User's Manual

ManualsBrandsWoori Technology ManualsAV receiversAV RECEIVER

you wish to choose another option to skip the sub-

woofer measurements and either complete the

EQ Design or return to the

EZSET/EQ

MAIN

menu.

• If there was an error during the test, the Design

Step 2 Error message will appear. Follow the on-

screen instructions to check speaker connections

(

if no sound was heard from the speaker during

the test), check the microphone placement to make

ertain it is no further than half the distance from the

speaker to the listening position and pointing directly

at the speaker, or increase the volume by 5dB. After

taking the corrective steps, make sure the cursor is

pointing to

REPEAT TEST and press the

OK/Enter Button E on the TC 30 or the Set

Button

on the ZR 10 remote. Select the

speaker again and repeat the steps as needed until

a successful measurement is made.

Steps 3 and 4: The third and fourth steps in the

EzSet/EQ II Design process are the measurement for

the subwoofers, if present. Although the subwoofers

are generally considered one speaker position, since

the AVR 745 may be used with two subwoofers, two

separate measurement steps must be combined for a

complete EQ Design.

When the

SUBWOOFER DESIGN message

appears, make certain that the cursor is pointing to

CONTINUE TO SUB DESIGN and press

the

OK/Enter Button E on the TC 30 or the Set

Button

on the ZR 10 remote control. The

EZSET DESIGN STEP 3 (Figure 20)

message will appear.

Figure 20

Follow the instructions (using the extender rod if nec-

essary),

to make sure that the microphone is at ear

level and to the left of where the microphone was

placed during the Far Field measurements. Press the

OK/Enter Button E on the TC 30 or the Set

Button

on the ZR 10 remote to continue.

When the

WARNING message appears on

screen, press the

‹/› Navigation Buttons D

to start the test. The test tone will be sent to the sub-

woofer(s) and the system will then pause slightly to

perfor

m the needed calculations.

When the calcula-

tions are complete, the

EZSET DESIGN

STEP 4 message will appear.

The instructions here are identical to those in Step 3

except that the microphone should be placed to the

right of where it was during Far Field measurements.

Press the OK/Enter Button E on the TC 30 or the

Set Button

on the ZR 10 remote to continue.

When the subwoofer tests in Steps 3 and 4 are com-

lete, a message (Figure 21) will appear after a brief

pause to display the results.

Figure 21

• If the tests were successful, the message will show

the number of subwoofers, as shown in Figure 21.

You may either press the

OK/Enter Button E on

the TC 30 (or the

Set Button

on the ZR 10

remote) to continue to the next step and conclude

the EzSet Design process, or press the

⁄

Navigation Buttons D

and then the

OK/Enter Button E on the TC 30 (or the Set

Button

on the ZR 10 remote) to either repeat

the subwoofer test or return to the main EzSet/EQ

menu. In most cases you should select “Continue.”

• If the tests were not successful, a message similar

to Figure 21 will appear, except that the top line

will flash

DESIGN STEP 3/4 ERROR.

Follow the suggestions in the message to verify that

the

subwoofer

(s) is properly connected and that the

microphone is in the proper position,

and increase

the volume level by 5dB

Then, press the

OK/Enter

Button

E on the

TC 30 or the

Set Button

on the ZR 10 remote to repeat the test as often as

needed until a successful result is achieved.

Step 5: When all measurements are successfully

completed, the final step in the EzSet Design process

is to save the settings into the AVR 745’s memory.

ou may program up to three different EQ settings to

accommodate differences in placement of the micro-

phone to reflect alternate listening positions, but we

recommend that you create two settings and leave

one memor

y in the “bypass”

mode so that you have

the ability to compare the two equalized settings

against a “straight through” setting that has no equal-

ization applied.

At the conclusion of the measurements for an

EQ Design, make certain that the

EZSET/EQ

DESIGN DONE menu (Figure 22) is on your

screen.

It will appear when you are done with the

Subwoofer design, or when you “skip” through the

Near Field and/or Subwoofer steps.

igure 22

The “test drive” feature allows you to listen to the

ource that was playing before the EzSet/EQ Design

process was initiated, and it is a good way to make

sure that you are pleased with the results. The

“Warning” refers to the fact that the volume level may

have been raised during the Design process, so it is

always a good idea to lower the volume a bit. You may

always raise it once the playback starts.

With the cursor pointing to

CONTINUE, press

the

OK/Enter Button E on the TC 30 or the Set

Button

on the ZR 10 remote, and playback will

resume while the on-screen menu changes to the

DESIGN PREVIEW page (Figure 23).

Figure 23

• If you are pleased with the sound, press the

OK/Enter Button E on the TC 30 or the Set

Button

on the ZR 10 remote to move to the

next screen and store the settings.

• If the sound is not to your liking, press the

⁄

Navigation Buttons D

so that the cursor is

next to

NO and then the OK/Enter Button E on

the TC 30 or the

Set Button

on the ZR 10

remote

. Follow the on-screen prompts in the menus

to return to the

EZSET/EQ MAIN menu

and repeat the EQ Design process.

•

If this is your first attempt at running

EzSet/EQ

II,

we recommend that you save the settings

even if

you are not sure whether you like them,

then rerun

the

EQ Design process again. Since the AVR 745 is

able to store multiple EQ Design settings, this will give

you the opportunity to compare two different designs

to the bypass mode with no equalization applied. Y

may then select the preset you like best.

If you proceed to store the settings

the next menu will

let you select which memor

y position will be used

(Figure 24).

DESIGN PREVIEW *

EQ design has been

completed.

Do you like your current

listening experience?

YES

→→

* EZSET DESIGN DONE *

To test drive your

Design, please connect

audio source, adjust

volume and play.

CONTINUE

BACK TO EZSET/EQ MAIN

→→

* DESIGN STEP 3/4 RESULTS *

EZSET successful

Detected speaker config:

SUBWOOFER 1:YES

SUBWOOFER 2:NO

CONTINUE

REPEAT SUBWOOFER TEST

BACK TO EZSET/EQ MAIN

→→

EZSET DESIGN STEP 3

Put mic at ear level,

3ft/0.9m to the left

Of the preferred

listening position.

CONTINUE

BACK TO EZSET/EQ MAIN

→→

SYSTEM CONFIGURATION

32 SYSTEM CONFIGURATION

AVR 745 OM 5/15/06 5:00 PM Page 32