User's Manual

ManualsBrandsWoori Technology ManualsAV receiversAV Receiver

INSTALLATION AND CONNECTIONS 19

INSTALLATION AND CONNECTIONS

the Video 4 inputs set to control a satellite receiver.

However, you may reassign the commands for any

type of device to either button on the remote using

the instruction shown for “Changing Devices” as

shown on page XX. You may also learn the codes

for the device connected to any input by following

the instructions for “Learning Codes” shown on

page XX.

4. Connect the analog left/right audio and composite

video or S-Video and analog left/right audio outputs

of a DVD player to the DVD Audio and Video

Input Jacks §J on the rear panel.

5. Connect the optical or coaxial digital audio outputs

of a DVD player, satellite receiver, cable box, HDTV

tuner or video game to any of the Optical or

Coaxial Digital Inputs ™∞ . The

recommended connection for a DVD player is to

use a Coaxial digital link connected to the Coaxial

Digital Audio Input 1, but you may change the digi-

tal

audio input assignment for any source using the

IN/OUT SETUP menu as described on

page 21 or the Digital Input Selector p

on the front panel or remote, as described on

page XX.

NOTE: When connecting a device such as a digital

cable box or other set-top tuner product with a digital

audio output, we recommend that you connect both

the digital and analog outputs of the product to your

AVR. The audio input polling feature of the AVR will

then be able to make certain that you have a constant

audio feed, since it will automatically switch the audio

input to the analog jacks if the digital feed is interrupted

or not available for a particular channel.

6. Connect the Video Monitor Output O jacks on

the receiver to the composite or S-Video input of

your television monitor or video projector.

7. If your DVD Player has Y/Pr/Pb analog component

video outputs, connect them to the DVD Com

ponent Video Inputs %. Although this set of

inputs may be assigned to any of the five video

inputs on the AVR 7 30 0, the factory default is for

this input to be assigned to the DVD. Remember to

make a digital audio connection between the DVD

player and the AVR, with the Coaxial Digital

Input 1 † being the factory default. For informa-

tion on changing the input assignments for either

the component video jacks or the DVD player’s

audio connection, see page XX.

8. If you have other devices with Y/Pr/Pb or RGB

component video outputs, connect the source

device to the Component Video 1 or 2 Inputs

GH. The audio connections may be made to

any of the ?????? panel audio inputs or the

Optical or Coaxial Digital Inputs ®ß

. When using either of the Component

Video Inputs, make certain that the audio and video

inputs are properly configured in the IN/OUT

SETUP menu, as described on page XX.

9. If the component video inputs are used, connect

the Component Video Monitor Outputs E to

the component video inputs of your TV, projector or

other display device.

10.If you have a camcorder, video game or other

audio/video device that is connected to the DPR

on a temporary, rather than permanent, basis, con-

nect the audio, video and digital audio outputs of

that device to

the Front-Panel Inputs

.A device connected

here is selected as the

Video 5 input, and the digital inputs must be

assigned to the Video 5 input. (See page 21 for

more information on input configuration.)

Video Connection Notes:

• When connecting the AVR 7300 to a “digital ready”,

“HDTV compatible” or High Definition display, which is

any device capable of accepting an input signal of

480P or higher, you are able to take advantage of

the unit’s advanced video processing circuitry con-

verts all incoming video signals, regardless of the way

they are connected to the AVR. Since the AVR 73 00

is also among the very few products that display the

on-screen menus with up-converted video, the con-

nection from the AVR 7300 to the display need only

be one set of Y/Pr/Pb component video cables.

• When source devices such as a progressive scan

DVD player or HDTV set-top box are connected to

the AVR 7300 via component video connections, it

is also necessary to connect the standard, composite

or S-Video outputs of the source device to the AVR

7300 if you wish to take advantage of the record

outputs or have video routed to a second room. The

record outputs and multiroom system cannot accept

component inputs, nor are component inputs down

converted for use with these outputs.

• When connecting the AVR 7300 to a standard, ana-

log video display that has standard composite and

S-Video inputs only, component video inputs may

not be used. If you have a mix of composite and S-

Video input sources, note that the AVR 730 0 will

down convert S-Video inputs to a composite output,

but it will not convert composite video to S-Video.

System and Power Connections

The AVR 7 300 is designed for flexible use with multi-

room systems, external control components and

power amplifiers.

Main Room Remote Control Extension

If the receiver is placed behind a solid or smoked

glass cabinet door, the obstruction may prevent the

remote sensor from receiving commands. In this

event, an optional remote sensor may be used.

Connect the output of the remote sensor to the

Remote IR Input D jack.

If other components are also prevented from receiving

remote commands, only one sensor is needed. Simply

use this unit’s sensor or a remote eye by running a

connection from the Remote IR Output C jack to

the Remote IR Input jack on Harman Kardon or other

compatible equipment.

Multiroom IR Link

The remote room IR receiver should be connected to

the Multiroom IR Input D jack on the AVR 730 0’s

rear panel.

If other Harman Kardon compatible source equipment

is part of the main room installation, the Remote IR

Output

jack on the rear panel should be connected

to the IR IN jack on source equipment. This will enable

the remote room location to control source equipment

functions.

NOTE: All remotely controlled components must be

linked together in a “daisy chain.” Connect the IR OUT

jack of one unit to the IR IN of the next to establish

this chain.

Multiroom Connections

The AVR 7 300 is equipped with multizone capabilities

that allow it to send an audio and/or video source to

a remote zone that i s different from the one selected

for use in the main room. Please note that this capa-

bility applies to analog inputs from sources such as the

AVR’s tuner, tape decks or VCRs. If you wish to use a

source such as a DVD or CD player that is normally

connected via a digital connection, it is necessary to

run an analog connection from the source to the AVR

or to use the Main Downmix input option, as explained

on page XX.

Depending on your system’s requirement,

three options are available for remote room audio

connection:

Option 1: Use high-quality, shielded audio intercon-

nect cable from the AVR 7300’s location to the

remote room. In the remote room, connect the inter-

connect cable to an optioinal external stereo power

amplifier. The amplifier will be connected to the room’s

speakers. At the AVR 730 0, plug the audio intercon-

nect cables into the Multiroom Audio Outputs ø

on the DPR 2005 ’s rear panel.