MODEL WSP-i450 (4inch Rugged Printer) Rev. 4.0 WOOSIM SYSTEMS Inc. #501, Daerung Technotown 3th, 448, Gasan-Dong, GeumChun-Ku, Seoul, Korea Tel : +82-2-2107-3700 Fax : +82-2-2107-3707 URL: http://www.woosim.com All specifications are subjected to change without notice http://www.woosim.
WSP-i450 Rev. 4.0 ¦ Copyright WSP-i450 4inch Rugged printer operator’s manual. Copyright ⓒ2012 by Woosim Systems Inc. All rights reserved. The information contained in this manual is the property of Woosim Systems Inc. And may not be reproduced in whole or in part without the prior written permission of Woosim Systems Inc. ¦ Trademark a registered trademark of Woosim Systems Inc. All other trademark are the properties of their respective companies.
WSP-i450 Rev. 4.0 ¦ Introduction The WSP-i450 is the ideal solution for Mobile banking system , Retail, point of sales, Credit card Transaction, other traveling and mobile computing etc. The general features of WSP-i450 printer are as follows: u Compact size (150.9×135.7×63.3mm) u Light weight(735g) for true mobility [standard] u Very silent printing thru direct thermal printing method u High speed (70mm/sec, MAX) u High resolution(203dpi : 8dots/mm). u UART(RS-232C or TTL), Bluetooth Ver2.
WSP-i450 Rev. 4.0 ¦ Operating Precautions Please follow the precautions below to enjoy and maintain the full performance of the printer. u Using the Printer ● Be careful not to drop or bump the printer on a hard surface. ● Do not install the printer in direct sunlight or such areas.
WSP-i450 Rev. 4.0 ¦ Note This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. These equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
WSP-i450 Rev. 4.0 CONTENTS 1. Outline. .........................................................................................................................................8 1.1. Model classifications. .......................................................................................................8 1.2 Product Part Number System ..........................................................................................8 1.3. Specifications. ........................................................
WSP-i450 Rev. 4.0 5.1. Control panel. ..................................................................................................................28 5.2. The self test ......................................................................................................................29 5.3. Using the Accessory .......................................................................................................29 5.3.1. Using the Shoulder strap......................................................
WSP-i450 Rev. 4.0 1. Outline. 1.1. Model classifications. WSP-i450 ( ) ( ) Model Interface A1 : UART/Bluetooth (Standard) Power None : DC 8.4V 1.2 Product Par t Number System Model name / Interface Spec. Wired S40 Wireless SC30 A RS-232C 1 Bluetooth W25 B TTL 2 IrDA C USB 3 Wireless LAN D RS-485 0 None E Parallel Z None . . . Example) 1. Porti-S40 2. Porti-SC30 Serial/Bluetooth Part No. ⇒ S40/A1 Bluetooth Only Part No. ⇒ SC30/Z1 http://www.woosim.
WSP-i450 Rev. 4.0 1.3. Specifications. Item Specifications Print method Direct thermal line printing Characters per line 92cpl (MAX) Character size Eng: 9*24dots, 12*24dots Kor: 16*24dots, [24*24dots] Simplified/Traditional Chinese, Arabic, Cyrillic, Russian, Optional Characters Tukish, Greek, Japanese, Persian, Latin9 and Others upon request. Resolution 203dpi, 8dots/mm Print width 4-inch (104mm, 832dots) Print speed 70mm / sec (MAX) Dimension 150.9×135.7×63.
WSP-i450 Rev. 4.0 Item Specifications LCD 128×32 Dots FSTN (Blue LED Backlight) Battery Rechargeable 7.4V DC, 2200mAh (Li-ion) Battery duration 1 hour continuous printing Battery charger Environment conditions MCBF(Mean Cycle Between Failure) Input (100~250V AC, 50~60Hz) Output(8.4VDC/0.
WSP-i450 Rev. 4.0 2. Setting up the printer. 2.1. Printer & Accessories Your printer box should include these items. If any items are damaged or missing, please contact your dealer for assistance. Communication cable Battery charger adaptor WSP-i450 Battery Pack Thermal roll paper Belt clip ▼ OPTIONAL MSR Shoulder strap Smart Card 1 SAM http://www.woosim.
WSP-i450 Rev. 4.0 2.2. Printer Features ▶ Part Name http://www.woosim.
WSP-i450 Rev. 4.0 2.3. Dimensions http://www.woosim.
WSP-i450 Rev. 4.0 2.4. Replacing paper roll. Note : Be sure to use paper rolls that meet the specifications. Do not use paper rolls that have the paper glued to the core because the printer can not detect the paper end correctly. 1. Make sure that the printer is not receiving data; otherwise, data may be lost. 2. Open the paper cover as the “One-Touch” way by pressing the button in the arrow direction like the picture. 3. Insert a new paper roll as shown. 4.
WSP-i450 Rev. 4.0 2.5. Power supply 2.5.1. Specified power supply The following specification is requested for Power supply. Battery Charger : DC 8.4V/0.8A Avoid using power supply which its power capacity of power current is extremely high. 2.5.2. Installing the SAM Card and the batter y NOTE : ● Before installing or removing the battery pack, ensure the printer is OFF. ● If the printer is not used for long period of time, remove the battery pack from the printer.
WSP-i450 Rev. 4.0 2.5.3. Recharging the batter y pack For recharging the battery pack, install the battery pack in the printer. Insert the Battery Charger to the charge connector of the printer. NOTE : ● While charging the printer, turn off the printer power. ● Do not remove the battery during charging. ● The battery is consumable parts and when purchasing, compared to the use hour is gradually decreases.
WSP-i450 Rev. 4.0 2.6. Set operation mode In keeping on pressing the Feed and Power button simultaneously until after the ERROR lamp blinks 5 times, the printer comes out at the circumstance to change the printer mode. (refer Table 2) ** Only the printer which support iOS Bluetooth interface comes out at the circumstance to change the printer mode. (Bluetooth Mode or Boluetooth(iAP) Mode). ** Manipulation methods : 1.
WSP-i450 Rev. 4.0 u Press MODE & POWER Button during the Error Lamp flickers 5 times. ® You will see present COMMUNICATION mode in the LCD. (UART) ® Press the POWER Button twice. And then, interface mode has set to Bluetooth mode. u When you press FEED button once. ® You will see present BAUD RATE mode in the LCD. (9600 bps) ® Press POWER Button 3 times. And then, BAUD RATE has set to 57,600 bps. u When you press FEED button once. ® You will see present DATA BIT mode in the LCD.
WSP-i450 Rev. 4.0 u When you press FEED button once. ® You will see present MARK mode in the LCD. (Use) ® Press POWER Button once. And then the mark has set to Mark Gap/Hole. u When you press FEED button once. ® You will see present SENSOR mode in the LCD. (High) ® Press POWER Button once. And then the sensor has set to Sensor Auto. u When you press FEED button once. ® You will see present POWER DOWN mode in the LCD. (5 minutes) ® Press POWER Button once.
WSP-i450 Rev. 4.
WSP-i450 Rev. 4.0 MODE OPTION Low Medium1 Sensor Medium2 High Auto No use 1 minute Power Down 2 minute 3 minute 4 minute 5 minute < Table 2 > 2.7. Confirmation of the Wireless-LAN information 2.7.1. MAC Address printing u MAC address which is set to the printer can be printed out in pressing the Power and Feed button simultaneously and taking off them shortly after the ERROR lamp blinks 2.7.2.
WSP-i450 Rev. 4.0 3. Interface 3.1. UART(RS-232C or TTL) & USB The WSP-i450 printer has a UART(RS-232C or TTL) & USB interface and is connected by means of a 5 pin mini USB socket. In the following table, the signals present on the Mini- USB socket are listed: ① UART(RS-232C or TTL) Pin No. Name Direction Function 1 TxD Output Transmit Data 2 RxD Input Receive Data 3 CTS - - 4 NC. - - 5 GND - Ground http://www.woosim.
WSP-i450 Rev. 4.0 ② USB NOTE : Pin No. Name Function 1 VCC +5V 2 DM DATA “-” 3 DP DATA “+” 4 NC. - 5 GND Ground ● When data receiving, when it removes the Communication cable, it loses a data. http://www.woosim.
WSP-i450 Rev. 4.0 3.2. Bluetooth Category Specification Bluetooth Spec. Bluetooth Ver2.1 + EDR / Class2 (10m) Frequency Range 2.4GHz ISM BAND Data Transmission Rate 57600bps Fixed. Data bit 8 Data bit Fixed. Parity bit No parity Fixed. Stop bit 1 Stop bit Fixed. 3.3. Wireless LAN Category Specification Interface Network Protocol TCP, UDP, IP, ICMP, ARP, DHCP, PPPoE IEEE802.
WSP-i450 Rev. 4.0 3.4. Card Reading & Smart Card inser t Insert the Smart Card into slot with micro chip facing down. Please take notice that Magnetic Stripe Card should be swapped in direction of arrow. Card can be read in both http://www.woosim.
WSP-i450 Rev. 4.0 4. Smar t Card Module 4.1. General Spec. u Contact Smart Card Reader Module for ISO/IEC-7816 u Support Asynchronous Protocol T=0,T=1 u Smart Card Connection - Short Circuit Current Limitation - 6KV ESD Protection on whole Smart Card Interface - Connector : Friction Type with Smart Card presence detection u 1 SAM (Security Application Module) u EMV Level 1 Certified http://www.woosim.
WSP-i450 Rev. 4.0 4.2. Communication Protocol Sequence 4.2.1. Regular Operation Host Command Module Execution Response 4.2.2. Irregular Operation (Communication Error) 500ms timeout Host Command Command Module Host Command Command is Command Executio Command Error Module CheckSumEr Executio r n http://www.woosim.
WSP-i450 Rev. 4.0 5. Using the printer 5.1. Control panel. u BUTTON - FEED Button : When the printer is on, paper can be feed manually by pressing and holding the FEED button for more than one second. - POWER Button: ① When of 5 or more seconds presses and power comes to on or off. ② After pressing the POWER and the FEED button simultaneously, if the ERROR lamp 5 turn signals POWER button is converted with MODE functions.
WSP-i450 Rev. 4.0 5.2. The self test The self test procedure will check most of the printer functions. For self test, turn on the power while holding down the FEED Button. The Self-Test checks the following : 1) Make sure paper roll has been installed properly. 2) The Self-Test prints the current printer status, which provides the control ROM version and the communication method setting. 3) After printing the current printer status, Self-Test will print a pattern using the built-in character set.
WSP-i450 Rev. 4.0 5.3.2. Using the Belt clip Following the instruction of the arrow, please put the belt clip in the hole and turn and fix the screw to the right by using a thing like a coin. Afterward, you can use it like the picture below http://www.woosim.
WSP-i450 Rev. 4.0 6. Consumable Par ts. 6.1. Recommended paper. Type : Thermal Paper Paper width : 113mm Paper thickness : 60±5㎛ Outer diameter : Ø50mm or less Recording side : Outside of roll Cautions 1. Do not paste the paper to the core. And the roll paper which has Near end mark printing on its near end is recommended. 2. Chemicals or oil may change the color of paper, or printed Characters may fade. 3. Change of paper color starts from approx 70 ℃.
WSP-i450 Rev. 4.0 7. Revision Histor y Date Version Comments Dec. 24. 2010 2.0 2.2 Part Name Additional (Sensor) Feb 17. 2011 3.0 2.6.1 GAP/HOLE SENSOR SETTING * 4inch Industrial Printer → 4inch Rugged Printer Aug. 10. 2012 4.0 P3 : u Agency Approvals of the image update p17 : Bluetooth Mode or Boluetooth(iAP) Mode setting addition http://www.woosim.
