows to use them as transmitter or receiver according to the installation needs simply by pressing the incorporated button. Thus, it is not necessary to have stock of emitters and receivers. A set of several DMX AIR MK II solves any desired arrangement in an installation to operate either as a sender or receiver.
VMX 4 video device It is a composite video multiplexer. Its connection also incorporates 4 L + R audio inputs. The purpose of the device is to select one of 4 input sources and send it to the output. This selection can be done in 2 ways: - Using the appropriate front button. - Through DMX signal. In the latter case, VMX 4 provides a DMX control channel, whose value determines which input signal is sent to the output.
MINIDIM 1 MINIDIM RGB 2 Single channel dimmer / RGB dimmer MINIDIM 1 is a single channel dimmer perfectly adequate to one colour LED fixtures. It supports DMX inputs and outputs to link other units as 0-10 V analog signals. There are two operating modes available: starting address channel (DMX) and increasing percentage of output intensity (manual). This compact dimmer offers a simple solution for configuration and control and is capable of handling up to 6A load.
MINIDIM RGB PRO MINIDIM 8 RGB DIMMERs MINIDIM RGB PRO is the updated version of this 3 channels dimmer. Its design allows a maximum load of 12A (4A per each RGB colour). This unit is perfectly suitable to control RGB LED strips. Thanks to its compact size, it is possible to put it next to the lighting source, being unnoticed and getting rid of bulky dimmers. It allows to connect a LED strip of DC 12V as well as DC 24V.
UNIDIM 1 DUODIM 1 and 2 CHANNELS DIMMERS UNIDIM 1 and DUODIM are ultra compact DMX dimmers featuring one or two channels (max. load: 10A. each channel). They can be used as a chaser to remotely switch lighting effects like scanner or moving head. Thanks to its compact size, it can be easily placed on DIN rails or trusses. The software provides an intuitive menu for parameters edition like maximum dimmer levels or DMX address channel.
D 40 K3 12 channels dimmer D 40 K3 is a high performance dimmer of WORK Pro. It supports DMX and Analog signals, with 12 channels of 16 A each. This is the evolution of the D 40 K2 model. It includes relevant improvements, like a new internal electronic and bi-pole magneto-thermal circuit breakers. In addition, listening to our customer needs, it now includes double schucko connectors per channel on rear panel.
D 66 K3 12 Channels modular Dimmer D 66 K3 is the most powerful digital dimmer from WORK Pro. It features in 3 HU rack units 12 channels with 25 A each. This is the perfect tool for fixed installations and touring, as it provides reliability, power and flexibility. It features components for user is safety and a correct control of the dimmer. Double circuit breakers (1P+N) ensure electrical safety in case of short-circuits and electrical overload, cutting both phase and neutral conductors.
D 66 K3 FEATURES - 12 channel digital dimmer. - DMX 512 and analog (DC 0-10 V) signal input, possibility to operate with both signal types simultaneously. - Load capacity: 25 A per channel. - Total 18 kW (mono-phase) and 55 kW (tri-phase). - Individual DMX address and patchable response curve for each input channel (linear, quadratic, quadratic inverse, on/off). - Preheat level on each channel. - DMX buffer against connections fails. - 2 pole circuit-breaker (1P+N) for each channel.
TOURDIM 48 RACK OF DIMMERS This rack of dimmers based on the D 66 K3 model has been designed for almost any touring applications and rental companies, being perfect for live shows. TOURDIM 48 has four D 66 K3 dimmers that provides 48 dimming channels up to 16A each one it. Incorporates an independent circuit breaker for each channel. All its channels and the response curve are patchable.
TOURDIM 48 Closed rack FEATURES - 48 channels of 16 A with independent circuit breakers (1P+N). - Each block of 12 channels has its own circuit breaker for residual current. - Powerlock connector of 400 A for supply. - 16 pin multi-connector for output channels. - XLR5 Pin connector (bypass) on rear panel for inputs and outputs. - Cooling system on the side of the rack. - LED indicators for the output level of each channel. - 16x2 character LCD display.
ESD / EST Series voltage regulators The voltage regulator has become an essential tool for the mobile installations with voltage variations problems. Taking into account the almost systematic presence of equipment such as computers, lighting controllers, etc, voltage regulators are the safest tool to keep the equipment save from sudden voltage changes. This effect is even more accentuated when the voltage is supplied from a mobile supply unit (generators, etc), because its current is not stable.
ESD 10K voltage regulator ESD 10 K is a voltage regulator that maintains a constant output supply when voltage varies between 140 and 250 V (with 220 V devices) or between 60 and 130 V (with 110V devices). It is possible to connect a 10 kVA fix load. As many fixture performance depends on voltage, it is essential to ensure the regulation and control on these values.
ESD 5K/2 EST 519/2 voltage regulators These 2 regulators maintain a constant output supply when voltage oscillates between 140 and 250 V. It is possible to connect a 22 A fix load. If their features and operational modes are equal, the enclosures make the diference between them. ESD 5K/2 includes handles for an easy transport and has been designed in a 19” rack format for its integration in fixed installations and an input voltage selector (60V-130 V / 140V-260 V).
EST 1K / 2K voltage regulator These two units maintain a constant output supply when voltage oscillates between 140 and 250 V AC. They allow 1000 VA (EST 1K) or 2000 VA (EST 2K) load connection. Both devices feature different protections to ensure output signal integrity: protections against overvoltage, overload, or short circuits. They also have a circuit breaker on their rear panel. To avoid noises coming from ON/OFF switch, They also feature a time delay circuit (3 or 6 sec.
FLYBOX 630 power distributor FLYBOX 630 is a tri-phase power distributor with 63 A housed into a 10 HU 19” rack, giving a professional supply distribution system perfectly protected and with a total control over its many outputs. Its high quality components and oversized wiring, ensure a really reliable devices supply. All system is housed into a 10 HU 19” rack with corners and metallic protection profiles and handles for transport. FRONT PANEL SHOWS: - Connection input (through 3P+N+E - 63A connector).
FLYBOX 320 power distributor FLYBOX 320 is a tri-phase power distributor with 32 A housed into a 8 HU 19” rack, giving a professional supply distribution system perfectly protected and with a total control over its many outputs. Its high quality components and oversized wiring, ensure a really reliable devices supply. All system is housed into a 8 HU 19” rack with corners and metallic protection profiles and handles for transport. FRONT PANEL SHOWS: - Connection input (through 3P+N+E - 32A connector).
ALPHABETICAL PRODUCT INDEX Control ONE ��������������������������������������������������������������������������������������������������� 15 D 40 K3 ������������������������������������������������������������������������������������������������������������ 21 D 66 K3 ������������������������������������������������������������������������������������������������������������ 22 DIM ONE / DIM ONE MK II ���������������������������������������������������������������������������������� 15 DMX AIR MK II ���
