Specifications

ManualsBrandsWOOSIM ManualsComputer equipmentPORTI-PC40

ٻۃۏۏۋڕڊڊےےےډےۊۊێۄۈډھۊۈٻ

ٻٻٻٻٻٻٻٻٻٻ

ٻٻٻٻٻٻ

ٻٻٻٻ

MODEL PORTI-PC40

WOOSIM SYSTEM Inc.

#501, Daerung Technotown 3th,

448, Gasan-Dong, GeumChun-Ku,

Seoul, Korea

Tel : +82-2-2107-3700

Fax : +82-2-2107-3707

URL: http://www.woosim.com

(2 Inch Printer with MSR )

All specifications are subjected to change without notice

Summary of content (67 pages)

PAGE 1
‫ٻٻٻٻٻٻٻٻٻٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ MODEL ‫ٻ‬ PORTI-PC40 ‫ٻ‬ ‫ٻ‬ (2 Inch Printer with MSR ) ͑ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ G ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ WOOSIM SYSTEM Inc. #501, Daerung Technotown 3th, 448, Gasan-Dong, GeumChun-Ku, Seoul, Korea Tel : +82-2-2107-3700 Fax : +82-2-2107-3707 URL: http://www.woosim.
PAGE 2
‫ ٻ‬Copyright ‫ٻ‬ Porti-PC40 2 Inch printer operator’s manual. ‫ ٻ‬Copyright གྷ2005 by Woosim System Inc. ‫ ٻ‬All rights reserved. ‫ ٻ‬The information contained in this manual is the property of Woosim ‫ ٻ‬System Inc. and may not be reproduced in whole or in part without ‫ ٻ‬the prior written permission of Woosim System Inc. ‫ٻ‬ ‫ٻ‬ ‫ ٻ‬Trademark ‫ٻ‬ a registered trademark of Woosim System Inc. ‫ٻ‬ ‫ ٻ‬All other trademark are the properties of their respective companies.
PAGE 3
‫ ٻ‬Introduction ‫ ٻ‬The Porti-PC40 is the ideal solution for Mobile banking system , Retail, ‫ ٻ‬point of sales, Credit card Transaction, other traveling and mobile computing etc. ‫ٻ‬ ‫ ٻ‬The general features of Porti-PC40 printer are as follows: ‫ٻ‬ ‫ٻ‬ X Pocket size(105 x 80.4 x 45.7mm) ‫ٻ‬ X Light weight(286g) for true mobility. ‫ٻ‬ X Very silent printing thru direct thermal printing method. ‫ٻ‬ X High speed(50mm/sec) ‫ٻ‬ X High resolution(203dpi : 8dots/mm).
PAGE 4
‫ ٻ‬Operating Precautions ‫ ٻ‬Please follow the precautions below to enjoy and maintain the full ‫ ٻ‬performance of the printer. ‫ٻ‬ ‫ ٻ‬XUsing the Printer ‫ٻ‬ Ɣ Be careful not to drop or bump the printer on a hard surface. ‫ٻ‬ Ɣ Do not install the printer in direct sunlight or such areas.
PAGE 5
CONTENTS 1. Outline .............................................................................................................................................7G 1.1. Model classifications ............................................................................................................7G 1.2. Specifications........................................................................................................................8G 2. Setting up the printer ..........................................
PAGE 6
‫‪Appendix ...........................................................................................................................................
PAGE 7
‫‪XUGvG G G G G G G G G G G G G G G G G G G G G G G G G G G G G G G G‬‬ ‫‪XUXUGtGG‬‬ ‫ٻ‬ ‫ٻڄٻٻٻڃٻٻڄٻٻٻڃٻٻ‪PORTI–PC40‬‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‪Model name‬‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫‪Interface‬‬ ‫ٻ‬ ‫ٻٻڄڞڍڎڍڈڮڭڃۇڼۄۍۀڮٻڕۀۉۊک‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫‪Power‬‬ ‫ٻ‬ ‫ٻڱڏڍۙڍڌٻڞڟٻڕٻۀۉۊک‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ڒ‬ ‫ٻۈۊھډۈۄێۊۊےډےےےڊڊڕۋۏۏۃٻ‬
PAGE 8
XUYUGzG ‫ٻ‬ ‫ٻ‬ Item Description ‫ٻ‬ Printing method Direct thermal line printing ‫ٻ‬ Characters per line 42cpl ‫ٻ‬ Character size Eng. : 9*24dots, 12*24dots ‫ٻ‬ Resolution 203dpi, 8dots/mm ‫ٻ‬ Print width 2-inch (48mm, 384dots) ‫ٻ‬ Printing speed 50mm / sec ‫ٻ‬ Dimensions 105 x 80.4 x 45.
PAGE 9
YUG G zGGGG G G G G G G G G G G G G G G G G G YUXUG|G ‫ ٻ‬Your printer box should include these items. If any items are damaged or missing, please ‫ ٻ‬contact your dealer for assistance.
PAGE 10
‫‪YUYUGvGGGGG‬‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ڋڌ‬ ‫ٻۈۊھډۈۄێۊۊےډےےےڊڊڕۋۏۏۃٻ‬
PAGE 11
‫‪YUZUGkG‬‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ڌڌ‬ ‫ٻۈۊھډۈۄێۊۊےډےےےڊڊڕۋۏۏۃٻ‬
PAGE 12
YU[UGpGGGGGG ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ Note : Be sure to use paper rolls that meet the specifications. ‫ٻ‬ Do not use paper rolls that have the paper glued to the ‫ٻ‬ core because the printer cannot detect the paper end ‫ٻ‬ correctly. ‫ ٻ‬1. Make sure that the printer is not receiving data; otherwise, data may be lost. ‫ ٻ‬2. Open the paper roll cover by applying your finger on both side of printer, ‫ٻ‬ push it up when the lock is released as shown in the drawing.
PAGE 13
‫ ٻ‬5. Be sure to note the correct direction that the paper comes off the roll. ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ ٻ‬6. Pull out a small amount of paper and then close the cover, as shown. ‫ٻٻ‬ ‫ٻٻ‬ ‫ٻٻ‬ ‫ٻٻ‬ ‫ٻٻ‬ ‫ٻٻ‬ ‫ٻٻ‬ ‫ٻٻ‬ ‫ٻ‬ ‫ ٻ‬7. Tear off the paper as shown.
PAGE 14
YU\UGzGG G ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ The following specifications are requested for Power supply.
PAGE 15
ZUGpG G G G G G G G G G G G G G G G G G G G G G G G G G G G G G G ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ The Porti-PC40 printer has an RS-232C serial interface is connected by means of a 9p D-sub. ‫ٻ‬ In the following table, the signals present on the connector are listed: ‫ٻ ٻ‬ ‫ٻ ٻ‬ ‫ٻ ٻ‬ ‫ٻ ٻ‬ Pin No.
PAGE 16
‫ ୔ ٻ‬RS-232C Technical Specifications ‫ٻ‬ DATA TRANSFER RATE ‫ٻ‬ WORD LENGTH ‫ٻ‬ ‫ٻ‬ : 8 Data Bits 1 Stop Bit SIGNAL LEVELS ‫ٻ‬ ‫ٻ‬ : 9600 Baud : Mark or Logical 1 = -3 to -15 VDC Space or Logical 0 = +3 to +15VDC HANDSHAKING : XON / XOFF ‫ٻٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻٻ‬ ‫ٻۈۊھډۈۄێۊۊےډےےےڊڊڕۋۏۏۃٻ‬ ‫ڑڌ‬
PAGE 17
[UG|GGG G G G G G G G G G G G G G G G G G G G G G G G G [UXUGjGG ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ X Button ‫ٻ‬ - FEED Button : ‫ٻ‬ ‫ٻ‬ Press the FEED button once to advance paper one line. You can also hold ‫ٻ‬ down the FEED button to feed paper continuously. ‫ٻ‬ X Panel Lamp ‫ٻ‬ ‫ٻ‬ -POWER : The POWER lamp is on whenever the printer is on. ‫ٻ‬ -ERROR : This indicates an error such as paper end, or cover open, etc.
PAGE 18
[UYUG{GGG ‫ٻ‬ The self-test checks whether the printer has any problems. If the printer ‫ ٻ‬does not function properly, contact your dealer. The self-test checks the following; ‫ٻ‬ 1. Make sure paper roll has been installed properly. ‫ٻ‬ 2. Turn on the power while holding down the FEED button. The self-test begins. ‫ٻ‬ 3. The self-test prints the current printer status, which provides the control ROM version and ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ the communication method setting. 4.
PAGE 19
\UGjGwG G G G G G G G G G G G G G G G G G G G G G \UXUGyGG ‫ ٻ‬Type ‫ ٻ‬Paper width : Thermal Paper : 57mm ‫ ٻ‬Paper thickness ‫ ٻ‬Outer diameter ‫ ٻ‬Recording side ‫ٻ ٻ‬ ‫ٻ‬ : 65±5 Mm : Ø40mm or less : Outside of roll Cautions ‫ٻ‬ ‫ٻ‬ 1. Do not paste the paper to the core. And the roll paper which has ‫ٻ‬ ‫ٻ‬ Near end mark printing on its near end is recommended. 2. ‫ٻ‬ ‫ٻ‬ Characters may fade. 3.
PAGE 20
‫‪\UYUGwGG‬‬ ‫ٻ‬ ‫ٻ‬ ‫ٻٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ڋڍ‬ ‫ٻۈۊھډۈۄێۊۊےډےےےڊڊڕۋۏۏۃٻ‬
PAGE 21
]UGwGjGmG ‫ٻ‬ ‫ٻ‬ ഘ‫ٻۏێۄڧٻێڿۉڼۈۈۊڞٻڿۀۏۍۊۋۋېڮٻ‬ ‫ٻ‬ Command Name Function Type Page ‫ٻ‬ HT Horizontal tab Print position 37 ‫ٻ‬ LF Print and line feed Print 23 FF Print and return to standard mode Print 24 Real-time status transmission Status 52 ESC FF Print data in page mode Print 24 ESC SP Set right-side character spacing Character 27 ESC ! Select print mode Character 28 ESC $ Set absolute print position Print position 34 ESC * Select bit-image mode
PAGE 22
‫ ٻ‬Command ‫ ٻ ٻ‬ESC T ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ Name Function Type Page Select print direction in page mode Print position 47 ESC W Set printing area in page mode Print position 41 ESC X 4 Define user-defined bit-image Bit image 50 ESC \ Set relative print position Print position 35 ESC Z Print 2D barcode Barcode 56 ESC a Select justification Print position 36 ESC c 5 Enable/disable panel buttons Panel button 33 ESC d Print and feed n lines Print 24 ESC
PAGE 23
]UXUGwGjG ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ The PORTI-PC40 supports the following commands for printing character and advancing paper: Command Name ‫ٻ‬ LF Print and line feed ‫ٻ‬ ESC J Print and feed paper ‫ٻ‬ ESC d Print and feed n lines ‫ٻ‬ FF Print and return to standard mode(in page mode) ‫ٻ‬ ESC FF Print data in page mode ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ LF [Name] Print and line feed [Format] ASCII LF HEX 0A Decimal 10 ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ [Description] current line spacing.
PAGE 24
‫ ٻ‬ESC d n ‫[ ٻ‬Name] Print and feed n lines ‫[ ٻ‬Format] ASCII ESC d n ‫ٻ‬ HEX 1B 64 n ‫ٻ‬ Decimal 27 100 n ‫[ ٻ‬Range] 0n ‫[ ٻ‬Description] Prints the data in the print buffer and feeds n lines. ‫[ ٻ‬Note] 1) This command sets the print starting position to the beginning of the line. ‫ٻ‬ 2) This command does not affect the line spacing set by ESC 2 or ESC 3. ‫[ ٻ‬Reference] ESC 2, ESC 3 255 ‫ ٻ‬FF ‫[ ٻ‬Name] Print and return to standard mode in page mode.
PAGE 25
]UYUGsGzGjG ‫ ٻ‬The PORTI-PC40 supports the following commands for setting line spacing. These ‫ٻ‬commands only set the line spacing; they do not actually advance the paper. The line spacing ‫ٻ‬set using these commands affects the results of LF and ESC d and paper feeding by using the ‫ٻ‬FEED button.
PAGE 26
‫ٻ‬ 3) The GS P command can change the horizontal (and vertical) motion unit. ‫ٻ‬ However, the value cannot be less than the minimum vertical movement amount, ‫ٻ‬ and it must be in even units of the minimum vertical movement amount.
PAGE 27
‫ ٻ‬ESC SP n ‫[ ٻ‬Name] Set right-side character spacing. ‫[ ٻ‬Format] ASCII ESC SP n ‫ٻ‬ HEX 1B 20 n ‫ٻ‬ Decimal 27 32 n ‫[ ٻ‬Range] 0 n 255 ‫[ ٻ‬Description] Sets the character spacing for the right side of the character to [n x horizontal or ‫ٻ‬ vertical motion units] inches. ‫[ ٻ‬Note] 1) The right side character spacing for double-width mode is twice the normal ‫ٻ‬ value. When characters are enlarged, the right side character spacing is n times ‫ٻ‬ normal value.
PAGE 28
‫ٻ‬ ‫ٻ‬ n Character set n Character set ‫ٻ‬ 0 U.S.A 6 Sweden ‫ٻ‬ 1 France 7 Italy ‫ٻ‬ 2 Germany 8 Spain ‫ٻ‬ 3 U.K 9 Norway ‫ٻ‬ 4 Denmark 10 Denmark II ‫[ ٻ‬Default] n=0 ‫ٻ‬ ‫ ٻ‬ESC ! n ‫[ ٻ‬Name] Select print mode. ‫[ ٻ‬Format] ASCII ESC ! n ‫ٻ‬ HEX 1B 21 n ‫ٻ‬ Decimal 27 33 n ‫[ ٻ‬Range] 0 അ n അ 255 ‫[ ٻ‬Description] Select print mode(s) using n as follows,.
PAGE 29
‫[ ٻ‬Note] 1) When both double-height and double-width modes are selected, quadruple size ‫ٻ‬ characters are printed. ‫ٻ‬ 2) The printer can underline all characters, but can not underline the space set by ‫ٻ‬ HT. ‫ٻ‬ 3) The thickness of the underline is that selected by ESC -, regardless of the ‫ٻ‬ character size. ‫ٻ‬ 4) When some characters in a line are double or mode height, all the characters on ‫ٻ‬ the line are aligned at the baseline.
PAGE 30
‫ٻ‬ following data is not underlined, and the underline thickness set before the mode is ‫ٻ‬ turned off does not change. The default underline thickness is 1 dot. ‫ٻ‬ 4) Changing the character size does not affect the current underline thickness. ‫ٻ‬ 5) Underline mode can also be turned on or off by using ESC !. ‫ٻ‬ Note, however, that the last received command is effective.
PAGE 31
‫[ ٻ‬Note] 1) Only the lowest significant bit of n is valid. ‫ٻ‬ 2) This command is enabled only when processed at the beginning of a line in ‫ٻ‬ standard mode. ‫ٻ‬ 3) When this command is input in page mode, the printer performs only internal flag ‫ٻ‬ operations. ‫ٻ‬ 4) This command does not affect printing in page mode. ‫ٻ‬ 5) In upside-down printing mode, the printer rotates the line to be ‫ٻ‬ printed by 180 degree and then prints it.
PAGE 32
‫ٻٻ‬ ‫ٻٻ‬ Hex Decimal Width Hex Decimal Height ‫ٻٻ‬ 00 0 1 (normal) 00 0 1 (normal) ‫ٻٻ‬ 01 1 2 (double width) 10 16 2 (double height) ‫ٻٻ‬ 02 2 3 20 32 3 ‫ٻٻ‬ 03 3 4 30 48 4 ‫ٻٻ‬ 04 4 5 40 64 5 ‫ٻٻ‬ 05 5 6 50 80 6 ‫ٻٻ‬ 06 6 7 60 96 7 ‫ٻٻ‬ 07 7 8 70 112 8 ‫ٻٻ‬ Character Height Selection Character Width Selection ‫[ ٻ‬Notes] 1) This command is all characters effective ‫ٻ‬ 2) If n is outside of the defined range, this command is ignored.
PAGE 33
‫[ ٻ‬Notes] 1) When the LSB is 0, white/black reverse printing mode is turned on. ‫ٻ‬ 2) When the LSB is 1, white/black reverse printing mode is turned off. ‫ٻ‬ 3) Only the lowest bit of n is valid. ‫ٻ‬ 4) This command is available for built in characters and user defined characters. ‫ٻ‬ 5) When white/black reverse printing mode is on, it also applied to character ‫ٻ‬ spacing set by ESC SP. ‫ٻ‬ 6) This command does not affect the space between lines.
PAGE 34
‫ٻ‬ 2) When the panel buttons are disabled, none of them are usable when the printer ‫ٻ‬ cover is closed. ‫ٻ‬ 3) In this printer, the panel buttons is the FEED button. ‫ٻ‬ 4) In the macro ready mode, the FEED button are enabled regardless of the settings ‫ٻ‬ of this command; however, the paper cannot be fed by using these buttons.
PAGE 35
‫[ ٻ‬Description] ‫ٻ‬ Set the distance from the beginning of the line to the position at which subsequent ‫[ ٻ‬Notes] ‫ٻ‬ 1) The distance from the beginning of the line to the print position is [(nL + nH x 256) x (vertical or horizontal motion unit)] inches. ‫ٻ‬ 2) Setting outside the specified printable area are ignored. ‫ٻ‬ 3) The horizontal and vertical motion unit are specified by GS P. ‫ٻ‬ 4) The GS P command can change the horizontal (and vertical) motion unit.
PAGE 36
‫ٻ‬ 2) Any setting that exceeds the printable are is ignored ‫ٻ‬ 3) When pitch N is specified to the right; nL + nH x 256 = N ‫ٻ‬ When pitch N is specified to the left (the negative direction), use the complement of ‫ٻ‬ 65536. ‫ٻ‬ 4) The print starting position moves from the current position to [N x horizontal or ‫ٻ‬ vertical motion unit)] ‫ٻ‬ 5) The horizontal and vertical motion unit are specified by GS P. ‫ٻ‬ 6) The GS P command can change the horizontal (and vertical) motion unit.
PAGE 37
‫[ ٻ‬Notes] 1) The command is enabled only when processed at the beginning of the line in ‫ٻ‬ standard mode. ‫ٻ‬ 2) If this command is input in page mode, the printer performs only internal flag ‫ٻ‬ operations. ‫ٻ‬ 3) This command has no effect in page mode. ‫ٻ‬ 4) This command executes justification in the printing area.
PAGE 38
‫ ٻ‬ESC D n1…nk NUL ‫[ ٻ‬Name] Set horizontal tab positions. ‫[ ٻ‬Format] ASCII ESC D n1…nk NUL ‫ٻ‬ HEX 1B 44 n1…nk 00 ‫ٻ‬ Decimal 27 68 n1…nk 0 ‫[ ٻ‬Range] 1 <= n <= 255 ‫ٻ‬ 0 <= k <=32 ‫[ ٻ‬Description] Set horizontal tab position ‫[ ٻ‬Notes] 1) n specifies the column number for setting a horizontal tab position from the ‫ٻ‬ beginning of the line. ‫ٻ‬ 2) k indicates the total number of horizontal tab positions to be set.
PAGE 39
‫ ٻ‬GS L nL nH ‫[ ٻ‬Name] Set left margin. ‫[ ٻ‬Format] ASCII GS L nL nH ‫ٻ‬ HEX 1D 4C nL nH ‫ٻ‬ Decimal 29 76 nL nH ‫[ ٻ‬Range] 0 അ ‫[ ٻ‬Description] Set the left margin using nL and nH. ‫[ ٻ‬Notes]1) The left margin is set to [(nL+nHx256)] x (horizontal motion unit) inches. nL അ 255, 0 അ nH അ 255 ‫ٻ‬ ‫ٻ‬ ‫ٻٻ‬ ‫ٻٻ‬ ‫ٻ‬ ‫ٻٻ‬ ‫ٻ‬ 2) This command is effective only processed at the beginning of the line in standard ‫ٻ‬ mode.
PAGE 40
‫ ٻ‬GS W nL nH ‫[ ٻ‬Name] Set printing area width ‫[ ٻ‬Format] ASCII GS W nL nH ‫ٻ‬ HEX 1D 57 nL nH ‫ٻ‬ Decimal 29 87 nL nH ‫[ ٻ‬Range] 0 അ nL അ 255, 0 അ nH അ 255 ‫[ ٻ‬Description] Sets the printing area width to the area specified by nL and nH. ‫[ ٻ‬Notes] 1) The printing area width is set to [(nL+nHx256)] x horizontal motion unit inches. ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ 2) This command is effective only processed at the beginning of the line.
PAGE 41
‫ٻٻ‬ ‫ٻٻ‬ ‫ٻٻ‬ ‫ٻٻ‬ ‫ٻٻ‬ ‫ٻ‬ If the printing area width cannot be extended sufficiently, the right space is ‫ٻ‬ reduced. ‫ٻٻ‬ 9) If the width set for the printing area is less than one line in vertical, the ‫ٻ‬ following processing is performed only on the line in question when data ‫ٻ‬ other than character data(e.g.
PAGE 42
‫ٻ‬ dy = [(dyL + dyH * 256)] * (vertical motion unit) ‫ٻ‬ The printing area is set as shown in the figure below. ‫[ ٻ‬Note] 1) If this commands is input in standard mode, the printer executes only internal flag ‫ٻ‬ operation. This command does not affect printing in standard mode. ‫ٻ‬ 2) If the horizontal or vertical starting position is set outside the printable area, the ‫ٻ‬ printer stops command processing and processes the following data as normal data.
PAGE 43
‫ٻٻ‬ ‫ٻٻ‬ ‫ٻٻ‬ ‫ٻٻ‬ ‫ٻٻ‬ ‫ٻٻ‬ ‫ٻٻ‬ ‫[ ٻ‬Default] xL = xH = yL = yH = 0 ‫ٻ‬ dxL = 0, dxH = 2, dyL = 126, dyH = 6 ‫[ ٻ‬Reference] CAN, ESC L, ESC T, GS P ‫ٻ‬ ‫ ٻ‬ESC T n ‫[ ٻ‬Name] Select print direction in page mode ‫[ ٻ‬Format] ASCII ESC T n ‫ٻ‬ HEX 1B 54 n ‫ٻ‬ Decimal 27 84 n ‫[ ٻ‬Range] 0 അ n അ 3 or 48 അ n അ51 ‫[ ٻ‬Description] Selects the print direction and starting position in page mode.
PAGE 44
‫[ ٻ‬Notes] 1) When the command is input in standard mode, the printer executes only internal ‫ٻ‬ flag operation. This command does not affect printing in standard mode. ‫ٻ‬ 2) This command sets the position where data is buffered within the printing area ‫ٻ‬ set by ESC W.
PAGE 45
‫ٻ‬ 5) The reference starting position is that specified by ESC T. ‫ٻ‬ 6) This command operates as follows, depending on the starting position of the ‫ٻ‬ printing area specified by ESC T; When the starting position is set to the upper left ‫ٻ‬ or lower right, this command sets the absolute position in the vertical direction. ‫ٻ‬ When the starting position is set to the upper right or lower left, this command sets ‫ٻ‬ the absolute position in the horizontal direction.
PAGE 46
‫ٻٻ‬ ‫ٻ‬ 4) Any setting that exceeds the specified printing area is ignored. ‫ٻ‬ 5) This command function as follows, depending on the print ‫ٻ‬ starting position set by ESC T; ‫ٻ‬ When the starting position is set to the upper left or lower right ‫ٻ‬ of the printing, the vertical motion unit (y) is used. ‫ٻ‬ When the starting position is set to the upper right or lower left ‫ٻ‬ of the printing, the horizontal motion unit (x) is used.
PAGE 47
]U]UGiTpGjG ‫ٻ‬ ‫ٻ‬ The PORTI- PC40 supports the following bit-image command. ‫ٻ‬ Command Name ‫ٻ‬ ESC * Select bit image mode ‫ٻ‬ ESC X 4 Define user-defined bit image ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ESC * m nL nH d1 dk [Name] Select bit-image mode.
PAGE 48
‫ٻ‬ ‫ٻ‬ 4) If the bit-image data input exceeds the number of dots to be printed on a line, the excess data is ignored. ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ 5) d indicates the bit-image data. Set a corresponding bit to 1 to print a dot or to 0 to not print a dot.
PAGE 49
‫‪- When 8-dot bit image is selected‬‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‪- When 24-dot bit image is selected‬‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ڔڏ‬ ‫ٻۈۊھډۈۄێۊۊےډےےےڊڊڕۋۏۏۃٻ‬
PAGE 50
‫ ٻ‬ESC X 4 x y d1…dk ‫[ ٻ‬Name] Define user-defined bit-image ‫[ ٻ‬Format] ASCII ESC X 4 x y d1…dk ‫ٻ‬ HEX 1B 58 34 x y d1…dk ‫ٻ‬ Decimal 27 88 52 x y d1…dk ‫[ ٻ‬Description] ESC X 4 x y d1 ... d(x ૟y) ҏ defines a user-defined bit image using x ૟ҏ8 ‫ٻ‬ dots in the horizontal direction and y dots in the vertical direction.
PAGE 51
‫ٻٻ‬ ‫ٻٻ‬ ‫ٻٻ‬ ‫ٻٻ‬ ‫ٻٻ‬ ‫ٻٻ‬ ‫ٻٻ‬ ‫ٻٻ‬ ‫ٻٻ‬ ‫ٻٻ‬ ‫ٻٻ‬ ‫ٻٻ‬ ‫ٻ‬ ‫ٻٻ‬ ‫[ ٻ‬Note] ESC X 4 is supported in Porti_W,S produced after August,2002, but it’s not ‫ٻ‬ supported in others yet.
PAGE 52
]U^UGzGjG ‫ٻ‬ The PORTI- PC40 supports the following status transmission command. ‫ٻ‬ ‫ٻ‬ Command ‫ٻ‬ DLE EOT EOT ‫ٻ‬ Name Real-time paper status transmission ‫ٻ‬ ‫ ٻ‬DLE EOT EOT ‫ٻ‬ ‫ٻ‬ [Name] Real-time paper status transmission [Format] ASCII DLE EOT EOT HEX 10 04 04 Decimal 16 4 4 ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ [Description] Real time paper status transmission [Note] DLE EOT EOT is supported only by PORTI_T80.
PAGE 53
]U_UGiGjG ‫ٻ‬ ‫ٻ‬ The PORTI- PC40 supports the following barcode commands. ‫ٻ‬ Command Name ‫ٻ‬ GS h Set barcode height ‫ٻ‬ GS w Set barcode width ‫ٻ‬ GS k Print bar code ‫ٻ‬ GS H Select printing position of Human Readable Interpretation ‫ٻ‬ (HRI) characters ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ GS h n [Name] Set barcode height [Format] ASCII GS h n HEX 1D 68 n Decimal 29 104 n ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ [Range] 0 അ n അ 255 [Description] GS h n selects the height of a barcode.
PAGE 54
‫ྙٻ ٻ‬ ྙGS k m d1೨dk NUL ྚGS k m n d1…dn ‫[ ٻ‬Name] Print barcode ‫[ ٻ‬Format] ཛASCII GS ‫ٻ‬ HEX ‫ٻ‬ Decimal 29 ‫ٻ‬ ཛྷ ASCII GS 1D ‫ٻ‬ HEX ‫ٻ‬ Decimal 29 1D k m d1…dk NUL 6B m d1…dk 00 107 m d1…dk 0 k m n d1…dn 6B m n d1…dn 107 m n d1…dn ‫[ ٻ‬Range] ཛ 0 m 6 (k and d depends on the bar code system used.) ‫ٻ‬ ཛྷ 0 m 6 (n and d depends on the bar code system used.) ‫[ ٻ‬Description] GS k m d1…dk NUL selects a barcode system and print the barcode.
PAGE 55
‫ྚٻ‬ ‫ ٻ‬m ‫ ٻ‬65 ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ Barcode System Number of characters Remarks UPC-A 11 n 12 48 d 57 66 UPC-E 11 n 12 48 d 57 67 EAN13 11 n 13 48 d 57 68 EAN8 7n8 48 d 57 69 CODE39 1 n 255 48 d 57, 65 d 90, ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ d = 32, 36, 37, 43, 45, 46,47 70 ITF 1 n 255 (even number) 48 d 57 71 CODABAR 1 n 255 48 d 57, 65 d 68, d = 36, 43, 45, 46, 47, 58 ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ 72 CODE93 1 n 255 0 d 127 73 CODE1
PAGE 56
‫ٻ‬ processes the following data as normal data. ‫ٻ‬ 8) Be sure to keep spaces on both right and left sides of a bar code. ‫ٻ‬ Spaces are different depending on the types of the bar code. ‫[ ٻ‬Reference] GS h, GS w, GS H, ESC L, ESC W, ESC FF ‫ٻ‬ ‫ ٻ‬GS H n ‫[ ٻ‬Name] Turn HRI characters print mode ON/OFF ‫[ ٻ‬Format] ASCII GS H n ‫ٻ‬ HEX 1D 48 n ‫ٻ‬ Decimal 29 72 n ‫[ ٻ‬Range] n = 0, 1 ‫[ ٻ‬Description] GS H n turns HRI characters print mode on or off.
PAGE 57
]U`UGtGmGjG ‫ٻ‬ The PORTI- PC40 supports the following macro function commands; ‫ٻ‬ ‫ٻ‬ Command Name ‫ٻ‬ GS : Start/end macro definition ‫ٻ‬ GS ^ Execute macro ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ GS : [Name] Start/End macro definition [Format] ASCII GS : HEX 1D 3A Decimal 29 58 ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ ‫ٻ‬ [Description] Starts ends macro definition. [Notes] 1) Macro definition starts when this command is received during normal operation.
PAGE 58
‫ ٻ‬GS ^ r t m ‫[ ٻ‬Name] Execute macro. ‫[ ٻ‬Format] ASCII GS ^ r t m ‫ٻ‬ HEX 1D 5E r t m ‫ٻ‬ Decimal 29 94 r t m ‫[ ٻ‬Range] 0 <= r <= 255 ‫ٻ‬ 0 <= t <= 255 ‫ٻ‬ m = 0, 1 ‫[ ٻ‬Description] Executes a macro. ‫[ ٻ‬Notes] 1) r specifies the number of times to execute the macro. ‫ٻ‬ 2) t specifies the waiting time for executing the macro. ‫ٻ‬ 3) m specifies macro executing mode. ‫ٻ‬ When LSB of m = 0 ‫ٻ‬ The macro executes r times continuously at the interval specified by t.
PAGE 59
]UXWUGtGjGjG ‫ ٻ‬The PORTI- PC40 supports the following mechanism control commands; ‫ٻ‬ ‫ٻ‬ Command Name ‫ٻ‬ GS V Select cut mode and cut paper ‫ٻ‬ ESC i Partial cut (One point center uncut) ‫ٻ‬ ‫ٻ‬ ‫ ٻ‬GS V m ‫[ ٻ‬N1ame] Select cut mode and cut paper ‫[ ٻ‬Format] ASCII GS V n ‫ٻ‬ HEX 1D 56 n ‫ٻ‬ Decimal 86 n ‫[ ٻ‬Range] n=0, n=1 ‫[ ٻ‬Description] GS V m select a paper cutting mode and then cut the paper.
PAGE 60
]UXWUGtGjGyGjG ‫ٻ‬ The PORTI-PC40 supports the following magnetic card reader commands; ‫ٻ‬ ‫ٻ‬ Command Name ‫ٻ‬ ESC M C Set 2 track card reader mode. ‫ٻ‬ ESC M D Set 3 track card reader mode. ‫ٻ‬ ESC M E Set 2,3 track card reader mode. ‫ٻ‬ EOT Cancel card reader mode ‫ٻ‬ ‫ ٻ‬ESC M C ‫[ ٻ‬Name] Set 2 track card reader mode.
PAGE 61
‫ ٻ‬EOT ‫[ ٻ‬Name] Cancel card reader mode. ‫[ ٻ‬Format] ASCII EOT ‫ٻ‬ HEX 04 ‫ٻ‬ Decimal 4 ‫[ ٻ‬Description] Cancel card reader mode. ‫ٻ‬ ‫ ୔ ٻ‬Card specification ‫ ٻ‬The table below summarizes the format of the data stored on each magnetic track.
PAGE 62
]UXXUGtGGG ‫ٻ‬ The PORTI- PC40 supports the following miscellaneous function commands; ‫ٻ‬ ‫ٻ‬ Command Name ‫ٻ‬ GS P Set horizontal and vertical motion units ‫ٻ‬ ESC @ Initialize printer ‫ٻ‬ ESC L Select page mode ‫ٻ‬ ESC S Select standard mode ‫ ٻ‬GS P x y ‫[ ٻ‬Name] Set horizontal and vertical motion units.
PAGE 63
‫ٻ‬ When the print starting position is set to the upper right or lower left of the printing ‫ٻ‬ area ESC T (data is buffered in the paper feed direction); ‫ٻ‬ Command using x : ESC 3, ESC J, ESC W, GS $, GS \ ‫ٻ‬ Command using y : ESC SP, ESC $, ESC W, ESC \ ‫ٻ‬ 4) The command does not affect the previously specified values. ‫ٻ‬ 5) The calculated result from combining this command with others is truncated to ‫ٻ‬ the minimum value of the mechanical pitch.
PAGE 64
‫ٻ‬ 4) This command sets the position where data is buffered to the position specified ‫ٻ‬ by ESC T within the printing area defined by ESC W.
PAGE 65
‫ٻ‬ ‫ٻٻ‬ Set right-side character spacing : ESC SP ‫ٻ‬ Select default line spacing : ESC 2, ESC 3 ‫ٻ‬ 6) The following commands are enabled only to set in standard mode. ‫ٻ‬ Set printing area in page mode : ESC W ‫ٻ‬ Select print direction in page mode : ESC T ‫ٻ‬ 7) The following commands are ignored in standard mode.
PAGE 66
hG G G G G G G G G G G G G G G G G G G G G G G G G G G G G G G G ‫ ٻ‬A. MISCELLANEOUS NOTES ‫ٻ‬ 1. Printer mechanism handing ‫ٻ‬ 1) Do not pull the paper out when the cover is closed. ‫ٻ‬ 2) Because the thermal elements of the print head and driver ICs are easy to break, so do not ‫ٻ‬ touch them with any metal objects. ‫ٻ‬ 3) Since the areas around the print head become very hot during and just after printing, do not ‫ٻ‬ touch them.
PAGE 67
‫ٻ‬ 7) If the surface of thermal paper is scratched with a hard metal object such as a nail, ‫ٻ‬ the paper may become discolored. ‫ٻ‬ ‫ٻ‬ - Notes on thermal paper storage ‫ٻ‬ Since color development begins at 70¶C (158¶F), thermal paper should be protected ‫ٻ‬ from high temperature, humidity, and light, both before and after printing. ‫ٻ‬ 1) Store paper away from high temperature and humidity. ‫ٻ‬ Do not store thermal paper near a heater or in enclosed places exposed to direct sunlight.